Ruckus Wireless ZoneFlex 7782-E Mounting Manual

ZoneFlex 7782-E Access Point

Mounting Guide

CAUTION!
THE MINIMUM SOFTWARE REVISION FOR ALL 7782
APs IS ZONEFLEX (ZF) 9.5.1 OR LATER.
DO NOT CONNECT ANY 7782 AP TO A RUCKUS WIRELESS
CONTROLLER WITH ZF 9.5.0 OR EARLIER.
This Mounting Guide provides step-by-step instructions on how
to field-install the Ruckus Wireless ZoneFlex 7782-E External
Antenna (9x1-7782-xx81) access point (AP).
For detailed information on planning the installation, pointing the
external antennas, performing a site survey, preparing the AP at
the depot and shipping to the field, and configuring the external
antenna gain, refer to the ZoneFlex 7782 Dual Band 802.11n
Outdoor Access Point Installation Guide. For information on
operating the AP, refer to the ZoneFlex Outdoor Access Point
User Guide. Both documents are available at
https://support.ruckuswireless.com.
WARNING:
Only trained and qualified personnel should be
allowed to install, replace, or service this equipment.
WARNING:
Installation of this equipment must comply with local
and national electrical codes.
CAUTION:
Make sure that you form a 80mm - 130mm (3"-5")
drip loop in any cable that is attached to the AP or the building.
This will prevent water from running along the cable and entering
the AP or the building where the cable terminates.
CAUTION:
Be sure that grounding is available and that it meets
local and national electrical codes. For additional lightning
protection, use lightning rods and lightning arrestors.
CAUTION:
Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING:
Ruckus Wireless strongly recommends that you wear
eye protection before mounting the AP.
B Y B
EFORE OU EGIN
Before deploying Ruckus Wireless products, please check for the
latest software and the release documentation.
• User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents
Copyright © 2013 Ruckus Wireless, Inc.
Published December 2013, Part Number 800-70554-001 Rev A
• Software Upgrades are available at
http://support.ruckuswireless.com/software
• Open Source information is available at
http://opensource.ruckuswireless.com
• Software License and Limited Warranty available at
http://support.ruckuswireless.com/warranty
T G O L
HIS UIDE IN THER ANGUAGES
请从以下网站获得该指南的简体中文版
•
https://support.ruckuswireless.com.
• Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
こ の ガ イ ド の日本語版は
• https://support.ruckuswireless.com
で ご 覧 く だ さ い。
이 가이드의 한국어 버전은 웹 사이트
•
(https://support.ruckuswireless.com) 에서 확인하시기 바랍니
다 .
• Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
• Puede ver la versión en español (América Latina) de esta guía
en https://support.ruckuswireless.com.
P C
ACKAGE ONTENTS
Before deploying your AP in the field, verify that all items listed
below are included in the package. If any item is damaged or
missing, notify your authorized Ruckus Wireless sales
representative. Also, make sure that you have the required
hardware and tools.
• One 7782-E AP (A in Figure 1); includes one 12mm M6x1
earth ground screw with split lock and flat washers
• One AC power cable input end connector (B in Figure 1)
• Two M25 data cable glands (C in Figure 1)
• One green/yellow earth ground wire with ring terminal (D in
Figure 1)
• One loop-and-eye safety cable (E in Figure 1)
• One wall- or pole-mount hanger mount (F in Figure 1)
• One extension bracket (G in Figure 1)
• One AP mounting bracket (H in Figure 1)
• Two sets 40mm M8x1.25 hex bolt with split lock and flat
washers (I in Figure 1)
• Six SAE32-sized stainless steel clamps, 2.5-inch diameter (J
in Figure 1)
• Four sets 0.250-28 x 0.625-inch stainless steel hex bolt with
split lock and flat washers (K in Figure 1)
• Four sets 12mm M4x0.7 Phillips stainless steel pan-head
screws with split lock and flat washers L in Figure 1)
• One external GPS antenna and cable, powered by 3.3VDC,
requires 150mA or less (M in Figure 1)
• One GPS antenna mounting bracket (N in Figure 1)
• Two sets 8mm M4x0.7 Phillips stainless steel pan-head
screws with split lock and flat washers (not shown)
• Three plastic cable ties (not shown)
Figure 1: AP field-installation package contents
A B C D E
I J K L
The field installation package can also include:
• Service level agreement/limited warranty statement
• Regulatory statement
• Registration card
• Declaration of conformity, if required
• 7782-E N-Type Connector Sealing Instructions
• This Mounting Guide
NOTE:
This kit can include extra screws, nuts and washers. You
may use the extras wherever required.
R H T
EQUIRED ARDWARE AND OOLS
• Customer-supplied external antennas, up to three 2.4GHz
and up to three 5GHz.
• Torque wrench or torque screwdriver with sockets and bits
• Long-nose pliers
• Narrow and wide flat-blade screwdrivers
• Electrical wire stripping and terminal crimping pliers
If you are mounting the AP on a flat surface, you will also need:
• Customer-supplied wall anchors rated to withstand 128 N or
28.8 lbf (required to withstand wind loads of 266km/h or
165mph)
• Electric drill with drill bits and customer-supplied wall anchors,
flat washers, and hex nuts for flat-surface mount
If you are mounting the AP on a pipe or pole, you will also need:
• A 30mm to 60mm (1.18" to 2.36") pipe or pole
• Four factory-supplied steel clamps
F G H
M N
Page 1 of 4