Table of Contents
Advertisement
Quick Links
HYDROMATIC
HPGX200/HPGLX200
Explosion Proof Submersible
Grinder Pumps
(Class I, Division 1, Group C & D): FM
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equipment or to
the responsible party who maintains the system.
Pump Installation and Service Manual
®
Advertisement
Table of Contents
Related Manuals for Hydromatic HPGLX200
Summary of Contents for Hydromatic HPGLX200
- Page 1 Pump Installation and Service Manual HYDROMATIC ® HPGX200/HPGLX200 Explosion Proof Submersible Grinder Pumps (Class I, Division 1, Group C & D): FM NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equipment or to...
-
Page 2: General Information
3 septic sump. months or longer and prior to electrical startup. Thank you for purchasing your Pump: HYDROMATIC Pump. To help Seal Failure Probes: The explosion proof submersible ensure years of trouble-free pump family was designed in All explosion-proof submersible... -
Page 3: Pump Installation
Overload Heaters: 230V (DUAL VOLTAGE) THREE PHASE can be furnished for mounting to WHITE BLACK If the HYDROMATIC electrical P1 (PURPLE) walls of basin. In either case, P2 (DARK BROWN) panel is not used, starters with be sure the HYDROMATIC... -
Page 4: Pump Operations
Heat Sensor and Seal Pump Failure Connections: 1. If pump is 3 phase, the rotation Maintenance If a HYDROMATIC control panel of the impeller must first be is used, terminal blocks are checked. Lift pump from provided for heat sensor and seal... - Page 5 Disconnecting Pump Cords: to ensure parts are not rubbing. pump discharge. If a HYDROMATIC explosion 2. Turn off circuit breaker. proof pump is to be removed from Replacing Seals: its location, the pump cords may 1. Remove pipe plugs (11) from...
- Page 6 7. Use only HYDROMATIC come in contact with the rotor. submersible oil in motor Replace power cord chamber and seal chamber. In...
-
Page 7: Pump Troubleshooting
Pump is noisy If the cause of the trouble cannot Pump be determined and corrected as 1. Defective bearings Troubleshooting outlined above, contact your 2. No axial clearance between nearest factory representative. impeller and volute 3. No axial clearance between Below is a list of troubles and radial cutter and cutter ring their probable causes. -
Page 8: Parts List
HPGX200 Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions. - Page 9 HPGX200...
- Page 10 HPGLX200 Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions.
- Page 11 HPGLX200...
-
Page 12: Warranty
All dual seal non-clogs and 2 HP grinders must have seal failure and heat sensors attached and functional for Warranty to be in effect. If a seal failure should occur, Hydromatic Pumps will cover only the lower seal and labor thereof. Labor based on Authorized Service Center contract allowance. If the heat sensor is not attached and functional, Warranty is void.
Need help?
Do you have a question about the HPGLX200 and is the answer not in the manual?
Questions and answers