Page 1
Weather Station · Meteo THBM Colour Instruction manual...
Page 2
Desidera ricevere informazioni esaustive su questo prodotto in una lingua specifica? Venga a visitare il nostro sito Web al seguente link (codice QR Code) per conoscere le versioni disponibili. www.bresser.de/P7007900000000 GARANTIE · WARRANTY · GARANTÍA · GARANZIA www.bresser.de/warranty_terms...
Page 5
• Disconnect the device from the power supply by pulling the power plug when it is not used or in case of longer interruption of operation and before starting any work on maintenance and cleaning. • Position your device so that it can be disconnected from the power supply at any time. The power socket should be installed near the device and should be easily accessible as the mains cable plug is used to disconnect the device from the power supply.
NOTICE Risk of voltage damage! The manufacturer is not liable for voltage damage due to improperly inserted batteries or through the use of an improper power adapter! 5 Parts overview and scope of delivery Illustration 1: Parts overview for base station (top) and remote sensor (bottom) 1 TIME SET button (manual time/date setting 2 ALARM button (set alarm and enable/disable and user defined settings)
7 INDEX button (display change between dew 8 Display point and heat index) 9 Wall mount 10 Wall mount adapter 11 °C/°F button (display change between °C or 12 RESET button (reset all settings) °F) 13 BARO button (display change between hPa, 14 Display brightness: bright (HI), low (LO) or InHg or mmHG as well as barometric pressure automatic (AUTO)
8 Setting up power supply Base device 1. Insert the DC connector into the connection socket of the base station. 2. Insert the mains plug into the power outlet. 3. The device is energized directly. 4. Wait until the indoor temperature is displayed on the base station. NOTICE! For permanent operation, mains power supply is recommended.
6. Finally press the TIME SET button to save the settings and exit the setting mode. 11 Alarm setting 1. Press and hold ALARM button for approx. 3 seconds to enter the alarm time setting mode. 2. Digits to be set are flashing. 3.
1. Press the ALERT button for approx. 2 seconds and the current channel symbol starts flashing. 2. Press the +/CH- or -/MEM button to select IN (indoor) or CHANNEL 1-8. 3. Press ALERT button to confirm and continue to the next setting. 4.
Illustration 3: Moon phases for the northern hemispere. 1 New moon 2 Waxing crescent 3 First quarter 4 Waxing gibbous 5 Full moon 6 Waning gibbous 7 Third quarter 8 Waning crescent 18 Weather Trend The weather station will calculate a weather trend for the next 12 hours on basis of the measured val- ues.
4. Press the BARO button again, and the number for RELATIVE flashes. 5. Press UP or DOWN button to change the value. 6. Press the BARO button to save and exit the setting mode. NOTE 1. The default relative atmospheric pressure value is 1013 mb/hPa (29.91 inHg), which refers to the average atmospheric pressure.
25 EC Declaration of Conformity Hereby, Bresser GmbH declares that the equipment type with part number: 7007900000000 is in compliance with Directive: 2014/30/EU.The full text of the EU declaration of conformity is available at the following internet address: http://www.bresser.de...
The regular warranty period is two years and starts on the day of purchase. To take advantage of the extended, voluntary warranty period specified on the presentation box, you must register on our web- site. Please see http://archive.bresser.de/download/warranty_terms/warranty_terms.pdf for all of the warranty conditions as well as information about extended warranties and services. 16 / 20...
Page 20
Teléfono*: +34 91 67972 69 Telephone*: +44 1342 837 098 BRESSER UK Ltd BRESSER Iberia SLU c/Valdemorillo,1 Nave B Unit 1 starborough Farm, P.I. Ventorro del cano Starborough Road, Nr Marsh Green, Edenbridge, Kent TN8 5RB 28925 Alcorcón Madrid...
Need help?
Do you have a question about the Meteo THBM Colour and is the answer not in the manual?
Questions and answers