Lanner FW-8877 User Manual page 20

Chapter 3
VGA1: VGA Interface. with a 2x6 (2.54") pin header.
It is for connecting the VGA interface cable.
IPMI card (connector Reference NO. OPMA1) has to be
present for this connector to work, i.e., the IPMI card
provides VGA interface/signal.
2
1
Pin No. Function
1 R
3 G
5 B
7 H-SYNC
9 V-SYNC
11 Detect-display
Data
Note: A 2x6 pin (2.0") header (J1) on the OPMA card
is also provided as an VGA interface connector.
CF1: CF Card Connector
Pin No. Description
1 GND
2 DATA3
3 DATA4
4 DATA5
5 DATA6
6 DATA7
7 CE1#
8 A10
9 OE#
10 A9
11 A8
12 A7
13 CFVCC3
14 A6
15 A5
16 A4
17 A3
18 A2
19 A1
20 A0
21 DATA0
22 DATA1
23 DATA2
24 WP
25 CD2-
ATX5: 24-Pin ATX Power Connector
23
1
Network Application Platforms
Note the
12
11
Pin No Function
2 Ground
4 Ground
6 Ground
8 Ground
10 Ground
12 Deteck-display
CLOCK
Pin No. Description
26 CD1-
27 DATA11
28 DATA12
29 DATA13
30 DATA14
31 DATA15
32 CE2#
33 VS1#
34 IOR#
35 IOW#
36 WE#
37 READY#
38 CFVCC3
39 CSEL
40 VS2#
41 RESET
42 WAIT#
43 INPACK#
44 REG#
45 DASP#
46 DIAG#
47 DATA8
48 DATA9
49 DATA10
50 GND
24
2
Motherboard Information
Pin No. Function
1 +3.3V
3 +3.3V
5 Ground
7 +5V
9 Ground
11 +5V
13 Ground
15 Power Good
17 Stand-By 5V
19 +12V
21 +12V
23 3.3V
ATX1, ATX3: 8-Pin ATX Power Connector
1
2
Pin No. Function Pin No.
1 GND
3 GND
5 GND
7 GND
COMA1: COM PORT Connector
Pin No. Description
10 9
1 DCD1
8 7
3 RXD1
6 5
5 TXD1
4 3
2 1 7 DTR1
GND
COMB1: COM PORT
10 9
Pin No. Description
1 DCD2-
8 7
6 5
3 RXD2
4 3
5 TXD2
2 1
7 DTR2-
9 GND
DIMM Sockets:
Since the system is capable of Quad Channel
configuration, some installation guidelines have to be
followed to enable Quad Channel mode. To insert 4 DIMMs
on the system, insert DIMMS into the 4 slots with black
latches. And then use slots with white latches if more slots
are required.
Note:
To activate Dual Channel instead of Quad
1.
Channel in the system, populate any 2 slots
with black latches. And then use slot with
white latch that belongs to the same channel
as the populated slot with black latch for any
additional DIMMs.
Starting from the board edge, one pair of black
2.
Pin No. Function
2 +3.3V
4 -12V
6 Ground
8 PSON-
10 Ground
12 Ground
14 Ground
16 NC
18 +5V
20 +5V
22 +5V
24 GND
7
8
Function
2 12V
4 12V
6 12V
8 12V
Pin No. Description
2 DSR1
4 RTS1
6 CTS1
8 RI1
10 FP_RESET_N
Pin No. Description
2 DSR2-
4 RTS2-
6 CTS2-
8 RI2-
10
14