Tektronix WVR720UP Instructions Manual
  1. Manuals
  2. Brands
  3. Tektronix Manuals
  4. Measuring Instruments
  5. WVR720UP
  6. Instructions manual
Tektronix WVR720UP Instructions Manual

Tektronix WVR720UP Instructions Manual

Waveform rasterizers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WVR720UP, WVR820UP, and WVR830UP Upgrades
xx
for the WVR7200, WVR8200, and WVR8300
Waveform Rasterizers
ZZZ
Instructions
Warning
The servicing instructions are for use by qualified personnel
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do so. Refer to all safety summaries
prior to performing service.
www.tektronix.com
*P075101603*
075-1016-03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WVR720UP and is the answer not in the manual?

Questions and answers

Related Manuals for Tektronix WVR720UP

Summary of Contents for Tektronix WVR720UP

  • Page 1 WVR720UP, WVR820UP, and WVR830UP Upgrades for the WVR7200, WVR8200, and WVR8300 Waveform Rasterizers Instructions Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service.
  • Page 2 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material.

  • Page 3: Table Of Contents

    Upgrade installation ....................Verify the currently installed options ............... How to prevent electrostatic discharge ..............Install software upgrade..................Install the option hardware................... Install the option software key ................Verify the upgrade ....................Quick verification..................... Detailed verification ..................WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 4 Table of Contents WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 5: Important Safety Information

    Read the safety sections of the other component manuals for warnings and cautions related to operating the system. When incorporating this equipment into a system, the safety of that system is the responsibility of the assembler of the system. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 6 Do not operate in wet/damp conditions. Be aware that condensation may occur if a unit is moved from a cold to a warm environment. Do not operate in an explosive atmosphere. Keep product surfaces clean and dry. Remove the input signals before you clean the product. WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 7: Service Safety Summary

    Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics professional to avoid stress injuries. Use care when lifting and carrying the product. Use only the Tektronix rackmount hardware specified for this product. Service safety summary The Service safety summary section contains additional information required to safely perform service on the product.

  • Page 8: Terms In This Manual

    find out the nature of the potential hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to ratings in the manual.) The following symbol(s) may appear on the product: WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 9: Kit Description

    Kit description Kit description This document provides instructions for installing the video, audio, and analysis upgrades listed in the following tables into an existing Tektronix WVR7200, WVR8200, or WVR8300 waveform rasterizer. Table 1: Supported video upgrades Video upgrades WVR820UP WVR830UP...
  • Page 10 Option PROD Adds Advanced Gamut Monitoring Package (Spearhead Display and Luma Qualified Vector Display). Option DAT Adds data analysis capabilities. Allows for logic-level view of video and embedded audio data stream and ANC data extraction. WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 11: Products

    Kit description Products The following Tektronix products are supported by this kit: WVR7200 (all instruments) WVR8200 (all instruments) WVR8300 (all instruments) Required tools The following table lists the tools required to install the upgrade. Table 4: Required tools Name Description...

  • Page 12: Kit Parts Lists

    1 EA 335-2393-XX LABEL REAR PANEL, SDI NOTE. Once the hardware is installed, you must download the software to activate Option 2SDI. Go to www.tektronix.com/downloads. (See page 14, Install software upgrade.) WVR820UP CPS Table 6: Option CPS parts list WVR830UP CPS...
  • Page 13 220-0497-XX NUT, PLAIN, HEX; .5-28 X .562 HEX, BRS, NI (NICKEL) PLATED 4 EA 210-1039-XX WASHER, LOCK; 0.521 ID, INT, 0.025 THK, STEEL, ZINC FINISH 1 EA 335-2394-XX LABEL REAR PANEL, EYE, SDI CLOCK OUT WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 14 SCREW, JACK; 4-40 X 0.312 LONG, 0.188 H HEX HEAD STAND OFF, 4-40 INT THD, X 0.312 THD EXT 4-40, STEEL, ZINC PLATED 1 EA 131-7430-XX CONN,DSUB; SLDR CUP,MALE,STR,62 POS,0.100 CTR,30 GOLD 1 EA 200-4804-XX COVER; SHIELD,ELEC CONN,37 POS DSUB,ZINC WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 15 SCREW, JACK; 4-40 X 0.312 LONG, 0.188 H HEX HEAD STAND OFF, 4-40 INT THD, X 0.312 THD EXT 4-40, STEEL, ZINC PLATED 1 EA 131-7430-XX CONN,DSUB; SLDR CUP,MALE,STR,62 POS,0.100 CTR,30 GOLD 1 EA 200-4804-XX COVER; SHIELD,ELEC CONN,37 POS DSUB,ZINC WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 16: Upgrade Installation

    1. Power on the instrument you are upgrading. 2. Press the CONFIG button on the front panel. 3. Navigate to Utilities > View Instrument Options. 4. Make a list of the installed options. List installed options WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 17: How To Prevent Electrostatic Discharge

    5. Do not allow anything capable of generating or holding a static charge on the work surface. 6. Handle circuit boards by the edges or hold onto grounded shields when possible. 7. Do not slide circuit boards over any surface. WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 18: Install Software Upgrade

    Instrument Software version number 3. Verify the latest version of software at the Tektronix Web site: a. Use the Web browser on a PC to navigate to the following Tektronix Web site: http://www.tektronix.com/downloads b. On the Downloads Finder Web page, search by model number (such as WVR8300) and filter by software and software type to locate the...
  • Page 19 Once the instrument has started to erase internal flash, DO NOT remove power from the instrument. If you do so, the instrument flash will be corrupted. The instrument will have to be sent to a Tektronix factory service center to have the system software restored.
  • Page 20 Navigate to Network Settings > IP Config Mode. c. Select either Manual or DHCP as directed by your LAN administrator. Select Manual if you are using an Ethernet cable to connect the PC directly to the instrument. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 21 Enter. This starts the software upgrade process. CAUTION. To prevent upgrade failure, do not close the transfer.exe window until the transfer utility asks for another IP address. When the software upgrade completes, the instrument may reboot. WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 22: Install The Option Hardware

    For software-only upgrades, you do not need to remove the instrument cover since these upgrades are enabled by the new software key you received with this kit. (See page 35, Install the option software key.) WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 23 1. Arrange access to the top of the instrument (remove from rack as needed). 2. Remove the 18 T-10 screws that secure the cabinet top cover to its chassis and lift the cover off. Save the screws for reinstallation. Figure 2: Top cover removal WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 24 SDI video board, there are three screws to remove. (See Figure 9 on page 27.) If removing an existing EYE or PHY/PHY3 option video board, there are six screws to remove. (See Figure 4.) Figure 3: SDI board WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 25 Upgrade installation Figure 4: Option EYE or PHY/PHY3 board WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 26 5. Grasp the video card near the location of the connector that is located beneath the video board. Gently lift the existing video board up at a slight angle to disengage the connector underneath the video board. and out of the instrument. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 27 Pressing only over the location of the connector, gently press the video board down until the connectors engage. (See Figure 8 on page 26.) The video board should sit firmly on all six posts. Figure 6: Video board connector location WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 28 Otherwise, proceed to installing the next module. a. Secure the cabinet top cover to its chassis with the 18 T-10 screws previously removed. b. Install the option software key. (See page 35, Install the option software key.) WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 29 Figure 7: Option CPS board 3. Remove the four nuts and lock washers securing the BNC connectors CMPST A LOOP-THROUGH and CMPST B LOOP-THROUGH. CAUTION. Do not flex or bend the circuit boards when removing. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 30 Pressing only over the location of the connector, gently press the SDI board down until the connectors engage. (See Figure 8.) The SDI board should sit firmly on all six posts. Figure 8: SDI board connector location WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 31 Install the option software key. (See page 35, Install the option software key.) NOTE. Once the hardware is installed, you must download the software to activate Option 2SDI. Go to www.tektronix.com/downloads. (See page 14, Install software upgrade.) WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 32 4. Line up the BNC connectors on the CPS board to the holes in the rear panel and slide the board into the mainframe until BNC connectors fully protrude through the rear panel. CAUTION. Do not flex or bend the circuit board when installing. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 33 Tighten firmly, but not excessively. (See Figure 7 on page 25.) 7. Secure the four BNC connectors using the four lock washers and BNC nuts from the kit. 8. Attach the new CMPST label below the BNC connectors. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 34 2. Remove the eight plugs from the AES holes on the rear of the instrument. 3. Remove the two screws that secure the blank cover from the Analog Audio I/O hole.(See Figure 12.) Figure 12: Remove blank cover for audio connector WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 35 5. Line up the BNC connectors to the holes in the rear panel and slide the audio board into the mainframe until BNC connectors fully protrude through the rear panel. 6. The audio board should sit firmly on all three posts. WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 36 9. Use a 3/16 in. nut driver to install the two retainer posts from this kit to secure audio connector to the rear panel. (See Figure 15.) Figure 15: Audio connector retainer posts WVR720UP, WVR820UP, and WVR830UP Upgrades...
  • Page 37 An example of a suitable cable is Belden 8451, which is a shielded twisted pair cable. Alternatively, you can purchase an audio breakout cable (Tektronix part number 012-1688-00), which provides a two meter cable with XLR connectors for all twelve inputs and eight outputs.
  • Page 38 4. Remove the three T-15 screws securing the audio board. (See Figure 18.) 5. Lift the audio board out of the instrument and store it in a static safe location. 6. Return to your original installation procedure. Figure 18: Audio board installed WVR720UP, WVR820UP, and WVR830UP Upgrades...

  • Page 39: Install The Option Software Key

    On the PC, open your Web browser application. b. In the address bar of the Web browser, enter the IP address of the instrument you are upgrading. This opens the Tektronix WVR8200/WVR8300 Remote Interface screen. c. Click the Instrument Options link to open the Active WVR8200/8300 Options screen.

  • Page 40: Verify The Upgrade

    NOTE. If the option(s) you just installed are not listed or if your previously installed options are not listed, contact Tektronix for assistance. 3. Verify that the instrument passes the advanced diagnostic tests by performing the following steps: a.

This manual is also suitable for:

Wvr820upWvr7200Wvr830upWvr8200Wvr8300

Table of Contents