Related Manuals for Triax CGS 470
Summary of Contents for Triax CGS 470
- Page 1 Assembly Instruction CGS 470 Model Item no. CGS 470 325010 Version Date 01/2017...
- Page 2 o n t e n t s 1 Safety regulations ....................3 2 General information ..................3 2.1 Scope of delivery ................3 2.2 Meaning of the symbols used ............... 4 2.3 Technical data..................4 2.4 Description ..................5 3 Installation ......................7 3.1 Retrofitting a CA module ..............7 3.2 Setting the operating voltage of the CA module ........8 3.3 Installing the digital module ..............9 3.4 Connecting the digital module ............
- Page 3 a f e t y r e g u l a t i o n s • The standards IEC/EN/DIN EN 50083 resp. IEC/EN/DIN EN 60728 must be observed. • Do not perform installation and service work during thunderstorms. • Assembly, installation and servicing should be carried out by authorised electricians. • Switch off the operating voltage of the system before beginning with assem- bly or service work. • Avoid short circuits! • Observe the relevant standards, regulations and guidelines on the installa- tion and operation of antenna systems.
- Page 4 2.2 m e a n i n g t h e s ym b o l s u s e d Important note —> General note – – Optional use of the buttons • Performing works 2.3 t e C h n i C a l data The requirements of the following are met: 2011/65/EU, 2014/30/EU, 2014/35/EU The product fulfils the guidelines and standards for CE labelling.
-
Page 5: Description
2.4 d es C r i p t i o n The module CGS 470, in the following called digital module, has a QPSK AV converter which simultaneously converts four QPSK modulated channels into AV signals using two SAT tuners. It is additionally equipped with a common inter- face, which enables the descrambling of up to 4 scrambled channels through a single data stream when used in conjunction with a CA module and an appropri- ate smart card from a service provider. The digital module has two SAT inputs and one AV interface, through which the decoded AV signals are fed to the corresponding modulator module. Compo- nents (e.g. LNB) which are connected upstream can be powered through the SAT inputs. The channel strips "A" "B", "C" and "D" can be individually programmed. This means it is possible to select up to 4 channels from two transponders. Via tuner "A" scrambled and unscrambled channels can be received. Tuner "D" is prepared to receive unscrambled channels only. The following tables show the possible allocations of the selectable number of channels to the tuners. For example, if three unscrambled channels from tuner "A" will be used, one unscrambled channel from tuner "D" can be used. If , e.g. two unscrambled channels from tuner "A" will be used, two unscrambled channels from tuner "D" can be used. Tuner "A" Tuner "D" Quantity of unen- crypted channels For example, if four scrambled channels from tuner "A" will be used, no chan- nel from tuner "D" can be used. If , e.g. two scrambled channels from tuner "A" will be used, two unscrambled channels from tuner "D" can be used. Tuner "A" Tuner "D" (encrypted (unencrypted channels) - Page 6 The digital module operating software can be updated using a PC or note- book and the software "BE-Flash" via the 9-pin D-SUB socket on the head-end station. You can find the current operating software for the digital module, the software "BE-Flash" and the current assembly instructions on the website "www.triax.com". This digital module is designed exclusively for use in the CSE 2800 head-end station. - 6 -...
-
Page 7: Installation
n s t a l l a t i o n – Ensure the head-end station is mounted so it will not be able to vibrate. Avoid, for example, mounting the head-end station onto a lift shaft or any other wall or floor construction that vibrates in a similar way. – Before installing or changing a module, switch off the head-end station or unplug the power cable from the mains power socket. Take measures to protect against ESD! • Open the housing of the head-end station in accordance with the assembly instructions for the CSE 2800. 3.1 r Ca e t r o f i t t i n g m o d u l e The digital module is equipped with a common interface. It allows you to connect a CA module for various scrambling systems and service providers. - Page 8 3.2 s Ca e t t i n g t h e o p e r at i n g vo ltag e t h e m o d u l e The CA modules can require different operating voltages. • Set the required operating voltage by plugging the jumper to the respective contacts: Contacts Operating voltage 1 - 2 + 5 V (Factory default) 3 - 4 + 3.3 V - 8 -...
-
Page 9: Installing The Digital Module
3.3 i n s ta l l i n g t h e d i g i ta l m o d u l e – If a CA module is used, check that the plug contacts of the CA module are tightly seated in the terminal strip on the digital module and make sure there is a reliable contact. – Always position modules which belong together next to each other. The digital module must be installed to the left of the modulator module. - Page 10 • Install the appropriate modulator module. —> Figure 5 shows the slots 1 (digital module) and 2 (modulator mod- ule). The slot between them (without a contact strip on the board at the rear wall of the housing) is for an add-on module only. • After installing the modules close the locking device in direction of the arrow. 3.4 C o n n e C t i n g t h e d i g i ta l m o d u l e • Connect SAT-IF inputs of the digital module to the preinstalled F termi- nals in the rear wall of the head-end station via the cable inlets using HF cables made on-site (length approx. 80 cm) or if applicable to one of the outputs of a retrofitted SAT-IF input distributor.
-
Page 11: Menu Items
C o n t r o l p a n e l g l a n C e 4.1 m e n u i t e m s Program the module using the buttons on the head-end station control unit. The menus appear on the two-line display of the control unit. The parameters and functions to be set are underlined. You can use the button to select the following menu items: – LNB oscillator frequency – Tuner selection (channel strips "B", "C" and "D" only) – Symbol rate – Input frequency – Station filter – Audio stream selection – Audio output level... -
Page 12: Programming
r o g r a m m i n g 5.1 p r e pa r at i o n • Connect the digital module to a programmed modulator module. —> For the programming of the output channels please read the assem- bly instructions of the corresponding modulator module. • Connect the test receiver to the HF output on the modulator module. • Adjust the test receiver to the output channel of the channel strip to be set: Digital module – channel strip "A" —> modulator module – channel strip "A", Digital module – channel strip "B" —> modulator module – channel strip "B", Digital module – channel strip "C" —> modulator module – channel strip "C", Digital module – channel strip "D" —> modulator module – channel strip "D". • Switch on the modulator if necessary. For each modulator, there is a green LED which indicates if the modulator is switched on. LED – Channel strip “A“ LED –... - Page 13 5.2 p r o g r a m m i n g p r o C e d u r e Bedienhinweise Operating Hints Ein/On "blättert" Menüs vorwärts. scrolls forward through the menu. wählen die Eingabeposition select the enter position. BE160 SETUP wählt Untermenü...
- Page 14 mpeg DUAL norm mpeg / VPS Bx 1… VIDEO Letter Letter / 16:9 Bx 1… VIDEO WSS on TXT on on / off Bx 1… TESTLINES on / off Bx 1… SUBTITLE Bx 1… SUBTITLE Bx 1… SUBTITLE Bx 1… SUBTITLE west –...
-
Page 15: Selecting The Module / Channel Strip
5.3 p r o g r a m m i n g t h e d i g i ta l m o d u l e Notes: – Entries are saved by pressing the button. —> You will be returned to "Selecting the module/channel strip". – The programming process can be cancelled by pressing and holding the button. —> You will be returned to "Selecting the module/channel strip". • Switch on the head-end station. —> The display shows "SETUP BE160" and the software version of the head-end station (e.g. V 10). -
Page 16: Tuner
e l e C t i n g t h e m o d u l e C h a n n e l s t r i p • Press repeatedly if necessary to select the particular module (Bx ...) or channel strip "A", "B", "C" or "D" to be programmed. Bx 1A TWIN-SAT Böx 4 TWIN-SAT Bx 1A QUAD Bx 1B QUAD... -
Page 17: Lnb Oscillator Frequency
• Using buttons select the tuner: For Channel strips "B" and "C": "TUNER Line A" or "TUNER Line D", For Channel strip "D": "TUNER Line D" or "TUNER Line A CA" • Press the button. Channel strip A / Channel D with setting "Tuner Line D": —> The "LNB oscillator frequency" – "LNB" menu is activated. Channel strip B or C / Channel strip D with setting "Tuner Line A CA": —> The "Station filter" menu is activated (page 20). lnb os C i l l ato r f r e q u e n C y —> This menu is only displayed in channel strip A / channel strip D with setting "Tuner Line D". Bx 1A Bx 1A MENU 10600 MHz >... -
Page 18: Input Symbol Rate
m o d u l e a r d i n f o r m at i o n A menu has been provided for these settings, which is displayed on your TV screen. The menu varies according to which CA module is used. For this rea- son, please refer to the operating manual of your particular CA module. The relevant information is shown on the display of the head-end station. • Use to select a menu item on the screen. • Activate the menu item with • Select the required function with the buttons. • Press the button to store the settings. • Press the button. —> Input symbol rate" – "SYMBOL" menu is activated. n p u t s ym b o l r at e —> This menu is only displayed in selection channel strip A and selec-... -
Page 19: Input Frequency
n p u t f r e q u e n C y —> This menu is only displayed in selection channel strip A and selec- tion channel strip D with setting "Tuner Line D". —> Once the HF receiver has synchronised to the input signal, any offset to the target frequency is displayed in MHz, e.g. "+ 0.2". —> If a question mark "?" appears in the second line of the display, there is no input signal present. Check the configuration of the an- tenna system and head-end station as well as the preceding settings of the module in question. -
Page 20: Station Filter
—> The "Station filter" menu is activated. tat i o n f i lt e r In this menu, select the channel from the data stream that is to be made avail- able through this channel strip. If the error message "SERVICE no transponder" appears, no input signal is present. In this case, you should check the previous settings as well as the configuration of the SAT antenna system. If the "scanning ..." message appears on the display, the table of received channels is being read. Please wait until this process is finished. As soon as the station filter has found all of the TV or radio channels, the corre- sponding data appears in the display of the head-end station. -
Page 21: Audio Stream For A Tv Channel
• Select the desired TV or radio channel with the buttons. • Press the button. —> If the selected channel is broadcast with two or more audio streams, the "Audio stream for a TV channel" – "AUDIO" menu will appear. Otherwise the "Volume level" – "AUDIO Level" menu is activated (see page 21). t v u d i o s t r e a m f o r C h a n n e l This menu only appears if the selected channel is broadcast with two or more audio streams (languages). In this menu, select the desired audio stream from the transport stream. -
Page 22: Selecting The Picture Format
d e n t i f i C at i o n t h e s t e r e o d ua l to n e In this menu, you can select whether the stereo audio identification is decoded from the VPS data or from the MPEG data stream. Further you can swap the languages on TV stations with dual tone. Bx 1A AUDIO mpeg DUAL norm • Using the buttons, select the data stream from which the identification ("mpeg" or "VPS") to be used. • Use the buttons to position the cursor under the dual tone code "DUAL …" to be set. -
Page 23: Activating Test Lines
11836 MHz +0.2 i C t u r e f o r m at s i g n a l e l e t e x t m o d e Bx 1A 01/07 + TV If problems with the automatic picture format switchover (e.g. 4:3, 16:9, Letter- Das Erste Programmauswahl / Channel selection box) arise with the connected devices, you can switch "off" the Wide-Screen- Signaling (WSS) in this menu. -
Page 24: Black Bar
e l e t e x t s u bt i t l e pag es a n d ta n da r d This menu allows subtitles (transmitted in teletext or DVB data stream) to be displayed directly in the channel or parts of the screen to be masked by a black bar. Using the buttons, the submenus can be selected. With set- ting "SUBTITLE - off" subtitle function is switched off. -
Page 25: Storing Data
l selection dvb C t i vat i n g s u bt i t l e pag es on / off This menu allows subtitles transmitted in a DVB data stream to be displayed bei Auswahlmöglichkeit directly in the channel. The language of the subtitles can be selected. ne angezeigt. displayed if several audio able. • Using the buttons select the submenu "SUBTITLE - dvb". Bx 1A SUBTITLE Bx 1A SUBTITLE Bx 1A SUBTITLE... - Page 26 to r i n g data Bx 1A MEMORY S => STORE CANCEL • All programmed data is saved by pressing the button. Then you will be returned to the menu item "Selecting the module / channel strip" (page 16). —> By pressing the button, you will be returned to the menu item "Se- lecting the module / channel strip" without saving the programmed data. - 26 - CGS 470...
- Page 27 i n a l pro C e d u res After installing the head-end station, upgrading accessories or installing mod- ules it is necessary to tighten all cable connections, cable terminals and cover screws in order to maintain compliance with current EMC regulations. • Securely tighten the cable connections (F connectors) using an open-ended spanner (spanner gap 11 mm). • Test the output level of the output collector according to the CSE 2800 as- sembly instructions and set the output level required for the cable system. • Mount the base plate and the front cover (see CSE 2800 assembly instruc- tions). - 27 - CGS 470...
- Page 28 For further information and updated manuals go to Copyright © 2016 TRIAX. All rights reserved. The TRIAX Logo and TRIAX, TRIAX Multimedia are registered trademarks or trademarks of the TRIAX Company or its affiliates. All specifications in this guide are subject to change without further notice.