Sony STR-DA5500ES Service Manual Digest page 19

QQ
3 7 63 1515 0
Items
Video calibration
(Video factory menu)
DDR access check
Auto cal mic test
FL display fonts test
FL display test
Super reset
TE
L 13942296513
RAM capacity register/
Error factor register
EERROM debug
Protector on/off
Audio swap
Volume value display (FL/FR)
Volume value display (SL/SR)
Volume value display (CT/SW)
Volume value display (SBL/SBR)
DAC mute fl ag upper
DAC mute fl ag lower
2nd volume value display
Dark out duty
CORTEZ read
Check H.A.T.S. playback
component
H.A.T.S. mode fi x
H.A.T.S. rate control
H.A.T.S. error process
H.A.T.S. error trig
Pass through auto debug
www
.
http://www.xiaoyu163.com
Display
V.CALIBRATION START?
DDR CHECK [XX] sec
SPEAKER OUT [XXXXX]
FL FONT [0x ∗∗ = X]
(all on)
SUPER RESET [XXX]
RAM WATCH MENU
EEPROM [∗∗∗∗] [XX]
PROTECTOR ON/OFF [XXX]
SWAP [XXXXXXXXXXX]
FL∗∗∗∗ FR XXXX
SL∗∗∗∗ SR XXXX
CT∗∗∗∗ SW XXXX
SBL∗∗∗∗ SBR XXXX
DAC MUTE U XXXXXXXX
DAC MUTE L XXXXXXXX
2nd VOLUME XXX
DARK OUT DUTY [XXX%]
CORTEZ READ [XXX]
CHK HATS COMP [XXX]
HATS FIX [XXXXXXX]
HATS RATE [XXXXXX]
HATS ERR PROC [XXX]
HATS ERR TRIG
PASS THRU AUTO DBG
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Procedure:
1. "DVD" is selected by using [INPUT SELECTOR] dial.
2. Connect a color pattern generator to the COMPONENT
VIDEO ASSIGNABLE (INPUT ONLY) IN2 jack (J6007) on
the A-VIDEO board and DVD VIDEO IN jack (J6003) on the
A-VIDEO board.
3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by
automatic operation in pressing the jog switch, and corrects
reference value. In a measurement once, only one of NTSC/
PAL/HD can be measured, repeat NTSC/PAL/HD calibration
from procedure 4.
"Check XXXX V-IN" at display:
Video signal necessary for the measurement while measuring
it last time was not detected and it became an error
Confi rm the input of the video of the terminal connection etc.,
and measure the jog switch again pressing
XX: Time to do access check on DDR (for design evaluation)
(Video factory menu)
XXXXX: Selection of speaker output audio [SOURCE]: normal-
ly mode, [MIC]: mode that output audio from mic from speaker
∗∗: 20 to FE, X: character
Each time [DISPLAY] button to change as follows all on t
test pattern 1 t test pattern 2 t all off t all on
Not used for the servicing
If super reset is performed, "up convert signal level adjustment"
will also be initialized
When EEPROM initialization is required, perform the "memory
clearing mode"
Q Q
3 6 7 1 3 1 5
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
Not used for the servicing
co
.
STR-DA5500ES
9 4 2 8
Remark
0 5 8 2 9 9 4 2 8
m
9 9
9 9
19