Test Mode - Sony STR-DA5500ES Service Manual Digest

STR-DA5500ES
QQ
3 7 63 1515 0
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [2CH/A. DIRECT] and [MEMORY/
ENTER] buttons, press the [POWER] button to turn on the
main power.
2. The message "SWAP MODE !" appears (No change while dis-
played).
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [MUSIC] and [MEMORY/ENTER] but-
tons, press the [POWER] button to turn on the power and
"HISTORY MODE" is displayed.
2. Each time the [ ]/[ ] buttons of the remote commander is
M m
pressed, the item is switched in order as follows.
Items
Number of protector is gener-
ated
Total time until protector is
generated
Sound fi eld
Input Selector
Input mode
Input mode under lock state
Stream under input
Channel information TE
L 13942296513
State of headphone
Volume
EQ setting value
Level collection value
each channel
Total time of power on
www
.
16
http://www.xiaoyu163.com
SECTION 3

TEST MODE

Display
PRCT_COUNT: XXX
TTL_TIME: XXXXH XXM
XXXXXXXXXXXXXXXX
INPUT: XXXXXXXXXX
INMODE: XXXXXXXXXXXX
DSEL: XXXXXXXXXXXXXXX
STREAM: XXXXXXX
CONFIG:XXXXXXX
HEAD PHONES: XXX
VOL: XXXdB
BASS: XXXdB
TREB: XXXdB
Lv FL/FR XXXX/XXXX
Lv SL/SR XXXX/XXXX
Lv CT/SW XXXX/XXXX
Lv BL/BR XXXX/XXXX
TTL_P_ON: XXXXH XXM
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN6751) on the NETWORK board.
2. While pressing the [A.F.D.] and [HDMI IN] buttons, press the
[POWER] button to turn on the main power.
3. The message "DMPORT OK" appears on the fl uorescent indi-
cator tube and enter the digital media port test mode (Confi r-
mation of communication line).
When "NO DETECT", "UART NG" and "UART TO" are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [ ] button on the remote commander is
>
pressed, the connect check and adaptor version check are
switched.
Press the [ ] button on the remote commander, connected
.
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
commander.
NETWORK board
J001
color
DMPORT
pattern
check jig
generator
(Part No.
J-2501-309-A)
Q Q
AF
3 6 7 1 3 1 5
oscillator
XM FACTORY TEST MODE
(US and Canadian models only)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
SIRIUS FACTORY TEST MODE
(US and Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [POWER]
button to turn on the main power.
co
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 kHz L/R, 10 Hz L/R, noise L,
.
noise R, muting are switched.
9 4 2 8
] button on the remote
x
A-VIDEO board
CN6751
J6002
TV
monitor
set
0 5 8 2 9 9 4 2 8
FL/FR
speaker
MAIN board
TM4002
m
9 9
9 9