Table of Contents
Advertisement
Quick Links
THANK YOU!
We are grateful for your purchase of HYT product. We believe this easy–to-use
radio will provide you with clear and reliable communications in high efficiency.
This HYT portable two-way radio is a precision device. Treat it with care, and
you will enjoy years of reliable operation.
MODELS COVERED IN THIS MANUAL
TC700 VHF Two-way Radio
TC700 UHF Two-way Radio
1
Advertisement
Table of Contents
Related Manuals for HYT TC700
Summary of Contents for HYT TC700
- Page 1 We are grateful for your purchase of HYT product. We believe this easy–to-use radio will provide you with clear and reliable communications in high efficiency. This HYT portable two-way radio is a precision device. Treat it with care, and you will enjoy years of reliable operation.
-
Page 2: Table Of Contents
Contents User Safety, Training, and General Information Compliance with RF Energy Exposure Standards FCC Compliance Precautions Product Inspection Battery Information Accessory Installation Attaching/Removing the Battery Attaching/Removing the Antenna Attaching/Removing the Belt Clip Attaching Remote Earphone/Microphone Getting Acquainted Programmable Auxiliary Functions Basic Operation Advanced Operations Auto Dial... - Page 3 Communication Range Alarm Background Operations Time-out Timer (TOT) Busy Channel Lockout (BCL) and Busy Tone Lockout (BTL) Battery Save Low Battery Alert CTCSS/DCS DTMF 2-Tone/5-Tone Signaling Control PTT ID Troubleshooting Guide Care and Cleaning Optional Accessories Frequency Chart...
-
Page 4: User Safety, Training, And General Information
BEFORE USING YOUR HYT PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your HYT two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. -
Page 5: Fcc Compliance
Use of non- HYT -approved batteries may exceed FCC RF exposure guidelines. Approved Accessories For a list of HYT approved accessories, see the accessories page of this user manual or visit the following website which lists approved accessories: http://www.HYT.com.cn FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to FCC Rules. -
Page 6: Precautions
FCC Licensing Requirements Your radio must be properly licensed Federal Communications Commission prior to use. Your HYT Wireless dealer can assist you in meeting these requirements. Your dealer will program each radio with your authorized frequencies, signaling codes, etc., and will be there to meet your communications needs as your system expands. -
Page 7: Product Inspection
Product Inspection Please carefully unpack the radio. Before use, it is recommended that you inspect the product as follows. First check the shipping carton for any signs of damage. Confirm the supplied product against the packing slip to assure accuracy. If any items are missing or have been damaged during shipment, please file a claim to the carrier immediately. -
Page 8: Battery Information
Battery Information Battery Charging Information The battery is not charged at the factory. Batteries must be fully charged before initial use or if they have not been used for some period of time. The battery capacity will be optimum only after being charged/discharged for two or three times. When the battery power is low, it either needs to be charged or replaced with a new one. -
Page 9: Charging The Battery
When radio LED flashes red and three Beeps sound within 30 seconds after the battery is installed, that means battery power is low. Please charge the battery. You are recommended to use HYT-approved, supplied charger; Charger LED will indicate the charging status. - Page 10 Fig. 4 5. Make sure the battery is well connected with the charger connectors; when charging starts, the red LED glows. 5. The green LED glows when the battery is fully charged in about 3 hours, please remove the battery or the radio with battery from the charger. *Notes: *Charger LED may flash if you connect the charger to power source before inserting the battery.
-
Page 11: Accessory Installation
Accessory Installation Attaching the Battery Push the battery along the guide on back of the radio until the battery latch at the bottom of the radio locks. Removing the Battery 1. Turn off the radio. 2. Pull back the battery latch. 3. -
Page 12: Getting Acquainted
Getting Acquainted (1) PTT Key ●To transmit, hold down the PTT key and speak into the microphone; Release it to receive. (2) SK1 (Side Key 1) ●Programmable key (3) SK2 (Side Key 2) ●Programmable key (4) Antenna (5) Microphone (6) Speaker (7) TK (Top Key) ●Programmable key (8) Channel Selector Knob... - Page 13 the volume. (10) LED Indicator Radio status is indicated by LED state/color or alert tone. Indication LED State/Color Alert Tone Power on Flash orange twice Source radio during Solidly glow red User Wired Clone Mode cloning Target radio during Solidly glow green cloning Power on Flash orange three times...
- Page 14 three Beeps Enter one Beep Programmable Key Exit two Beeps (11) Speaker/Microphone Jack (12) Belt Clip (13) Battery (14) Screws (belt clip) (15) Battery Latch...
-
Page 15: Programmable Auxiliary Functions
Programmable Auxiliary Functions Your dealer can program each of the TK, SK1, SK2 keys with one of the following auxiliary functions. Please refer to their descriptions in “Advanced Operation”. ● None (No Function) Call1/Call2 ● ● Emergency ● Emergency Cancel ●... -
Page 16: Basic Operation
Basic Operation 1. Turn On the Radio: Rotate the Power/Volume Control knob clockwise until green LED flashes one time. ● A BEEP sounds if alert tone is set your dealer. 2. Monitor: press the preprogrammed MONI key or SQ OFF key to hear background noise, then turn the Power/Volume Control knob to adjust the volume. -
Page 17: Advanced Operations
Advanced Operations The following functions are programmable by your dealer, as described above. Auto Dial Press the preprogrammed Call1/Call2 key to transmit the stored DTMF code, 2-tone /5-tone code. Emergency Program the programmable key (TK) with emergency feature. When activated, the emergency feature enables the radio to emit emergency alarm or send ENI (Emergency Number Identity) / background tone to companions or system (as selected by user via... -
Page 18: Monitor/Squelch Off
Monitor/Squelch Off ● Monitor Toggle Press the preprogrammed Monitor Toggle key to enable the signaling squelch feature; press it again to exit. ● Monitor Momentary Press and hold the Monitor Momentary key to enable the signaling squelch feature; release it to exit. ●... -
Page 19: Sql Check & Adjust
radio exits from Scan mode or restarts. ■ You cannot delete the priority channel, if one has been set. ■ You cannot delete a channel if there will be less than 2 channels available for scanning. SQL Check & Adjust Program one of the programmable keys with this feature;... -
Page 20: Whisper
Press and hold the preprogrammed key, Beep tone corresponds to power level, a Beep indicates Low power; two Beeps indicate Middle power and three Beeps indicate High power. Briefly press the key to adjust the power level; Power will be increased by one level and setting is saved each time when you press the key. -
Page 21: Background Operations
Background Operations Time-Out-Timer (TOT) Time-Out-Timer is used to prevent someone from using the same channel for a long time. If the transmission exceeds the time preset by your dealer (default is 1 minute), transmission will stop and an alert tone will sound. To stop the alert tone, release the PTT key. - Page 22 Low Battery Alert Low Battery Alert alerts you to recharge or replace the battery. When the battery voltage becomes low, radio LED will flash red and three Beeps sound within 30 seconds, indicating to recharge or replace the battery with a new one. CTCSS/DCS When CTCSS/DCS...
- Page 23 ● LED glows green in decode mode, and flashes orange for a preset period of time after successful decoding. Signaling Control CTCSS/DCS AND 2-Tone/5-Tone: If both signalings are employed, the squelch feature is only opened when both match. CTCSS/DCS OR 2-Tone/5-Tone: If both signalings are employed, the squelch feature is opened when either matches.
-
Page 24: Troubleshooting Guide
Troubleshooting Guide Trouble Solution *Battery may be used up. Please recharge or replace the No power battery. *The battery may not be properly installed. Remove the battery and attach it again. Power doesn't last long even if fully *Battery life is over, please replace it with a new one. charged Can't talk to or hear group members *Make sure you are using the same frequency and same... -
Page 25: Optional Accessories
HYT endeavors to achieve the accuracy and completeness of this manual, but cannot guarantee its accuracy at all times. All the above specifications and design are subject to change by HYT without notice. All the reproduction and translation of this manual without authorization of HYT is not allowed.