1 Introduction............................4 2 Getting start............................4 2.1 Introduction.........................4 2.2 Familiar with NL-8300 .......................4 2.2.1 Unpacking ........................4 2.2.2 Housing ........................5 2.2.3 Detail function describe of POS................9 2.2.4 Every interface functions and pin definition ............10 2.3 Startup/Operation/Shut down/reboot.................13 2.4 Start-up interface and its main function ................14 2.5 Program download ......................15...
Page 3
5.2 Battery use.........................45 5.3 Magnetic-card ........................46 5.4 IC card use ........................47 5.5 ATM IC card、SIM card and SAM card use ..............48 5.6 Printer..........................49 5.7 Battery Charge ........................50 5.8 Other points for attention ....................51 5.9 How to Load Printer Paper....................52 5.10 Troubleshooting ......................55...
The content of this manual using the all function type POS to induce. 2 Getting start 2.1 Introduction This chapter will introduce NL-8300 from unpacking to deeply. It will include housing, principle, detail description of functions, every PIN definition, and every function of interface, right setting and other relevant settings.
2.2.3 Detail function describe of POS Clock Display the correct time Can read the track I 2 3 of magcard which meet the standard of Magcard ISO7816. Support 75 BPI and 210BPI and two-way slot card. 128*64 LCD, using EL uniform backlight, can adjust contrast, display standard ASCII character, international GB18030/GB2312 Chinese ideograph and graphics document.
2.2.4 Every interface functions and pin definition a. Rs232 interface ① Function: Main CPU using CPLD connected the electronic level conversion chip of RS232., can use to connect the serial port. ② Every PIN of interface introduction: PIN1: Grounding PIN2: Empty PIN3: Sending date PIN4: Receiving date PIN5: Empty...
Page 11
c. MODEM and RS232 serial port ① Function:Build-in wire MODEM, support MODEM communication, and synchronization rate is 1200BPS, asynchronism is 1200/2400BPS. Main CPU using CPLD connected the electronic level conversion chip of RS232., can use to connect the serial port. ②...
Page 12
e. IC card. ① Function: IC card use IC card interface chip connected with assistant CPU. Assistant CPU can read and write the date of IC card. ② Every PIN induction of interface: please check standard ISO7816 PIN1:ICC Power +5V PIN2:ICC Reset Signal PIN3:ICC Clock Signal PIN4:Null...
2.3 Startup/Operation/Shut down/reboot 2.3.1 Startup Press “ ” button of keyboard for 3-5 sec 2.3.2 Operation After starting, about 5 seconds the POS will entry the trade program. If the users don’t want to wait for 5 seconds or after 5 second the program still not running, user can press ENTER to entry the trade program by manual.
2.4 Start-up interface and its main function Picture below is the default main interface, Down, self-check and management are the firmware program. Using operation can open the user-defined program, indicate the current interface’s operation location. NL8300 V3.58 08-04-20 10:08:08 Down Self Optio load...
2.5 Program download When running posdownload.exe for the first time, the following window may show up, just click on the OK button to choose the default setting. Then the main window will be shown.
Page 16
Selecting the download type This tool supports downloading of 3 different files: user program, key program and normal file. They will be downloaded into different storage space respectively, i.e., User Program will be downloaded into the user program space(up to 320 kB), Key Program will be downloaded into the key management program space(up to 64 kB), while normal files will be download into the flash file system space(up to 2MB).
Page 17
Trouble shootings Q: The download session doesn’t start after I click on the Get Ready(W) button. A: Be sure to select the correct COM port for download. Make sure the download data line has been connected to the POS’s RS232 port. Make sure the POS has been put into the download mode by pressing Enter on the Download icon.
3 The testing on functional modules In order to facilitate the technical maintenance staff on-site maintenance for this product, problem positioning and hardware repair. We provide this self-check program in the BIOS. Using this program you can do all the manual testing on each of the POS’sthe functional module . 1.Version 2.Keyboard 3.File system...
3.1 Version The first page will display software version: main CPU, assistant CPU, document system, micro print device version, Detail please see Fig3-1 bellow Main CPU:V3.58 Secondary CPU:V4.21 File System:V9.30 Printer Driver:V1.30 Fig 3-1 The second page displays the hardware version, FRAM size, Flasf1, flasf2. Detail please see Fig3-2 bellow Hardware Version:V4.2 FRAM :...
3.2 Keyboard To test the keyboard, firstly testing whether every keys and its name, code is corresponding. For example: presses “2”, detail please see Fig3-4 below. Press a key → ( 2 ) keycode:0x32 Fig3-4 Press “Cancel ” to quit, then test number input function, see Fig3-5 Digit-only input test: 0123456789_ Fig3-5...
3.3 Files Test the file system of flash disk. Firstly, display the free space of flash disk and the number of available file handlers (the number of files that can be opened without closing the files that have already been opened) Press Key “back”...
3.4 Magcard Test Perform Card Reading Test, shown as Fig3-9. ――Magcard Test―― 1.The 2&3 Track 2. The 2 Track 3 The 3 Track 4. The 1&2&3 Track Fig3-9 According your need, select the track numbers to be read; support bi-directional swipe; when swiping the card, the magnetic stripe should be facing the LCD.
3.5 IC/SAM Test the IC/SAM card, please fig3-11. Support 4 SAM Card? 1.YES 2.NO fig3-11 In the fig 3-11 press 1, will make the 4SAM card test, means use SIM1 or SAM3 as SAM4 card to test, if press 2, there aren’t make any test of SIM1 or SAM3. In the fig3-11 waiting 3-5 seconds without any operation, will choose “2.
3.6 Printer Fig3-13 shows the main menu of Printer Test NL8300 POS ___Printer Test___ 1 Single Page 2 Continuous Fig3-13 ① Press Key “1” to do the single page test, which means printing one page of selected content only. ② Press Key “2” to do the Continuous print test, which means continuously printing many pages of selected content.
Page 25
a、Under the menu shown as figure 3-14, Press Key “1” to print the testing page, means print the normal word and picture. See fig 3-15. The content of printing is icon, time, and voltage. fig 3-15 b、Under the menu shown as figure 3-14, Press Key “2” to print the Blank Page, which is usually used to adjust the printer head moving speed.
3.7 Communication 1. AUX1 Test 2. AUX2 Test 1.AUX Test 3. AUX Selftest 4. AUX 1/2Direct Connect 1. Open 2. Close 2.MC35 3. Signal Test 4. COPS 5. Is Connect? Commun- 6. Initialize ication 1. pppOpen 2. pppClose 3. Telnet 3.TCP/IP Test 4.
Page 27
Make the communication test. The interface please see Fig 3-16 _____Connection Test_____ 1 Ports 2 Wireless 3 TCP/IP 4 MODEM 5 Base Echo Fig 3-16 ① In Fig3-16 press 1 to make the assistant port test, entry Fig 3-17 __AUX Commu Test ___ 1 AUX1 Test 2.AUX2 Test 3 AUX Selftest equipment)...
Page 28
Received XXX Pack ErrCount:0 Fig 3-19 Aux Test requires Self-test Head, which short circuits the Send and Receive PIN of Aux Port download cable. The XXX shown in figure 3-19 indicates the number of successful attempts. b. In the Fif3-17 press 3 to make the self-check of assistant port 1 and 2. When initialization of assistant port 1 is success, the LCD will display 115200 8 N 1.
Page 29
② In Fig3-17 Press 2 makes the test of wireless, interface please see Fig 3-20 ____ Wireless Test____ 1. Open 2 Close 3. Signal 4 COPS 5. Is Connect? 6 Initialize Fig 3-20 a. Press 1 opens the wireless module b.
Page 30
④ In Fig3-17 Press 4 to make the test of the wire modem, please see Fig3-22 __ MODEM Test___ 1 Country Set 2 Dial Initialize 4 Version 5 Baud Rate Test Fig3-22 a、 Press 1 to entry the country setting, there are four choice, can choose the communication environment base on the requirement.
Page 31
c、Press 3 to initial the MODEM, see Fig3-24. ____ MODEM Init ____ 1. Normal 2. Normal With anti-jamming 3. Fast With (anti-jamming) 4. Reset 5. Select S Register Fig3-24 Normal speed: Sending the AT Command (Reference: AT Command Set Reference.htm)to evaluate the initial MODEM. Normal speed noise-immune: Sending different AT Command to initial MODEM High speed noise-immune: Sending different AT Command to initial MODEM and make the carrier detect.
Page 32
“AT DP603” When sending succeed, the connection has build. ⑤ Press 5 to make the Base machine Echo test. If you Base machine type is NL-8300, you can use the option, testing whether can communication with base. See Fig3-27 Communicating with Base Press ESC to quit.
3.8 Battery POS has the AD test function, display the current voltage and AD output of POS. then make the charge/discharge test, see Fig3-28、Fig3-29: Voltage Is 4.20 V AD output:*** Fig3-28 1. Discharge 2. Discharge Record 3. Charge 4. Charge Record Fig3-29...
4 Operational parameter setting Management menu is used to set the parameters for POS. Before you entry the management menu, you need to enter the password “159951”, Fig4-1 is the management menu diagram. 1. Display 2. Keyboard 3. Clock 4. Password 5.
4.1 Display LCD display set of configuration, see Fig4-2. 1.Cont rast 2.Backlight 3.Screen Turn Left/Right 4. Screen Turn Up/Down 5.Shift Left 6.Set Bias Fig4-2 ① Press 1 to set the Contrast ratio: Setting the contrast radio of LCD, can change the definition of LCD.
② Press “Key 2” to set Keyboard Repeat Rate, which is the input speed when one key is being kept pressed; Choose from High, Med, and Low; Press Confirm to save the setting. 4.3 Clock Adjust Date, shown as Fig4-4: 1.Change Date 2.Change Time 3.Startup Clock Style...
Under the Menu shown in Fig4-4; press Key “2” to select the clock display format for ③ boot-up screen, shown as Fig4-7. Press “Cancel” to save and quit. Please Select Startup Clock Style: 1. Data and Time 2. Time only ESC to Back Fig4-7 4.4 Password...
4.5 Auto-run Choose if user program is auto run after boot, shown as Fig4-10: Allow User Programme Run Automatically? ⒈ Yes ⒉ Fig4-10 ① YES: When POS is booting, wait for 2 sec at the main menuthen the POS will run the user program automatically ②...
4.8 Hardware Setting hardware, see Fig4-11 1. Version Of Hareware 2. Communition Rate Of Sub-CPU 3. Volume Of Battery 4. Machine ID 5. Property Info Fig4-11 ① Press 1 to choose the hardware version, see Fig4-12. Please Select Hardware Version 1.
Select Volume of Battery: 1. 2500mAh 2. 1500mAh To Back Fig4-14 ④ Press 4 can input the ID number of the machine ⑤ Press 5 to display the information property of POS 4.9 Language Setting display language, shown as Fig4-15: Please Select language: 1.Chinese 2.
4.10 Wireless Setting wireless parameter, see Fig4-16. 1. Exist Wireless 2. Wireless Typt 3. Telephone Fig4-16 ① Press 1 to ensure the machine whether install the wireless module. See Fig4-17. Select Wireless module status 1. Exist 2. No Exist To Back Fig4-17 ②...
4.11 Download Entry the interface of base machine parameter, please see the Fig4-19 1. Download 2. MODEM 3. Desk CPLD Fig4-19 ① Press 1 to choose the way of downloading, see Fig4-20 Please Select Download Mode: 5. From Handset 6. From Desktop ESC To Back Fig4-20 ②...
To avoid electric shock, disconnect the power before cleaning. Do you use AC plug in outdoor or moist environment. Use original Power Supply Only. If the plug does not fit with the mains jack, please contact Newland Service Team for replacing or ask an electrician to install a suitable mains jack.
●Only can use the lithium cell and charger design for this product. Using other batteries and chargers could be dangerous. When the capacity of battery become low need to change the new one, please contact the staff of Newland scan company. ●Avoid putting the battery into the high temperature environment, avoiding the direct sunlight, can not in use higher than +60 degrees Celsius (+140 degrees Fahrenheit) in the environment.