1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Saw
  5. 94443
  6. Assembly and operating instructions manual

Central Machinery 94443 Assembly And Operating Instructions Manual

8 in. wet tile saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
8 in. Wet Tile Saw
94443
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright
2006 by Harbor Freight Tools
. All rights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 94443

Summary of Contents for Central Machinery 94443

  • Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.

  • Page 2: Specifications

    Tank (31) to enter the Motor (22). Never move the tool with water inside the tank. Ensure that the Overfill Plug (53) remains unclogged at all times. Water entering a power tool will increase the risk of electric shock and may damage the tool. SKU 94443 For technical questions, please call 1-800-444-3353 Specifications...

  • Page 3: Personal Safety

    15. Use safety equipment. Always wear eye protection and full face shield when using this saw. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

  • Page 4: Specific Safety Rules

    Always wear ANSI-approved safety impact eye goggles when using the tool. Using personal safety devices reduce the risk for injury. Safety impact eye goggles and other safety equipment are available from Harbor Freight Tools. Periodically check to be sure the Locking Arbor Nut (38) is tight, and the Blade is securely fastened to the Arbor Shaft.

  • Page 5: Grounded Tools: Tools With Three Prong Plugs

    The plug and outlet should look like those in the following illustration. (See Figure A.) DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS Figure B NOTE: The 93334 Wet Saw uses a grounded three-prong plug. SKU 94443 For technical questions, please call 1-800-444-3353 GROUNDING Tools marked “Double Insulated”...

  • Page 6: Extension Cords

    Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 94443 For technical questions, please call 1-800-444-3353 EXTENSION CORDS...
  • Page 7 When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Before using your 8” Wet Tile Saw for the first time, you must install the Blade and Blade Guard, and fill the Water Tank with water.

  • Page 8: Operation

    The tub has enough water to keep the blade wet. e) The Access Cover is in place. f) The wet saw is positioned on a solid, level surface which is sturdy enough to safely support the tool and your work materials.
  • Page 9 Do not use this saw over 30 minutes each hour, or longer than 20 minutes continuously. This will help prevent overheating of the saw, and extend saw life.
  • Page 10 Holding the tile firmly against the fence and the bevel accessory, pass the tile under the Blade to cut. SKU 94443 For technical questions, please call 1-800-444-3353 The Bevel Cutting Attachment Page 10...

  • Page 11: Maintenance

    Return the Sliding Table to its forward position, and move the Locking Switch (54) to the “Lock” position. Return the Support Bar (50) to its forward position. Wind up the Power Cord (10) and store the Saw in a safe place. 1) Does not make a straight cut: a) Check blade to be sure it is on tight.

  • Page 12: Parts List

    PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 94443 For technical questions, please call 1-800-444-3353 Parts List...

  • Page 13: Assembly Drawing

    Assembly Drawing SKU 94443 For technical questions, please call 1-800-444-3353 Page 13...

  • Page 14: Limited 90-Day Warranty

    LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase.

Table of Contents