Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hubsan H122D
Summary of Contents for Hubsan H122D
- Page 1 ® H122D X4 STORM 《H122D Quick Start Guide》 Version 1.0...
- Page 2 The first flight configuration: Aircraft + HT015 Transmitter Step 1 Binding the aircraft and transmitter 1 . Pull and hold the throttle to its lowest position. 2．Hold down the Photo key and power the transmitter on. The transmitter’s status LED will flash red; please do not press or touch any other keys, buttons or sticks while this process is ongoing.
- Page 3 plane during flight. When this happens, land the aircraft and disarm its motors. Follow the below steps to do a horizontal/gyro calibration. 1) Place the aircraft on a completely flat surface and then follow the below calibration procedure. Hold the left stick to the right side of its socket. Rapidly and continuously wiggle the right stick left and right until the rear red LEDS flash alternately.
- Page 4 Step 3 Takeoff Simultaneously pull the transmitter joysticks diagonally down-out to arm the motors (as shown in the left figure). Pull the left joystick (throttle) upwards to take off. Landing Slowly and gently pull the throttle joystick down until the copter has completed its descent on the ground.
- Page 5 The second flight configuration: Aircraft + HS001+ HT015 Transmitter+HV002 Video glasses Step 1 Binding the aircraft and transmitter 1. Pull and hold the throttle to its lowest position. Hold down the Photo key and power the transmitter on; allow the transmitter to enter binding mode. All illustrations are shown in Mode 2 (American hand) 2.
- Page 6 3. Connect the drone to its battery. While all units are in either binding or pairing modes, please do not touch, press or move any of the transmitter joysticks, buttons or keys. Doing so will cause the aircraft to drift or perform unstably during flight.
- Page 7 When using the horizontal calibration, please ensure that the aircraft is on a completely flat surface. Aircraft motors should be completely disarmed. Do not move the aircraft during calibration or calibrate on an uneven/tilted surface, or there will be errors. Step 3 Installing the HS001 display Option 1: Secure the HS001...
- Page 8 Step 4 Takeoff Simultaneously pull the transmitter joysticks diagonally down-out to arm the motors (as shown in the left figure). Pull the left joystick (throttle) upwards to take off. Landing Slowly and gently pull the throttle joystick down until the copter has completed its descent on the ground.
- Page 9 Getting to know your H122D Thank you for purchasing a HUBSAN product. The H122D is an easy to fly racing aircraft, paired with a multifunctional remote control. 5.8G antenna LiPo battery Aircraft head Battery strap Camera Head Aircraft Propeller A...
- Page 10 Getting to know your HT015 Battery compartment Photo key Aileron trim Video key Mobile Device frame Joystick Joystick Power button Headlight power toggle Clear Screen key Transmitter status LED Binding status LED HT015 low power status LED Getting to know your HS001 Micro-SD Power switch charging port...
- Page 11 5.8 Antenna Charging status LED Photo/Video mode switch button Photo/Video button LCD screen Main Menu Binding/Clear screen button Sunshade Speaker recess Getting to know your HV002 Face panel release...
- Page 12 Installing and removing propellers Propeller B Propeller A Propeller A Propeller B Installation: Before installing propellers for the first time, please check that each Propeller A is matched with motor A and each Propeller B is matched with motor B. Align the "I" with the flat side of the "D" shaped motor shaft.
- Page 13 “D” Shaft < F i g u r e 1 > Installation Removal Counterclockwise Clockwise to to install remove Counterclockwise Clockwise to to remove install Note: Mind the differing colors of the A and B propeller screws!
- Page 14 Charging and Installing the Aircraft battery The H122D aircraft is paired with a rechargeable 7.6v, 710mAh Li-Po. Be sure to use the provided Hubsan dedicated charger for charging. Fully charge the battery before flight. Connect the charger’s USB adapter to a PC terminal and then the battery to the charger.
- Page 15 Frequently Asked Questions 1. Aircraft and remote control are not pairing (1) Check that the aircraft and remote control are both powered on. (2) Turn off both the aircraft and remote control. Rebind the aircraft to the remote control by following the rebind directions on page 1 of this guide. 2.
- Page 16 This is not a toy, not suitable for children under 14. www.HUBSA N . co m Product Name：X4 STAR PRO Company：Shenzhen Hubsan Technology Co., Ltd. Address：13th Floor, Block 1, Tower C, Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China.