Related Manuals for KYLAND Technology Opal5 series
Summary of Contents for KYLAND Technology Opal5 series
- Page 1 Opal5/Opal8 Series Entry-Level Industrial Ethernet Switch Hardware Installation Manual Publication Date: 2016-06-29 Version: V1.3 No.: 112023031...
- Page 2 Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery. Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as accurate and as updated as possible. This document is not guaranteed to be error-free, and we reserve the right to amend it without notice to users.
- Page 3 Notice for Safety Operation The product performs reliably as long as it is used according to the guidance. Artificial damage or destruction of the device should be avoided. Before using the device, read this notice carefully for personal and equipment safety. Please keep the manual for further reference.
- Page 4 In the following cases, please immediately shut down your power supply and contact your Kyland representative: ● Water gets into the equipment. ● Equipment damage or shell damage. ● Equipment operation or performance has abnormally changed. ● The equipment emits odor, smoke or abnormal noise. Note：The security of any system merged with this device is the responsibility of the assembler.
- Page 5 Contents 1 Product Overview…………………………………………………………………1 2 Structure and Interface……………………………………………………………3 2.1 Front Panel……………………………………………………………………3 2.2 Top Panel……………………………………………………………………4 3 Mounting……………………………………………………………………………4 3.1 Dimension Drawing…………………………………………………………4 3.2 Mounting Modes and Steps…………………………………………………5 3.2.1 DIN-Rail Mounting………………………………………………………5 3.2.2 DIN-Rail Dismounting…………………………………………………6 4 Connection…………………………………………………………………………6 4.1 10/100Base-T(X) Ethernet Port……………………………………………6 4.2 100Base-FX Ethernet Port…………………………………………………8 4.3 100Base-X SFP Slot………………………………………………………8 4.4 Grounding………………………………………………………………10 4.5 Power Terminal Block………………...
-
Page 6: Product Overview
1 Product Overview Opal5/Opal8entry-level industrial Ethernet switches are specially designed for industrial control applications. Opal5/Opal8 supports normal-temperature-range and wide-temperature-range models. Broadcast storm protectioncan be configured through DIP switch. The series switches support DIN rail mounting.Opal5 provides four 10/100Base-T (X) Ethernet ports, one 100M copper or fiber (optional); Opal8 provides six 10/100Base-T(X) Ethernet ports, two 100M copper or fiber (optional). - Page 7 Table 2 Opal8 Models Note: We reserve the right to amend the product information listed in this table without notice. To obtain the latest information, you can contact our sales or technical support personnel. Kyland Opal5/Opal8 IM-EN-June 2016...
-
Page 8: Front Panel
2 Structure and Interface Caution: It is recommended to purchase the port dustproof shield (optional) to keep ports clean and ensure switch performance. 2.1 Front Panel (1 ) (1 ) (1 ) (1 ) (2 ) (2 ) (2 ) (2 ) (3 ) (3 ) -
Page 9: Top Panel
2.2 Top Panel Grounding Grounding screw screw Power Power terminal terminal block block switches switches Figure 2 Top Panel 3 Mounting 3.1 Dimension Drawing 29.6 29.6 Figure 3 Opal5 Dimensions for DIN-Rail Mounting (unit: mm) Kyland Opal5/Opal8 IM-EN-June 2016... -
Page 10: Mounting Modes And Steps
45.6 45.6 Figure 4 Opal8 Dimensions for DIN-Rail Mounting (unit: mm) Caution: As part of the heat dissipation system, the switch housing becomes ● hot during operation. Please use caution when coming in contact and avoid covering the switch housing when the switch is running. The figures in this manual are only for reference. -
Page 11: Din-Rail Dismounting
DIN rail connecting seat DIN rail Figure 5 DIN-Rail Mounting 3.2.2 DIN-Rail Dismounting Step 1: As shown in the following figure, press the device downward and move the device in direction 1 until the bottom of the device is detached from the DIN rail. Step 2: Pull the device upward and move the device in direction 2 until the device is removed from the DIN rail completely. -
Page 12: Pin Definition
Pin Definition ● Figure 7 RJ45 Port Table 3 Pin Definitions of 10/100Base-T(X) RJ45 Port Wiring Sequence ● Straight-through Cable RJ45 RJ45 Crossover Cable RJ45 RJ45 Figure 8 Connection Using Straight-through/Cross-over Cable Note: The color of the cable for RJ45 connector meets the 568B standard: 1- orange and white, 2-orange, 3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and 8-brown. -
Page 13: Base-Fx Ethernet Port
4.2 100Base-FX Ethernet Port 100Base-FX Ethernet port is equipped with ST/SC connector, and each port consists of TX (transmit) port and RX (receive) port. To enable data transmis- sion between Device A and Device B, connect the TX port of Device A to the RX port of Device B, and the RX port of Device A to the TX port of Device B. - Page 14 The center Wavelength (CWL) of SFP module above is 1310nm. 100Base-XSFP Optical Module ● Figure 10 100Base-XSFP Optical Module SFP optical module is equipped with LC connector, and each port consists of a TX (transmit) port and an RX (receive) port. To enable communication between Device A and Device B, connect the TX (transmit) port of Device A to the RX (receive) port of Device B, and the RX (receive) port of Device A to the TX (transmit) port of Device B.
-
Page 15: Power Terminal Block
How to Determine the RX Port and TX Port of SFP Optical Module 1. Insert the two connectors in one end of optical fiber into the SFP module, and those in the other end of the optical fiber into the SFP module of another switch. 2. - Page 16 Note: Others: Suitable cable with temperature of 85.5℃ at least must ● be used for the power input terminal. All field wiring intended for connection to the power terminal shall ● consist of copper conductors with the insulation locally removed. Additional intermediate connecting parts, other than ferrules, shall not be used.
-
Page 17: Dip Switches
Caution: Provision shall be made to prevent the rated voltage from being ● exceeded by transient disturbances of more than 140% of the rated voltage. Power adapter provide by end customershall be non-sparking. ● Before connecting the device to power supply, make sure that the ●... - Page 18 5 LEDs Table 8 LEDs Kyland Opal5/Opal8 IM-EN-June 2016...
-
Page 19: Basic Features And Specifications
6 Basic Features and Specifications Kyland Opal5/Opal8 IM-EN-June 2016... -
Page 20: Certificates Used For Compliance
7 Certificates Used for Compliance 8 Appendix 1. UL control number:4SH7,3MSY. 2. The product identity: IND. CONT. EQ. FOR HAZ. LOC. Class I, Division 2, Groups A, B, C and D Hazardous Locations. 3. Max Ambient temperature:75℃ for Opal5/8 series and 60℃ for Opal5/8-E series. - Page 21 6.Condition of safe use: The equipment shall only be used in an area of not more than pollution ● degree 2, as defined in EN/IEC 60664-1. The equipment shall be installed in an enclosure that provides a degree of ● protection not less than IP 54 in accordance with EN/IEC 60079-15 and enclosure only accessible with tool removable cover.
- Page 22 Kyland Technology Co., Ltd. FAX: +86-10-88796678 Website: http://www.kyland.com Email: support@kyland.com Factory Address: NO.901, FLOOR8-12, BUILDING NO.2, SHIXING AVENUE30#, SHIJINGSHAN DIST, BEIJING 100144 CHINA...
Need help?
Do you have a question about the Opal5 series and is the answer not in the manual?
Questions and answers