Page 1
10” professional cabinet table saw Model 95112 asseMbly and operation instructions Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com to preVent serious injury, read and understand all warnings and instructions before use.
Making a large panel cut: ................26 Making a dado cut: ..................26 inspection, Maintenance, and cleaning ..........27 troublesHooting ..................29 parts lists and diagraMs ................31 electrical scHeMatic .................. 36 for technical questions, please call 1-800-444-3353. SKU 95112 Page 2...
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. for technical questions, please call 1-800-444-3353. SKU 95112 Page 3...
Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. for technical questions, please call 1-800-444-3353. SKU 95112 Page 4...
Make sure the Saw Blade is balanced, and is not cracked or bent. for technical questions, please call 1-800-444-3353. SKU 95112 Page 6...
Page 7
Saw Blade is pinched or bound tightly by the kerf closing down, the Saw Blade stalls and the motor reaction drives the woodstock rapidly back toward the operator. If the Saw Blade becomes twisted or misaligned in the cut, the teeth at the back for technical questions, please call 1-800-444-3353. SKU 95112 Page 7...
Page 8
Make sure to remove all adjusting wrenches from the table saw before turn- ing it on. for technical questions, please call 1-800-444-3353. SKU 95112 Page 8...
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. saVe tHese instructions for technical questions, please call 1-800-444-3353. SKU 95112 Page 9...
Page 10
220 Volt, grounded, 3-prong, 220 Volt, grounded, 3-prong, twist locK, power cord plug twist locK, power cord plug (not included) (not included) figure a figure a for technical questions, please call 1-800-444-3353. SKU 95112 Page 10...
* based on limiting the line voltage drop to five volts at 150% of the rated amperes. syMbology Double Insulated Volts Alternating Current Canadian Standards Association Amperes n 0 xxxx/min. Underwriters Laboratories, Inc. No Load Revolutions per Minute (RPM) for technical questions, please call 1-800-444-3353. SKU 95112 Page 11...
Hook the back of the Fence Bracket Body (9C) over the Rear Rail (2C). Then lower the front of the Fence Bracket Body into the groove on the Front Rail (1C). (see figure e.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 12...
Arbor Extension horizontally. (see figure f.) Loosen and remove the Arbor Nut (4D) with the Spanner Wrench (85D) provided. Then remove the Blade Flange (5D). (see figure f.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 13...
Page 14
Place the Blade Flange (5D) and Arbor Nut (4D) on the Arbor Extension (6D). Make sure the dome side of the Blade Flange faces out from the Saw Blade (86D). Then, tighten the Arbor Nut securely. (see figure f.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 14...
Place a framing square (not included) against the Saw Blade (86D), with the long end under the Fence Bracket Body (9C) at the front. Then, note the distance. (see figure g.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 15...
Align the front mounting slot of the Spreader (6B) with the threaded mounting hole of the Rear Trunnion Bracket (58D). Secure the front of the Spreader in place, using one 8mm Hex Bolt (50E) and one 8mm Hex Nut (51E). (see figure H.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 16...
Loosen the 8mm Washer (43E) and 8mm Hex Head Bolt (44E) on the front mounting slot of the Spreader (6B) and move the front of the Spreader up or down. (see assy. diagrams b and e.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 17...
Dust Port by tightening the hose clamp. note: The vacuum hose must have an inside diameter of 4” to properly fit onto the Dust Port. (see figure i.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 18...
Lock the Saw Blade (86D) height in position by turning the Lock Knob (26E) clock- wise about three turns. iMportant: Do not overtighten. Only a small amount of pressure is necessary to lock the Height Hand Wheel (36E) securely. (see figure j.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 19...
Lock the Saw Blade (86D) angle in position by turning the Lock Knob (26E) clockwise about three turns. iMportant: Do not overtighten. Only a small amount of pres- sure is necessary to lock the Tilting Hand Wheel (30E) securely. (see figure j.) for technical questions, please call 1-800-444-3353. SKU 95112 Page 20...
Table (8E). When using the left Groove, hold the workpiece firmly against the Miter Gauge (4A) with your left hand and grip the Handle (1A) with your right hand. When for technical questions, please call 1-800-444-3353. SKU 95112 Page 21...
Table Saw to cut faster or greater than its capacity. When the cut is completed, press the Power Switch (17E) to its “off” position. Then, unplug the Power Cord Plug from its electrical outlet. for technical questions, please call 1-800-444-3353. SKU 95112 Page 22...
Table (8E). When using the left Groove, hold the workpiece firmly against the Miter Gauge (4A) with your left hand and grip the Handle (1A) with your right hand. When for technical questions, please call 1-800-444-3353. SKU 95112 Page 23...
Tilting Hand Wheel (30E). Then, retighten the Lock Knob. Install the Rip Fence assembly on the right side of the Saw Blade (86D) at the correct distance from the Saw Blade for the cut. for technical questions, please call 1-800-444-3353. SKU 95112 Page 24...
Allow the Saw Blade (86D) to spin up to full speed before feeding the workpiece into the Saw Blade. Hold the workpiece firmly against the Miter Gauge (4A), and push the workpiece into the Saw Blade (86D). for technical questions, please call 1-800-444-3353. SKU 95112 Page 25...
Arbor Extension (83D) to perform dado cuts. These parts will need to be ordered to perform dado cuts. Do not attempt to alter the Table Saw components to perform dado cuts. for technical questions, please call 1-800-444-3353. SKU 95112 Page 26...
Head Bolts (72D) on the Motor Mount Plate, and raise the Motor Mount Plate (71D) to release tension on the V-Belts. Remove the old V-Belts (82D). Place the V-Belts (82D) in position on the Drive Pulley (40D) and the Motor Pul- ley (80D). for technical questions, please call 1-800-444-3353. SKU 95112 Page 27...
Page 28
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. for technical questions, please call 1-800-444-3353. SKU 95112 Page 28...
Have the power cord or power switch damaged. replaced by a qualified technician. Table saw is noisy when Motor needs attention. Have the motor checked by a qualified running. technician. for technical questions, please call 1-800-444-3353. SKU 95112 Page 29...
Page 30
Rail” section on page 15.) Clean and lubricate rails. Wood edges away from rip Rip fence is misaligned. See “To Check Rip Fence and Saw fence when ripping. Blade Alignment” section on page 15. for technical questions, please call 1-800-444-3353. SKU 95112 Page 30...
& asseMbly diagraM b - guard asseMbly part description Q’ty part description Q’ty part description Q’ty Push Nut Spring Anti-Kickback Pawl Clear Blade Guard Spreader Snap Ring Guard Support Spacer for technical questions, please call 1-800-444-3353. SKU 95112 Page 31...
Page 32
Plastic Screw Hex Head Screw (M8 x 30mm) Fence End Cover Spacer Rail End Cover Plastic Pad Allen Wrench (4mm) Socket Head Screw (M5 x 15mm) Allen Wrench (5mm) Lock Knob for technical questions, please call 1-800-444-3353. SKU 95112 Page 32...
Page 33
Saw Blade (Not Included) Snap Ring (R22) Set Screw Wrench (5mm) Bearing Washer Set Screw Wrench (3mm) Bearing Spanner (12 x 14 Wrench) Washer Spanner (17 x 19 Wrench) Lock Nut (20mm) for technical questions, please call 1-800-444-3353. SKU 95112 Page 33...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 for technical questions, please call 1-800-444-3353. SKU 95112 Page 36...