Page 1
SERIAL NO. 1266 to Current WARNING All personnel shall carefully read, understand and follow all safety rules, operating instructions, and the Scaffold Industry Association’s MANUAL OF RESPONSIBILITIES of ANSI A92.6-1999 before performing maintenance on or operating any UpRight Aerial Work Platform. P/N 104044-001...
Page 2
Serial Numbers 1266 - Current When contacting UpRight for service or parts information, be sure to include the MODEL and SERIAL NUMBERS from the equipment nameplate. Should the nameplate be missing, the SERIAL NUMBER is also stamped on top of the chassis above the front axle pivot.
Page 3
• LOOK up, down and around for overhead obstructions and electrical conductors. • DISTRIBUTE all platform loads evenly on the platform. • NEVER use damaged equipment. (Contact UpRight for instructions. See toll free phone number on inside back cover.) • NEVER change operating or safety systems.
Introduction NTRODUCTION This manual covers the operation of the AB62 Articulated Boom. This manual must be stored on the machine at all times. ENERAL ESCRIPTION Figure 2: AB62 Work Platform 1. Platform • The platform has a non-slip alu- minum floor, guardrails with...
Lift the locking pin with the pin stop rod. b. insert the snap pin into the bottom hole. NOTE: Locking pins must be engaged for loading or unloading the machine onto a truck or trailer, and during transport. 104044-001 AB62 Work Platform - Operator Manual Page 5...
20. Press the Service Horn button. Observe that the horn is audible. W A R N I N G DO NOT use a machine that is damaged or malfunctioning. Tag and remove the unit from service until it is repaired. Page 6 104044-001 AB62 Work Platform - Operator Manual...
2. Turn platform controls key to the ON position. • Diesel: wait for the Glow Plug light to go off. 3. Turn the platform lever switch fully clockwise to crank the engine. Release when the engine starts. 104044-001 AB62 Work Platform - Operator Manual Page 7...
Travel with the boom elevated is restricted to firm, level surfaces only. When driving with the boom elevated or extended, the machine will travel at creep speed (0,3 m [1 ft.] per second). Page 8 104044-001 AB62 Work Platform - Operator Manual...
O N T R O L S The UpRight AB62 employs the use of multifunction controls. This means that the riser or boom extension will function at full speed while simultaneously operating the upper boom, jib, turret, or rotating the plat- form.
2. While depressing the foot switch, push the upper Boom control lever forward to elevate the upper boom, rearward to lower the upper boom. Release the control lever to stop elevating/lowering. Page 10 104044-001 AB62 Work Platform - Operator Manual...
2. If the engine stalls, check the following: • check the fuel supply in the selected tank. • if LPG is selected, make sure that the valve is open on the tanks. 3. Restart the engine. 104044-001 AB62 Work Platform - Operator Manual Page 11...
5. When ready to move the machine, remove the chocks. Tow or winch into position and replace the chocks. 6. Engage all four drive hubs by returning the center caps to their original orientation. Page 12 104044-001 AB62 Work Platform - Operator Manual...
(8 in. x 4 in. x 28 in.) floor grating, and over the support braces. Tighten securely; do not over- tighten. W A R N I N G NEVER elevate the machine while on a truck or trailer. 104044-001 AB62 Work Platform - Operator Manual Page 13...
• Extreme Temperature, below -17° C (0° F) ISO #15. 3. Clean the area around the cap before opening. Level Gauge 4. Open the filler/breather cap to add hydraulic fluid. 5. Install the cap. Page 14 104044-001 AB62 Work Platform - Operator Manual...
Always wear safety glasses when working with batteries. Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with clean water. Always replace batteries with UpRight batteries or manufacturer approved replacements weighing >28 kg (62 lbs.) each. Check battery fluid level daily.
Refer to the Service Manual for the Preventa- tive Maintenance Check List. Please photocopy the Daily Preventative Maintenance Check List and use the table as a checklist when inspecting the machine for service. Page 16 104044-001 AB62 Work Platform - Operator Manual...
Page 19
& replace Check fasteners for proper torque Check welds for cracks Platform Floor and Check condition of platform Rails Check condition of anchorage points Check condition of operator manual 104044-001 AB62 Work Platform - Operator Manual Page 17...
Page 21
Figure 12: Safety Labels Locations Both Sides Both Sides Both Sides Both Sides Both Sides Front & Rear Front & Rear Both Sides (Option) Both Sides Both Sides Front & Rear Front & Rear 104044-001 AB62 Work Platform - Operator Manual Page 19...
Perkins 704-30 – 63 HP System Voltage 12 VDC Maximum Hydraulic Pressure 345 bar [5000 PSI] Controls Electric Proportional Tires Size 19 x 15 NHS - 14 PLY Pressure 5,5 bar [80 PSI] Page 20 104044-001 AB62 Work Platform - Operator Manual...
Page 23
Call Toll Free in U.S.A. 1-800-926-LIFT...
Page 24
TEL: (1) 800-926-5438 or (1) 559-662-3900 FAX: (1) 559-673-6184 Parts FAX: (1) 800-669-9884 801 South Pine Street Madera, California 93637 http://www.upright.com UROPE TEL: +353 1 620 9300 FAX: +353 1 620 9301 Unit S1, Park West Industrial Park Friel Avenue...