Fife CDP-01 Additional Instruction Manual
  1. Manuals
  2. Brands
  3. Fife Manuals
  4. Amplifier
  5. CDP-01
  6. Additional instruction manual

Fife CDP-01 Additional Instruction Manual

Armless recoiler application (fixed ratio)
Hide thumbs Also See for CDP-01:
Table of Contents

Advertisement

Quick Links

See also: Additional Instruction Manual
CDP-01
Additional Instruction Manual
For Armless Recoiler Application (Fixed Ratio)
CDP-01
DATE 10-31-97
Fig. Sheet 1-766

Advertisement

Table of Contents
loading

Related Manuals for Fife CDP-01

Summary of Contents for Fife CDP-01

  • Page 1 CDP-01 Additional Instruction Manual For Armless Recoiler Application (Fixed Ratio) CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 2 CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 3 These additional instructions explain the special features of the system delivered to the customer. They are intended for being used in conjunction with the CDP-01 Reference Manual. The CDP-01 Reference Manual applies except as noted to the contrary in these instructions.
  • Page 4 CDP-01 DATE 10-31-97 Fig. Sheet 1-766...

  • Page 5: Table Of Contents

    SPECIAL FEATURES OF EXTERNAL CONTROL..............2-1 INPUT MATRIX - EXTERNAL CONTROL ................2-2 EXPLANATION OF THE OPERATING MODES..............2-3 START UP / POSITION SENSOR CALIBRATION ..............2-6 START UP / GUIDING SENSOR CALIBRATION ..............2-8 TROUBLESHOOTING FAULT DIAGNOSIS - FAULT RECTIFICATION..............3-1 CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 6 CDP-01 DATE 10-31-97 Fig. Sheet 1-766...

  • Page 7: General Introduction

    Permissive input is high. Once the Auto Permissive input goes low, the sensor position and the mandrel position are read. The mandrel then follows the sensor positioner movements. A CDP-01-MHH is used for this application. Drive 1 is not used. The mandrel is connected to Drive 2 and the sensor positioner is connected to Drive 3.
  • Page 9 CDP-01 DATE 10-31-97 Fig. Sheet 1-766...

  • Page 11: Overview Of Function

    OVERVIEW OF FUNCTION Operator control options The CDP-01 signal amplifier can be operated by way of the CDP-01 control panel (internal operation) for setup purposes only. For normal operational control, the parallel port must be used. Control is to be supplied with a remote control panel or programmable logic controller.

  • Page 12: Input Matrix - External Control

    SUPPLEMENTARY OPERATING MANUAL Input Matrix - External control Inputs CDP-01 Modes External Lock (both drives) Automatic (seek, then guide) Auto Permissive (seek only) Manual (both drives) Retract Sensor / Center Mandrel Retract Sensor Only Jog Mandrel Left Jog Mandrel Right...

  • Page 13: Explanation Of The Operating Modes

    Setup functions and sensor modes can be selected. ‘Left’ Press the - or + key to set ‘Left’ or ‘Right’ to manually alter the position of the drive. ‘Right’ AUTOMATIC Select ‘Automatic’ via external control. CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 14 L H L L - The mandrel now follows the position of the sensor positioner. The guide point or system gain can be altered, if desired. Reference: CDP-01 Reference Manual, ‘Basic Settings’ section. RETRACT SENSOR / CENTER MANDREL Select ‘Retract Sensor / Center Mandrel’ via external control.

  • Page 15: Start Up / Position Sensor Calibration

    Select ‘Jog Sensor Out’ or ‘Jog Sensor In’ via external control to manually alter the position of the sensor. Note: Jogs are not allowed in Automatic mode Start-up / Position Sensor Calibration The following procedure must be performed while in Manual mode. CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 16 Press the F2 key. Press the Automatic key to store the settings. Press the Manual key to abort the procedure. Select Drive 3 by pressing key 20. Press the Sensor key repeatedly until LED 12 is lit. CDP-01 DATE 10-31-97 Fig. Sheet 1-766...

  • Page 17: Start Up / Guiding Sensor Calibration

    Press the F2 key. Press the Automatic key to store the settings. Press the Manual key to abort the procedure. Start-up / Guiding Sensor Calibration The following procedure must be performed while in Manual mode. CDP-01 DATE 10-31-97 Fig. Sheet 1-766...
  • Page 18 Press and hold the Left or Right Jog key until the sensor field of view is completely blocked by the web. Press the F2 key. Press the Automatic key to store the settings. Press the Manual key to abort the procedure. CDP-01 DATE 10-31-97 Fig. Sheet 1-766...

  • Page 19: Troubleshooting

    SUPPLEMENTARY OPERATING MANUAL TROUBLESHOOTING An incorrect setting on the CDP-01 is often the cause for incorrect or unwanted guiding characteristics. Faults and the procedures for rectifying the faults are described in more detail in the CDP-01 Reference Manual, chapter ‘Frequent setting errors’. Application-specific faults are explained below.

Table of Contents