1. Manuals
  2. Brands
  3. The Wings Maker Manuals
  4. Toy
  5. SkyNova 2
  6. Instruction manual

The Wings Maker SkyNova 2 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Before commencing assembly please read these instructions thoroughly
Wing Span: 48.8 in / 1240 mm
Wing Area: 338 sq in / 21.8 sq dm
Flying Weight: 25.8 oz / 730 g
Fuselage Length: 33.8 in / 858 mm
Requires: 4-channel radio w/ 5 mini servos
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
.
www thewingsmaker com
GM082XMPO30231403
,
Specifications
Specifications
Outrunner Motor KM28251025 w/ Propeller Adaptor
HW2340100 20A Brushless ESC,9x6 Propeller,
3 cells 11.1V 1800 mAh Li-Po battery & charger.
.
I NSTRUCTI ON M ANUAL
( GM082XM )
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SkyNova 2 and is the answer not in the manual?

Questions and answers

Related Manuals for The Wings Maker SkyNova 2

Summary of Contents for The Wings Maker SkyNova 2

  • Page 1 Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. * Specifications are subject to change without notice.* THE WINGS MAKER FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA...

  • Page 2: Before You Begin

    INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY P.3-P.15 SAFETY PRECAUTIONS P.16 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.

  • Page 3: Parts List

    Parts List 1.DECALS: GM082XM DEC -- 1 set 10.MAIN LANDING GEAR Ø2.5mm -- 1 set MAIN WING -- 1 pair COLLAR Ø2.6mm w/ Set Screw -- 2 sets STABILIZER -- 1 set MAIN WHEEL Ø40mm PL3116040 -- 2 pcs FUSELAGE -- 1 set SCREW PA2.3x8mm -- 1 pc.
  • Page 4 Decals Cut out decal sheet, peel off backing sheet and apply on fuselage, stabilizer and wings. Decal Main wings Main wings Main wings Top View Top View Bottom View Bottom View Stabilizer Stabilizer Bottom View Bottom View Top View Top View Fuselage Left View Left View...

  • Page 5: Stabilizer & Elevator

    Stabilizer & Elevator Hinge Setting Hinge Section View Completed Hinge For pre-assembled version, the hinges are factory glued. Bottom View Vertical Fin & Rudder Hinge Setting Hinge Section View Completed Hinge For pre-assembled version, the hinges are factory glued. Right View Decals for Rudder Transparent decals to reinforce stabilizer.

  • Page 6: Rudder Pushrod

    Rudder Servo & Horn Plastic Bracket Servo wire For pre-assembled version, the horn is factory Horn glued and servo installed. Rudder Pushrod Straper Plastic Stand Fuel Tube d2xD4x4mm Pushrod Ø1.4x45mm Clevis Fuel Tube d2xD4x4mm Horn Elevator Servo & Horn Servo wire Plastic Bracket Horn For pre-assembled version, the horn is factory glued and servo installed.

  • Page 7: Elevator Pushrod

    Elevator Pushrod Plastic Stand Straper Pushrod Ø1.4x60mm Clevis Fuel Tube d2xD4x4mm Horn Tail Landing Gear PA2x8mm Screw Wheel Ø23mm PA2x8mm Plastic Collar 1.2mm Bottom View Main Landing Gear PA2.3x8mm Screw Plywood 21x26x2.5mm Fuselage PA2.3x8mm Landing Gear Wheel Ø40mm 3.1mm Collar M3x3mm Set Screw Landing Gear...

  • Page 8: Motor & Esc

    Motor & ESC M3x8mm Socket Head Screw d3xD7mm Washer M3x8mm 2-Pin EZ Connector d3xD7mm Washer EZ Connector Brushless ESC Motor KP0011310 Solder Solder Aileron Servo & Horn Hinge Setting Plastic Bracket Servo wire Hinge Section View Completed Horn Hinge Bottom View For pre-assembled version, the hinges and horn are pre-glued, and servo installed.
  • Page 9 Aileron Pushrod Fuel Tube d2xD4x4mm Straper Plastic Stand Fuel Tube d2xD4x4mm Clevis Pushrod Ø1.4x65mm Horn Bottom View Main Wing Nylon Bolt M3x20mm Wing Tube Ø6x715mm Servo wire Insert carbon fiber wing tube into right wing, align the anchor holes and apply the nylon bolt. Nylon Bolt M3x20mm Insert the right wing into the Fuselage.
  • Page 10 Radio 180mm Y-Cord Aileron Servo (L) Elevator Servo Aileron Servo (R) Rudder Servo Receiver Plug in the Aileron Servos wire to channel 1 Plug in the Elevator Servo wire to channel 2 Plug in the ESC Throttle wire to channel 3 Plug in the Rudder Servo wire to channel 4 Receiver Tie 130mm Radio...
  • Page 11 Battery & Motor Setting Battery Mat Pull throttle stick all the way back. Mode 1 Mode 2 Battery Tie 200mm Plug in battery wait a few seconds for the transmiter and receiver to bind. Black Black Plug in with red+ / black- reversed will damage the ESC. Battery KP0011210 Solder...
  • Page 12 Servos Setting Mode 1 Mode 2 Pull back Elevator stick Elevator should move up, plane will pull up when Pull back Elevator stick flying. Mode 1 Mode 2 Push foward Elevator stick Elevator should move down, plane will dive down Push foward Elevator stick when flying.
  • Page 13 Propeller Unplug battery EZ Connector Puller Switch off transmiter Charge battery The battery is ready for use when all the lights turn from red to green. Install the propeller Propeller Adaptor (d3xD5) HW2340100 PM2x12mm 9x6 Propeller PL6314050 M5 Nut Ø36mm Spinner PA1.7x8mm TWM HW3111400 PROPELLER ADAPTOR WRENCH...
  • Page 14 C.G. Install battery onto the battery tray. Don`t plug in the battery yet. Put on the battery check C.G. mark underneath wings. Support the model by two fingers on the C.G. mark, move battery position if necessary to balance the model on the C.G.

  • Page 15: Get Ready To Fly

    Get Ready to fly Turn on transwitter, throttle stick at low position. Mode 1 Mode 2 Plug in battery. Black Black Plug in with red+ / black- reversed will damage the ESC. Wait a few seconds for the receiver to bind with transmitter. Make sure the propeller is cleared of any object.
  • Page 16 Flying Try to get an experienced flyer to check through your installation before flying. Ask him/her to do the first flight for you. He/she can trim out the control surfaces for you so the model can fly straight and level with control sticks in neutral positions and throttle stick about half throttle. You will get a much higher successful rate with the help from an experienced flyer.

  • Page 17: Important Safety Precautions

    Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. is specially designed to be powered by KM28251025 Outrunner Motor.
  • Page 18 Pl8210010 Large Clevis Small Clevis Outrunner Motor KM28251025 180mm Y-Cord Code No. Size Package -Kv (rpm/V): 1025 KW0021800 180mm 1 pc -Operating Power: 110W -Operating Voltage: 2-3S Li-Po -Operating Current: 10A -Peak Current: 15A (max. 15 sec.) -Internal Resistance: 50 m ohms -Diameter: 27.6mm -Length: 25mm EZ Connector Puller...
  • Page 19 GM082XMPO30231403...
  • Page 20 THE WINGS MAKER GM082XMPO30231403...

This manual is also suitable for:

Gm082xm

Table of Contents