Test Operation - Panasonic S-200PE2E5 Technical Data & Service Manual

2. Wireless Remote Controller
4. Setting Address Switches
 Main/Sub setting
Remove the top case of the receiver for setting.
Switch
1 2 3 4
 When more than 1 receiver is installed in the same room, setting addresses prevents interference.
 For how to change addresses of wireless remote controllers, see operating instructions of wireless remote controllers.
Address
Wireless
remote controller
address display
Receiving is
Address
possible at all
switch position
address positions.

5. Test operation

Preparation : Turn on the circuit breaker of units and then turn the power on. After the power is turned on, remote controller operation is ignored
for approx. 1 minute because setting is being made. This is not malfunction. (Contents received while setting are disabled.)
1. To start test operation, press and hold the emergency operation button for 10 seconds.
2. The indication lamps (OPERATION, TIMER, STANDBY) blink during test operation.
. 3 T o f n i s i h e t t s o p r e t a o i , n
Attention
 Do not use this mode for purposes other than the test operation.
(To prevent overload of the units)
 Read the installation instructions supplied with the units.
 Any of the Heat, Cool and Fan operations can only be performed.
 The "Alarm Display" as shown in the table below expresses the alarm contents displayed when the wired remote controller is connected. For
how to handle the alarms, see installation instructions of indoor units or technical guide.
Communication error in the remote controller circuit
Communication error either in the in/outdoor operation line or
the sub-bus of the outdoor unit
Operation of indoor protection device
O p r e t a o i n f o o u d t o r o p o r e t
E r r r o n i h t e n i d o r o h t r e m t s i
E r r r o n i h t e o u d t o r o h t r e m
E r r r o n i h t e n i d o r o E E P R O
E r r r o n i h t e o u d t o r o E E P R
E r r r o e r a l e t d o t h t e c o m p e r
E r r r o n i n i d o r o s e t t n i g s
E r r r o n i o u d t o r o s e t t n i g s
Inconsistency in Air/Heat (Including an auto-temp setting
for a model without auto-temp settings)
Oil Alarm (Same as operation of outdoor protection device)
Test operation
AMP Air Conditioning
 Address setting
 Use this to set Main/Sub for the remote controller and the receiver.
 Set one to [Main] and the other to [Sub].
 Factory default: [Main]
 It is recommended to set the wired remote controller to [Main].
OFF ON
M
Main/Sub switch position
Address Address
ALL 1
1 2 3 4 1 2 3 4
p e r s s a n d h o d l h t e e m e g r e n y c o
Self-diagnostics table and detected contents
D e e t c e t d c o n e t n s t
t c o i n d e v c i e
r o
t s i r o
M
O M
s s r o
Main/Sub setting
a n i S / u b
Address setting
Address Address
2 3
1 2 3 4 1 2 3 4
p r e t a o i n b t u o t n f r o 1 0 s e c o n d . s
 Temperature cannot be changed.
 The test operation mode is automatically turned off in 60 minutes.
(To prevent continuous test operation)
 Outdoor units do not operate for approx. 3 minutes after the power is
turned on or operation is stopped.
Alarm Display
E01–E03, E08–E14, E17, E18
E04–E07, E15, E16, E19–E31
P01, P09–P14
P 0 2 – P 0 , 8 P 1 5 – P 3 1
F 0 1 – F 0 , 3 F 1 0 – F 1 1
F 0 4 – F 0 , 9 F 1 2 – F 2 8
F 2 9
F 3 , 0 F 3 1
H 0 1 – H 3 1
L 0 1 – L 0 , 3 L 0 5 – L 0 9
L 0 , 4 L 1 0 – L 3 1
: OFF : ON (Illuminated) : Blinking (0.5 seconds interval)
8-19
www.ampair.co.uk | sales@ampair.co.uk
Control of 2WAY SYSTEM
M A N I S U
1 2 3 4 1 2 3 4
Address Address
4 5 6
1 2 3 4 1 2 3 4
n I d c i t a o i n a l m p o n h t e e r
OPERATION TIMER STANDBY
  
  
  
  
  
  
  
  
  
  
  
  
  
  
B
c e v i r e
Blinking
Alternately
Alternately
Alternately
Alternately 8
Simultaneously
Simultaneously
Simultaneously
Simultaneously
Alternately
Alternately
Simultaneously