VolantexRC RANGER 1600 User Manual
  1. Manuals
  2. Brands
  3. VolantexRC Manuals
  4. Toy
  5. RANGER 1600
  6. User manual

VolantexRC RANGER 1600 User Manual

Hide thumbs

Advertisement

Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RANGER 1600 and is the answer not in the manual?

Questions and answers

Related Manuals for VolantexRC RANGER 1600

Summary of Contents for VolantexRC RANGER 1600

  • Page 2: Safety Precautions And Warnings

    Do not use with incompatible components or alter this product in any way outside of the instructions provided by VolantexRC Co.,Ltd.. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
  • Page 4 Secured servo arm to tightened by the rubber ring. servo with a PWA2.3*4 screw. * Step 5-6 For Ranger 1600 5. Slot the wing connecting rod to one wing, then 6. Secure the wings to the fuselage with the connect another wing through the hole of the "click &...
  • Page 5 Propeller 8040 Propeller Washer Adaptor (6mm Inner Diameter) Propeller Washer Propeller Washer (6mm Inner Diameter) (5mm Inner Diameter) Propeller 8040 Ranger 1600 Ranger 2000 11. Install the propeller to the motor by the order as shown above. 5 / 16...

  • Page 6: Centering The Control Surfaces

    12. Depend on which function you need, cover on the camera mount(for FPV flight) or the canopy(for regular flight). Centering the Control Surfaces threaded end of the metal pushrod) so you can insert the pin in the OUTERMOS T hole on each control horn. It the centering adjustments are complete.
  • Page 7 If t he rudder is angled off to the left carefully remove the clevis from the control horn and screw it clockwise) one half to one full turn then insert the pin back into the outermost hole in the control horn. V iew the vertical t ail and rudder from directly above again and continue adjusting the length/position of t he pushrod/ clevis until the rudder is centered appropriately.

  • Page 8: Center Of Gravity

    Center of Gravity 70±5mm 70±5mm The ideal C .G.position is behind t he leading edge measured a t where the wing meets the Flight Checklist PLEASE NOTE: This checklist is NOT intended t o replace the content included i n this instruction manual.
  • Page 9 normally. the battery plug. If you want to turn off the transmitter you must ensure that the battery of the plane 9 / 16...

  • Page 10: Flying Conditions

    Find a Flight Field crowded neighborhood areas or in areas that are not free of people and obstructions. more forgiving surface that causes less damage in the unfortunate event of a c rash. Short grass i s better for takeoffs and landings as grass that is too takeoffs and landings on a smoother surface (such Fly in spacious ground w ithout obstacles and boskage.

  • Page 11: Perform A Range Check

    Perform a Range Check performing a range test is a good way to detect problems that could cause loss of control such as low batteries defective or damaged radio components or radio interference. This usually requires an assistant and should be First turn on the transmitter.

  • Page 12: Rog(Rise Off Ground) Take Off

    ROG(Rise off Ground) Take off and takeoff easier. Slowly advance the throttle, adding rudder correction as needed to keep the model rolling gentle climb. controls as necessary to establish a gentle turn away from the runway. Hand-Launch advance t he t hrottle to full power. Your assistant should run a few s teps w ith the p lane held high above h is head, and then give the model a swift, but controlled toss at a level, or slightly nose - up attitude.Initially, the elevator to establish the climb.

  • Page 13: After Flight

    Landing Make sure that the airplane initiates an ascending glide path. If necessary, add power to extend the glide path to reach control the glide path and altitude. Continue to apply elevator until the mode l touches down at which time you should be holding full, or nearly full up elevator.
  • Page 14 2. Connect the white 4-pin connector from battery to the mating connector on the charger. CAUTION: You must be careful to ensure proper polarity before making the connection. And while the white connectors are ‘keyed’ to minimize the risk of a reverse polarity connection, if you force them it is possible to make connection with the incorrect polarity potentially causing damage to the battery and/or charger.
  • Page 15 15 / 16...

This manual is also suitable for:

Ranger 2000757-7757-8

Table of Contents

Save PDF