Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Linak DL15
Summary of Contents for Linak DL15
- Page 1 DL15/DL16 system User manual LINAK.COM/DESKLINE Page 1 of 28...
-
Page 2: Table Of Contents
® Mounting guidelines for the DESKLINE DL15/DL16 system ............11 ® Mounting guidelines for the DL15 (foot part) ................12 Mounting guidelines for the DL16 (foot part) ................12 Mounting of the desk (misc.) ...................... 13 Mounting guidelines CBD4/CBD5/CBD6 ................... 15 Electrical connection of the DL15/DL16 system ............... -
Page 3: Preface
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety information from this manual is passed on to the end-user. -
Page 4: Valid For
Valid for: This User Manual is valid for the following products: (See the first 3 - 5 characters on the label) Columns: DL15 / DL16 Control boxes: CBD4 / CBD5 / CBD6 Controls: DP1U / DPF1M (if memory function is required) -
Page 5: Important Information
Important information Important information on LINAK products can be found under the following ® headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. -
Page 6: Before Installation, Reinstallation Or Troubleshooting
• Stop the DL15/DL16 • Switch off the power supply and pull out the mains plug. • Relieve the DL15/DL16 of any loads, which may be released during the work. Before start-up: • Make sure that the system has been installed as instructed in this User Manual. -
Page 7: Only For Eu Markets
Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. -
Page 8: Repairs
Repairs In order to avoid the risk of malfunction, all DESKLINE repairs must only be carried out by authorised LINAK workshops or ® repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned to authorised LINAK workshops. -
Page 9: Misc. On The Deskline ® Dl15/Dl16 System
Misc. on the DESKLINE DL15/DL16 system ® This system is a DESKLINE system developed for desks and for indoor use in offices. Do not use it in industrial kitchens or in other environments that have to be cleaned with aggressive detergents. -
Page 10: Description Of The Deskline ® Dl15/Dl16 System
® Each DESKLINE DL15/DL16 lifting unit is equipped with a motor and parallel/memory drive is ensured by means of software ® in the CBD4/CBD5/CBD6 that also takes account of oblique load on the desk. Soft start and stop are also part of this software, which ensures a soft start and stop when adjusting the desk. -
Page 11: Mounting Guidelines For The Deskline Dl15/Dl16 System
Mounting guidelines for the DESKLINE DL15/DL16 system The lifting units are normally mounted with the motor housings upwards and pointing towards each other. The steel motor housing is supplied with 6 pcs. of M6 threaded holes meant for mounting on the desk frame. -
Page 12: Mounting Guidelines For The Dl15 (Foot Part)
Mounting guidelines for the DL15 (foot part) The DL15 is supplied with 4 threaded holes M6 for mounting of the foot. We advise you to fasten the foot by means of 4 screws M6 of a good quality (min. 8.8) and of a suitable length. M6 screws must not go further than 20 mm into the DL15 column. -
Page 13: Mounting Of The Desk (Misc.)
Mounting of the desk (misc.) A suitable desk height in the lowest position can be obtained by mounting the lifting unit on a 6-8 mm bottom plate by means of 4 pcs. of M6 countersinked screws. We recommend you to use screws of min. quality 8.8. The thrust moment must not exceed 10 Nm in the bottom plate thread. - Page 14 This will result in an irregular operation or even damage the lifting unit. The DESKLINE DL15/DL16 system can only be used in push applications with the motor housing mounted upwards. ® Placement of a monitor directly above the motor housing may cause malfunction of the monitor. Magnets inside the motor may interrupt the picture on the monitor depending on the distance and type of monitor.
-
Page 15: Mounting Guidelines Cbd4/Cbd5/Cbd6
Mounting guidelines CBD4/CBD5/CBD6 The control box is to be fastened with 4 screws (3 screws for CBD5 and CBD6) with a head diameter between ø 8 and ø 10 mm. Out of regard for the tension surface ø 10 mm is preferable due to lower surface tension. See drawing appendix for placing of mounting holes and the space the CBD takes up. -
Page 16: Electrical Connection Of The Dl15/Dl16 System
DL15/DL16 system is to be connected as shown on figure 4. ® Each DL15/DL16 is to be connected to the sockets on the control box by means of the motor cables, which have an 6-pin plug in each end. Finally, the mains cable is to be mounted and power switched on. -
Page 17: Initialisation Of The Deskline ® Dl15/Dl16 Parallel System
NEW PICTURE Approx. 5 mm The CBD5 and CBD6 can control DL15 and DL16 in 2 parallel while the CBD4 can control DL15 and DL16 in 2, 3, and 4 parallel so that the desk is always kept horisontal. Page 17 of 28... -
Page 18: Accessories And Repair
Accessories Please contact your nearest LINAK dealer for information. Repairs Systems should only be repaired by an authorised LINAK service centre or engineer. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. Warning! By unauthorised opening of the system there is a risk that it may malfunction at a later date. -
Page 19: Disposal Of Linak Products
Disposal of LINAK’s products As LINAK’s customers often ask us how our products can be disposed or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend our products to be disassembled as much as possible and divided into different waste groups for recycling or combustion. -
Page 20: Labels
Labels Label for DL16 Label for DL15 Label for CBD4 Label for CBD5 Label for CBD6 Page 20 of 28... -
Page 21: Drawing Appendix
DRAWING APPENDIX Drawing No.: DL15_STANDARD Drawing No.: DL15_STANDARD DL15 lifting unit 1145 3 645 2 4xM6 4xM6 2xM6 Page 21 of 28... - Page 22 DL16 lifting unit Drawing No.: STANDARD_DL16 Drawing No.: STANDARD_DL16 1210 3 560 2 4xM6 4xM6 2xM6 Page 22 of 28...
- Page 23 Drawing No.: DL16XL_STANDARD Drawing No.: DL16XL_STANDARD DL16 XL 1710 730 5 4xM6 4xM6 2xM6 Page 23 of 28...
- Page 24 CBD4 CBD5 Page 24 of 28...
- Page 25 CBD6 Page 25 of 28...
-
Page 26: Declaration Of Confirmity
Page 26 of 28... - Page 27 LINAK customer using any LINAK product. LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.
-
Page 28: Addresses
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK.
Need help?
Do you have a question about the DL15 and is the answer not in the manual?
Questions and answers