Sony STR-DA5500ES Service Manual Digest page 18

STR-DA5500ES
Ver. 1.1
QQ
3 7 63 1515 0
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
DIRECT], [MUSIC], [MOVIE (HD-D.C.S.)] button in order, the message "MENU SPECIALIZED !" appears.
2. Press the [ ]/[ ] buttons of the remote commander, the message "<<< SPECIAL >>>" appears.
M m
3. Press the [ ] button of the remote commander, the item is appears.
,
4. Each time the [ ]/[ ] buttons of the remote commander is pressed, the item is switched in order as follows.
M m
Some items can change the content. Display the cursor by pressing the [
by pressing the [ ]/[ ] buttons of the remote commander, and fi x the content by pressing the [
M m
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE (HD-
D.C.S.)] button in order again, the message "MENU SPECIALIZE OFF" appears.
Items
SYSTEM version display
MAIN Ucom version display
Video Ucom version display
FAROUDJA version display
GUI CG-ROM version display
DSP Ucom version display
DSP serial fl ash version display
DSP parallel fl ash version display
IR learning Ucom version display
Network processor version
DSP debug menu
Network debug menu
TE
L 13942296513
MAC address display
(Network debug menu)
Network update check
Zone 4 display
FAROUDJA update
HDCP key read
Learning Ucom check
Model/destination change
Video factory menu
www
.
18
http://www.xiaoyu163.com
Display
SYSTEM VERSION X.XXX
MAIN ##### ∗∗∗ vX. XX
Video Ucom Ver X. XX
FAROUDJA Ver X. XX
GUI CGROM Ver X. XX
DSP Ucom Ver X. XX
DSP SFLASH Ver X. XX
DSP PFLASH Ver X. XX
IR LEARNING Ver X.XX
NTE 09A55∗∗ Ver X.XX
<DSP DEBUG MENU>
<NETWORK DEBUG MENU>
MAC∗∗:∗∗:∗∗:∗∗:∗∗:∗∗
NET UPDATE CHECK?
ZONE 4 XXXXXXXX
FARO SELECT [XXXXXXX]
HDCP KEY READ [XXX]
LEARNING TEST START?
MODEL [##### ∗∗∗∗ XX]
<VIDEO FACTORY MENU>
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
] button of the remote commander, and changing the content
,
<
Remark
X.XXX: System software version
#####: Model
∗∗∗: Destination
X.XX: Main controller software version
X.XX: Video system controller software version
X.XX: Video processor software version
X.XX: CG-ROM software version
X.XX: DSP controller version
X.XX: DSP serial fl ash software version
X.XX: DSP parallel fl ash version
X.XX: IR learning software version
∗∗: Destination
X.XX: Network processor software version
Not used for the servicing
Menu mode to enter MAC address display. If the [ENTER] but-
Q Q
3 6 7 1 3 1 5
ton of the remote commander is pressed, entering the menu,
and operating the following menu become possible
∗∗:∗∗:∗∗:∗∗:∗∗:∗∗: MAC address
If the [Enter] button of the remote commander is pressed, the
checking result is displayed without connecting to network. OK:
"NET UPDATE CHK OK", Path to MAIN NG: "NET UPDATE
CHK NG M", Path to VIDEO NG: "NET UPDATE CHK NG V",
Path to DSP NG: "NET UPDATE CHK NG D"
Not used for the servicing
XXXXXXX: The selector is switched for the update of the
FAROUDJA update.
[VIDEO]: Video Ucom rewriting,
[UPDATE1]: Faroudja rewriting (main),
[UPDATE2]: Faroudja rewriting (2nd),
[DEBUG1]: Faroudja debug (main),
[DEBUG2]: Faroudja debug (2nd),
Not used for the servicing
Not used for the servicing
Not used for the servicing
Menu mode to enter video calibration menu and DDR access
check menu If the [ENTER] button of the remote commander
is pressed, entering the menu, and operating two the following
menu become possible
co
.
9 4 2 8
] button of the remote commander
0 5 8 2 9 9 4 2 8
m
9 9
9 9