Page 1
TABLE TILT BANDSAW 12” - 3/4 HP Model 94652 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com...
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 2...
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 3...
Page 4
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 4...
WARNING! Keep hands and fingers away from cutting area and Saw Blade. Never leave the Bandsaw unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 5...
Page 6
Failure to do so may result in off-cut binding against the Saw Blade. Always unplug the Bandsaw from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 6...
Page 7
If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 7...
Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) THIS PRODUCT DOES NOT 120 VOLT, USE A GROUNDED, 2-PRONG PLUG ELECTRICAL OUTLETS FIGURE B For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 8...
5.1 – 7.0 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 * Based on limiting the line voltage drop to five volts at FIGURE C 150% of the rated amperes. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 9...
Page 10
With assistance, place the Table (6) upon the two Supports (128). (See Figure D, next page.) Align the four threaded mounting holes in the Table (6) with the four mounting holes in the two Supports (128). (See Figure D.) For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 10...
Page 11
SERRATED LOCK WASHER (68) POINTER (129) CLAMPING HANDLE HEX BOLT (133) (71) FIGURE E FIGURE D FIGURE F FIGURE G SAW BLADE HEX BOLT (35) (123) T-SQUARE (NOT INCLUDED) STOPPER (124) For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 11...
Page 12
To Attach A Vacuum Hose To The Dust Chute: The Dust Chute (136) has an outside diameter of 3-3/4”. To attach a vacuum hose (not included) to the Dust Chute, slide the vacuum hose onto the Dust For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 12...
Switch to its “OFF” position. Then, remove and store the Safety Key in a safe location. (See Figure K.) POWER SWITCH (98) SAFETY KEY FENCE (8) CLAMP HANDLE (19) BELT TENSIONING HAND WHEEL (62) FIGURE K For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 13...
Page 15
Insert the Safety Key into the Power Switch (98), and turn the Power Switch to its “ON” position. NOTE: When turning on the Bandsaw, allow the Saw Blade (35) to reach its full speed before feeding the workpiece into the Blade. (See Figure K.) For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 15...
Motor of the Bandsaw and will not produce a satisfactory cut. Replace with a new Saw Blade when needed. To replace a Saw Blade: A. NOTE: Make sure to wear heavy duty work gloves to avoid accidental cuts For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 16...
Page 17
(97) clockwise. (See Figure M.) BLADE TENSION ADJUSTING KNOB (97) UPPER WHEEL (87) TABLE INSERT BLADE GUIDE HOUSING (25) SAW BLADE (35) TABLE (TOP VIEW) BODY (32) LOWER WHEEL (42) FIGURE M For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 17...
Page 18
Then, re-tighten the Nut (24). (See Figure N.) Adjust the second and third Blade Guide Bearings in the same manner. SAW BLADE (35) BLADE GUIDE BEARING BLADE GUIDE HOUSING (25) SMALL THRUST (23) FIGURE N For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 18...
Page 19
H. Turn the Belt Tensioning Hand Wheel (62) clockwise to increase tension on the new V-Belt. (See Figure L.) FIGURE O CIRCLIP (39) AND BEARING (40) PULLEY (44) TENSION PULLEY (53) V-BELT (52) OUTER SHIFT WHEEL (50) LOWER WHEEL (42) For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 19...
V-Belt tension too high. Reduce tension on V-Belt. Blade is too coarse for work. Replace with finer tooth Blade. Blade is too fine for work. Replace with coarser tooth Blade. For technical questions, please call 1-800-444-3353 SKU 94652 PAGE 20...