Advertisement
Step 5 — Set up the IPCP Pro 355 control processor (IPCP models only)
See the IPCP Pro Series Setup Guide, available at www.extron.com, for installation details.
Step 6 — Connect power
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see
A
figure 1,
, on page 1).
Twisted Pair Recommendations for DTP and HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances and
reduce transmission errors:
•
Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron
recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of
400 MHz.
•
Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at
right).
•
Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and
power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.
ATTENTION:
•
Do not connect these connectors to a computer or telecommunications network.
•
Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.
•
DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed
outdoors.
•
L'alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise
l'alimentation DTP à distance ne peut être routée en extérieur.
NOTE:
When using shielded twisted pair cable in bundles or conduits, consider the following:
•
Do not exceed 40% fill capacity in conduits.
•
Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
•
Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
•
Separate twisted pair cables from AC power cables.
RS-232 and IR Over TP Wiring
To pass bidirectional serial command signals between DTP or HDBaseT-compatible devices, connect a control device to the three
leftmost poles (Tx, Rx, and G) of the 5-pole captive screw connector. To transmit and receive IR signals, connect a control device
to the three rightmost poles (G, Tx, and Rx).
NOTE:
Alternatively, RS-232 data can be inserted via Ethernet (see the IN1608 xi Series User Guide for details).
Audio Wiring
Wire the audio input and output connectors as shown
at right. Use the supplied tie wrap to strap the audio
cable to the extended tail of the connector. This does not
apply to the amplified audio output connector on the SA
and MA models.
ATTENTION:
For unbalanced outputs, do not
connect wires to the "-" poles (see the Extron
Audio Wiring Card).
ATTENTION :
Pour les sorties asymétriques, ne
connectez pas de câbles aux pôles « - » (voir le
Audio Wiring Card d'Extron).
NOTE:
The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).
Tip
Ring
Sleeves
Sleeves
Tip
Ring
Balanced Audio Output
Tip
Ring
Sleeves
Sleeve
Tip
Sleeve
Ring
Balanced Audio Input
Pins:
TIA/EIA-T568B
12345678
Pin
Wire Color
Pin
1
1
White-orange
White-green
2
Green
2
Orange
3
White-orange
3
White-green
4
Blue
4
Blue
5
White-blue
5
6
White-blue
Orange
7
White-brown
6
Green
8
Brown
Insert Twisted
7
White-brown
Pair Wires
RJ-45
8
Brown
Connector
No Ground Here
Tip
Tip
No Ground Here
Unbalanced Audio Output
Tip
Do not tin the wires!
Tip
Unbalanced Audio Input
T568A
T
Wire color
Wir
White-
Orange
White-
Blue
White-
Green
White-
Brown
3
Advertisement
