Table of Contents
Advertisement
INsTAllING The dooR lIGhTING
1. Mount the Door Light Mounting Bracket (#5) to the gravity box using
5/16" x 1" Carriage bolt (#6), 5/16" Lock Washer (#7), and 5/16" Hex
nut (#8). Mount the Door Light (#5) to the Mounting Bracket (#5)
using a 5/16" x 2" bolt (#9), 5/16" Lockwasher (#7), and 5/16" Hex
Nut (#8). Items #5-#9 are included with Door Light #07436.
2. Insert a Light Mounting Grommet (#1) into each mounting hole.
Press in Red Lights (#2) and Amber Lights (#3) until they are
securely mounted in the grommets. Mount Inside Light Covers
(#17) using two 5/16" x 3/4" Bolts (#18)and two 5/16" Nylon Insert
Locknuts. (#16)
3. Secure the Light wire Cover (#4) using two 3/8" x 1" Bolts (#19)and
two 3/8" Nylon Insert Locknuts (#20) as shown.
hoT
AMbeR
TuRN / flAsh
Red
MARKeR
yelloW
bANd
GReeN
bANd
Red
MARKeR
AMbeR
TuRN / flAsh
lIGhT KIT PARTs bReAKdoWN ANd lIsT
7
8
8
5
7
6
5 9
20
21
19
To chuTe lIGhT
WIRING dIAGRAM
fRoNT/ReAR PluG
WhITe
11
(Ground)
Red
(chute)
yelloW
(left turn)
(open)
Plug pin location may vary
depending on tractor.
To ReAR PluG
18
20
20
4
1
3
20
4. Run the Wiring Harness (#10) under the right side of the gravity
box, inside wire cover. Secure the Light Harness to the frame using
the nylon hose ties. Attach Female Plug (#12) using two 5/16" x 1"
bolts (#14), two 5/16" washers (#15), and two 5/16" Nylon Insert
locknuts (#16) as shown. Proceed wiring the lights as shown in
the drawing and wiring schematic. Front of wagon has 1" O.D. hole
which the wiring harness passes through. Use 1" rubber grommet
Part # 04396 (not shown) to protect wires.
Ref. PART
No.
No.
1.
05447
15540
2.
3.
15541
4. 11024-30
*5.
07436
06925
*6.
*7.
00036
00007
*8.
*9.
04887
10.
03910
NhT21
-
11.
07416
07417
12.
bRoWN
13.
07418
(Tail lights)
02990
14.
15.
00004
02802
16.
17. 07388-30
GReeN
07387-30
-
(Right turn)
18.
01263
00907
19.
blue
20.
02592
(open)
21. 12443-30
* Included with chute light # 07436
Please order replacement parts by PART No., descRIPTIoN and coloR.
10
ReAR PluG
13
12
Page 22
18
1
16
1
2
12
15
13
15
14
lIGhTING PARTs lIsT
qTy.
descRIPTIoN
4
Light Mounting Grommet
2
4" Red Light
2
4" Amber Light
1
Light Wire Cover (chute light)
1
Door Light and Mount (use H3 bulb)
1
5/16"-18 UNC x 1" Carriage Bolt
2
5/16" Lockwasher
2
5/16"-18 UNC Hex Nut
1
5/16"-18 UNC x 2" Hex Head Bolt, Gr.5
1
Wire Harness (see lower diagram)
4
Nylon Hose Tie
1
7 Pin Male Plug (front)
1
7 Pin Female Plug (rear)
1
Female Plug/Wire Rubber Boot
2
5/16" - 18 UNC x 1" Hex Head Bolt
2
5/16" Flatwasher
6
5/16" - 18 UNC Nylon Insert Locknut
1
Inside Right Light/Wire Cover
1
Inside Left Light/Wire Cover (not shown)
4
5/16"-18 UNC x 3/4" Gr. 5
2
3/8"-16 UNC x 1" Gr. 5
2
3/8"-16 UNC Nylon Insert Locknut
1
Light Wire Cover
To fRoNT PluG
NoTe : Connect the wires to the tractor
plug in, make sure all lights are in correct
working order. When working correctly
behind a tractor the amber lights are
the flashing warning lights, and the
turn signals.
17
1
3
2
Hide quick links:
Advertisement
Table of Contents
