Canon H1 Service Manual page 50

4
Parts Replacement and Cleaning Procedure > Original Exposure System (Reader) > Removing the CCD Unit
<Processing after replacing the parts>
NOTE:
The EEPROM on the CCD PCB memorizes the reader-related service mode.
The CCD unit of the service part is supplied in the state that adjustment value was
written.
1.If uploading of backup data succeeds before replacement
1) Restoring the backup data
(Lv.2) COPIER>FUNCTION>SYSTEM>RSRAMRES
2) Input the service label value packaged in the service parts content.
COPIER> ADJUST> CCD>
3) Enter the value written in the service label inside the reader rear cover.
COPIER> ADJUST> ADJ-XY>
FEEDER> ADJUST>
COPIER> ADJUST> PASCAL>
4 Parts Replacement and Cleaning Procedure > Original Exposure System (Reader) > Removing the CCD Unit
(Lv.1) MTF3-M1
(Lv.1) MTF3-M2
(Lv.1) MTF3-M3
(Lv.1) MTF3-M4
(Lv.1) MTF3-M5
(Lv.1) MTF3-M6
(Lv.1) MTF3-M7
(Lv.1) MTF3-M8
(Lv.1) MTF3-M9
(Lv.1) 100-RG
(Lv.1) 100-GB
(Lv.1) 50-RG
(Lv.1) 50-GB
(Lv.1) 100-RG-2
(Lv.1) 100-GB-2
(Lv.1) 50-RG-2
(Lv.1) 50-GB-2
(Lv.1) 100-RG-3
(Lv.1) 100-GB-3
(Lv.1) 50-RG-3
(Lv.1) 50-GB-3
T-4-3
(Lv.1) ADJ-X
(Lv.1) ADJ-Y
(Lv.1) ADJ-S
(Lv.1) ADJ-X-MG
(Lv.1) ADJ-Y-DF
(Lv.1) STRD-POS
(Lv.1) DOCST
(Lv.1) LA-SPEED
(Lv.1)
OFST-P-K
COPIER> ADJUST> CCD>
4) Make an output of P-PRINT.
(Lv.1) COPIER > FUNCTION > MISC-P > P-PRINT
5) Store the outputted P-PRINT into the service book.
6) After turning OFF/ON the power, make a copy and check the copied image.
4-8
(Lv.1) MTF3-M1
(Lv.1) MTF3-M2
(Lv.1) MTF3-M3
(Lv.1) MTF3-M4
(Lv.1) MTF3-M5
(Lv.1) MTF3-M6
(Lv.1) MTF3-M7
(Lv.1) MTF3-M8
(Lv.1) MTF3-M9
(Lv.1) 100-RG
(Lv.1) 100-GB
(Lv.1) 50-RG
(Lv.1) 50-GB
(Lv.1) 100DF-RG
(Lv.1) 100DF-GB
(Lv.1) 50DF-RG
(Lv.1) 50DF-GB
(Lv.1) 100-RG-2
(Lv.1) 100-GB-2
(Lv.1) 50-RG-2
(Lv.1) 50-GB-2
(Lv.1) 100-RG-3
(Lv.1) 100-GB-3
(Lv.1) 50-RG-3
(Lv.1) 50-GB-3
(Lv.1) W-PLT-X
(Lv.1) W-PLT-Y
(Lv.1) W-PLT-Z
T-4-4
4-8