Kernel/Drv/Fjpfca.conf" Example - Fujitsu l ETERNUS AF Configuration Manual

Chapter 6 Required Driver Parameters
6.1 Setting Up the Parameters
6.1.2

"/kernel/drv/fjpfca.conf" Example

• Description example for ETERNUS DX400/DX400 S2 series
#
# All Rights Reserved, Copyright (c) FUJITSU LIMITED 2000
#
#ident "@(#)$Id: fjpfca.conf,v 1.3 2000/05/30 13:59:43 ueno Exp $ FUJITSU"
# The fjpfca driver support connection to NL_port(FC-AL) and
# F_Port/FL_Port(fabric).
# It is necessary to define "port" property in order to communicate
# with the fabric or N_port target. In addition, it is necessary
# to define "fcp-bind-target" property in order to communicate
# with the fabric. These need not be defined for FC-AL.
# Other properties like "alias" and "max-throttle" are optional.
# Alias name definition
# You can create an alias definition for a specific WWN
# with "alias" property.
# SYNOPSIS:
# alias="alias-name:wwn", ...;
# EXAMPLE:
# alias="TARGET_A:0x100000a0b8030001","TARGET_B:0x100000a0b8030002";
#
#alias=
# "TARGET_0A:0x100000a0b8030001",
# "TARGET_1A:0x100000a0b8030002",
# "TARGET_0B:0x100000a0b8030003",
# "TARGET_1B:0x100000a0b8030004";
alias= "DX400_CM0CA0P0:0x202000e000cb0001",
"DX400_CM1CA0P0:0x203000e000cb0001";
# Port type definition
# The port type definition sets the port mode for a specific instance.
# If the "port" property is not defined, the fjpfca driver
# will determine the port mode automatically during the initialization.
# SYNOPSIS:
# port="instance-name:[nport|loop]", ...;
# EXAMPLE:
# port="fjpfca0:nport","fjpfca1:loop";
#
#port=
# "fjpfca0:nport",
# "fjpfca1:nport",
# "fjpfca2:nport",
# "fjpfca3:nport";
port= "fjpfca0:nport:sp4",
"fjpfca1:nport:sp4";
# Target binding definition
# fcp-bind-target binds a specific instance to a target ID.
# You can use defined alias in "alias" property for the WWN.
# SYNOPSIS:
# fcp-bind-target="[target-name:[wwn|alias-name]]", ...;
# EXAMPLE:
# fcp-bind-target= "fjpfca0t0:0x100000a0b8030001","fjpfca1t0:TARGET_B";
#
#
#fcp-bind-target=
# "fjpfca0t0:0x100000a0b8030001",
# "fjpfca0t1:0x100000a0b8030003",
# "fjpfca1t0:TARGET_1A",
# "fjpfca1t1:TARGET_1B";
fcp-bind-target= "fjpfca0t0:DX400_CM0CA0P0",
# Number of maximum commands per target definition
# The driver uses the value specified by the max-throttle property
# as a number a target of commands which can be issued simultaneously.
# SYNOPSIS:
# max-throttle="[target-name:number]", ...;
# EXAMPLE:
# max-throttle="fjpfca0t0:240","fjpfca1t0:240";
#
#max-throttle=
# "fjpfca0t0:240",
# "fjpfca0t1:128",
# "fjpfca1t0:240",
# "fjpfca1t1:128";
max-throttle= "fjpfca0t0:255",
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
For direct connections, set this parameter if required.
For direct connections, this setting is not required.
For direct connections, this setting is not required.
"fjpfca1t0:DX400_CM1CA0P0";
For both direct connections and switch connections, add this setting.
"fjpfca1t0:255";
Copyright 2017 FUJITSU LIMITED
24
P3AM-3712-15ENZ0