Page 1
16 INCH VARIABLE SPEED SCROLL SAW 93012 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Copyright 2007 by Harbor Freight Tools .
Distractions can cause you to lose control. Protect others in the work area from de- bris such as chips and sparks. Provide barriers or shields as needed. REV 05e, 05i Page 2 SKU 93012 For technical questions, please call 1-800-444-3353...
Remove adjusting keys or wrenches before turning the power tool on. wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. Page 3 SKU 93012 For technical questions, please call 1-800-444-3353...
Page 4
SPECIFIC SAFETY RULES FOR THIS PRODUCT Maintain labels and nameplates on the Scroll Saw. These carry important infor- mation. If unreadable or missing, contact Harbor Freight Tools for a replacement. Page 4 SKU 93012 For technical questions, please call 1-800-444-3353...
Page 5
They have a tendency to roll while being cut causing the Blade to “bite.” If the blade binds in the workpiece when backing out of the cut, immediately turn the saw power Off and carefully back material off Blade. Page 5 SKU 93012 For technical questions, please call 1-800-444-3353...
The plug and outlet should look like those in the following illustration. 3-Prong Plug and Outlet (See 3-Prong Plug and Outlet.) Page 6 SKU 93012 For technical questions, please call 1-800-444-3353...
5.1 – 7.0 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 TABLE A * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Page 7 SKU 93012 For technical questions, please call 1-800-444-3353...
Page 8
Assembly Drawing and Parts List at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. REV 02/07 Page 8 SKU 93012 For technical questions, please call 1-800-444-3353...
Insert the Blade through the hole in the workpiece and the Saw Table (53). Reinstall the Blade and properly adjust tension. Refer to page 13. Make sure Blade teeth are facing forward and down. Page 10 SKU 93012 For technical questions, please call 1-800-444-3353...
13. The workpiece will come with it. Place a flat bladed screwdriver in the cut and force it open. Remove the Saw Blade. Reinstall the Saw Blade on the machine as described on page 13. Page 11 SKU 93012 For technical questions, please call 1-800-444-3353...
The next day, repeat steps 1 to 4 on the other side of the Scroll Saw. Wipe up excess oil with a cloth. REV 02/07 Page 12 SKU 93012 For technical questions, please call 1-800-444-3353...
Same as above except for wood. 0.11” 0.02” Cuts wood from 1/8 to 1-1/2” thick. Extra thin cuts on soft woods and 0.095” 0.1” other materials up to 1/4”. REV 02/07 Page 13 SKU 93012 For technical questions, please call 1-800-444-3353...
Check motor mounting hardware is secure. Blade not in line with Blade holders not aligned. Loosen Hex Bolts and re-align Upper and arm motion Lower Blade Holders. Tighten Hex Bolts. REV 09/05 Page 14 SKU 93012 For technical questions, please call 1-800-444-3353...
ITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. REV 09/05 Page 15 SKU 93012 For technical questions, please call 1-800-444-3353...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 Page 17 SKU 93012 For technical questions, please call 1-800-444-3353...