Labels & Cosmetics - Shop fox W1851 Owner's Manual

707
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
706
705
WARNING
ACCIDENTAL INJURY
HAZARD!
Disconnect power
supply before
adjustments, setup
or maintenance!
704
The Model W1851
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:
BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width: 13/16"
702
701
2 HP 10" HYBRID TABLE SAW w/EXTENSION TABLE
Specifications
Motor: 2 HP, 115V/230V, 60 Hz, Single-Phase To reduce risk of serious injury when using this machine:
Pre-Wired: 230V
1. Read and understand owner's manual before operating.
Full-Load Current Rating: 16A at 115V, 8A at 230V
2. Never touch moving blade, and keep hands out of cutting path.
Blade Size: 10" x 5/8" Arbor
3. Always wear approved eye protection and respirator.
Required Blade Kerf Thickness: 0.102"–0.126"
4. Only plug power cord into a grounded outlet.
Arbor Speed: 3850 RPM
Max. Rip Capacity: 31-1/2" 5. Always use blade guard/spreader for all through cuts; and use
Max. Depth of Cut @ 90˚: 3-1/8" riving knife for all non-through cuts. If a certain cut cannot be
Max. Depth of Cut @ 45˚: 2-3/16" made with either device, some other safeguard MUST be used.
Max. Dado Width: 13/16"
6. Only use blades meeting size/speed requirements for this saw.
Weight: 396 lbs.
7. Ensure spreader/riving knife and fence are properly adjusted.
8. Never reach behind or over blade while it is moving.
S/N
9. Use a push stick when required and whenever possible,
especially with small/narrow workpieces and non-through cuts.
Date
10. Know what causes "kickback" and how to prevent it.
Mfd. for Woodstock in China 11. Never remove jammed/cutoff workpiece when blade is moving!
REF PART # DESCRIPTION
701 X1851701 MACHINE ID LABEL
702 X1851702 READ MANUAL LABEL
703 X1851703 TABLE SAW WARNING LABEL
704 X1851704 RIVING KNIFE CAUTION LABEL
705 X1851705 DISCONNECT POWER LABEL
706 X1851706 ELECTRICITY LABEL
707 X1851707 DON'T OPEN DOOR WARNING LABEL
Safety.labels.warn.about.machine.hazards.and.how.to.prevent.serious.personal.injury..The.owner.
of.this.machine.MUST.maintain.the.original.location.and.readability.of.all.labels.on.this.machine..
If.any.label.is.removed.or.becomes.unreadable,.REPLACE.that.label.before.allowing.machine.to.
be.operated.again..Contact.us.at.(360).734-3482.or.www.woodstockint.com.to.order.new.labels..
Labels.&.Cosmetics
708
AMPUTATION
Removing blade If blade guard is
HAZARD!
guard increases removed for a
Always keep
fingers and risk of injury—it special cut, some
hands away from MUST be installed other safeguard
moving blade. when possible. MUST be used.
703
WARNING!
READ and UNDERSTAND
MANUAL to avoid serious
injury! If a manual is not
available, DO NOT use
machine! Instead, go to
www.woodstockint.com
or call (360) 734-3482.
MODEL W1851
WARNING!
12. Make sure blade is stopped before adjusting the height or tilt.
13. Do not perform any operation freehand.
14. Never use fence and miter gauge at the same time.
15. Ensure machine is stable and fence is parallel with blade.
16. Disconnect power before changing blades or servicing saw.
17. Plan cuts so that workpieces always remain supported.
18. Non-through cuts (i.e. dadoes, rabbets, moulding cuts) and
resawing cuts present specific dangers; refer to the manual.
19. Do not wear loose clothing, gloves, jewelry, or other items that
can get entangled. Tie back long hair and roll up sleeves.
20. Do not expose to rain or operate in a wet environment.
21. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
Model W1851 (For Machines Mfd. Since 10/17)
Disconnect power
before changing
blades or blade
guard and riving
knife.
710
713
***
REF PART # DESCRIPTION
708 X1851708 BLADE GUARD LABEL
709 X1851709 HANDWHEELS NOTICE LABEL
710 X1851710 TOUCH-UP PAINT, SHOP FOX WHITE
711 X1851711 EYE/LUNG HAZARD LABEL
712 X1851712 SHOP FOX NAMEPLATE D3377
713 X1851713 MODEL NUMBER LABEL
-94-
709
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
711
WARNING!
EYE/EAR/LUNG
INJURY HAZARD!
Always wear safety
glasses, ear protection,
and respirator when
using this machine.
712
Use D3377
(5 ⁄ " X 11 ⁄ ")
1 1
8 8