Table of Contents
Advertisement
Safe Operation
The following safety information is vitally important
for safe operation of the MHP15J. Failure to follow
these instructions can result in personal injury or
DEATH.
Pre-start Inspection
At the start of each work shift, the MHP15J shall be
given a visual inspection and function test. See the
"Pre-operational Inspection" chapter 7, in this man-
ual for a list of items to inspect and test.
CAUTION
DO NOT operate the MHP15J unless you are
trained and authorized, understand the
operation characteristics of the MHP15J,
and have inspected and tested all functions
to be sure they are in proper working order.
Work Place Inspection and Practices
Do not use the MHP15J as a ground for welding.
Ground to the work piece.
Before the MHP15J is used, and during use, check
the area in which the MHP15J is to be used for pos-
sible hazards such as, but not limited to:
1. Drop-offs or holes.
2. Side slopes.
3. Bumps and floor obstructions.
4. Debris.
5. Overhead obstructions and electrical
conductors.
6. Hazardous locations.
7. Inadequate surface and support to withstand
all load forces imposed by the aerial platform
in all operating configurations.
8. Wind and weather conditions.
9. Presence of unauthorized persons.
10. Other possible unsafe conditions.
Before the MHP15J is used, determine the hazard
classification of any particular atmosphere or loca-
tion according to ANSI/NFPA 505-1987.
Any MHP15J operated in a hazardous location
must be approved and of the type required by
ANSI/NFPA 505-1987.
A recommended safety practice is to have
personnel that are trained in the operation of the
emergency controls working in the immediate area
of the MHP15J to assist the platform operator in the
event of an emergency.
MHP15J – 11995A
Chapter 1. Safety
When moving the platform, check the clearance
around the MHP15J to avoid contact with struc-
tures or other hazards. Always look in the direction
of motion.
Keep ground personnel from under the platform
when the platform is raised.
Secure all accessories, containers, tools, and other
materials in the platform to prevent them from acci-
dentally falling or being kicked off the platform.
DO NOT engage in any form of "horseplay" or
"stunt driving" while operating the MHP15J.
DO NOT permit riders on the machine anyplace
other than on the platform.
Remove all loose objects stored in or on the ma-
chine, particularly in the platform. Remove all ob-
jects which do not belong in or on the machine.
When other moving equipment is in the area, take
special precautions to comply with local regula-
tions regarding warnings.
Never steady the platform by positioning it against
another platform.
DO NOT operate an MHP15J that is not functioning
properly, or has been damaged, until the machine
has been repaired by a qualified maintenance per-
son.
DO NOT operate a MHP15J that does not have all
its decals and placards attached and legible.
Watch for bystanders and never allow anyone to be
under, or to reach through, the machine and its
equipment while operating.
Use the recommended transport device when
loading the machine.
Electrocution
T h e
M H P 1 5 J
i s
a n
NON-INSULATED, aerial work platform.
DO NOT operate it near ELECTRICAL conductors.
Regard all conductors as being energized.
DO NOT operate outside during a thunderstorm.
Tipover and Falling Hazards
DO NOT operate the MHP15J from a position on
trucks, trailers, railway cars, floating vessels, scaf-
folds, or similar equipment unless the application is
approved in writing by Snorkel.
If the platform or elevating assembly becomes
caught, snagged, or otherwise prevented from
normal motion by an adjacent structure or other
obstacles such that control reversal does not free
the platform, remove all personnel from the
a l l
m e t a l
b o o m ,
page 1 - 1
Advertisement
Table of Contents
