Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kendal Lighting AC-20070
Summary of Contents for Kendal Lighting AC-20070
-
Page 1: Installation Instructions
READ AND SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS Model: AC-20070 KENDAL LIGHTING Kendal Lighting (BC) Inc. #110, 6780 Dennett Place Delta, BC V4G 1N4 Canada Tel: (604) 952-5510 Fax: (604) 952-5513 C.E.T.L. LISTED MODEL: CF570ER-BRD Weight of Fan: 12.30Kgs... -
Page 2: Tools And Materials Required
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items; a. Hanger bracket b. Canopy c. Canopy cover d. -
Page 3: Safety Rules
3. SAFETY RULES 1. To reduce the risk of electric shock, insure 8. To avoid personal injury or damage to the electricity has been turned off at the circuit fan and other items, be cautious when breaker or fuse box before beginning. working around or cleaning the fan. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. -
Page 5: Hanging The Fan
5. HANGING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Pass the 120-volt supply wires through CUL Listed electrial the center hole in the ceiling hanger bracket as shown in Fig. 5. Washers Ceiling Step 2. -
Page 6: Make The Electric Connections
6. MAKE THE ELECTRIC CONNECTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the Outlet box main fuse box before wiring. White (neutral) Black (hot) Step 1. (Figure 8) Motor to House Supply Wires Green or bare Electrical Connections: Connect the black wire copper (ground) from the fan to the black (hot) wire from the... -
Page 7: Finishing The Installation
8. FINISHING THE INSTALLATION Step 1. Tuck connections neatly into ceiling outlet box. Outlet box Step 2. Slide the canopy up to hanger bracket Hanger and place the key hole on the canopy over the bracket Screws screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. - Page 8 10. INSTALLATING THE MOUNTING PLATE Step 1. Remove 1 of 4 screws from the mounting ring and loosen the other 3 screws. (Do not remove) Step 2. Place the key holes on the mounting plate over the 3 screws previously loosened Mounting from the mounting ring, turn mounting plate ring...
-
Page 9: Attaching The Glass Shade
12. ATTACHING THE GLASS SHADE Install the glass shade by carefully turning it clockwise until snug. DO NOT OVERTIGHTEN. (Fig. 15) Glass shade Figure 15 13. INSTALLING THE TRANSMITTER HOLDER Attach the remote control holder with the two remote control holder mounting screws. (Fig.16) Figure 16... -
Page 10: Ceiling Fan
14. Operation of your Ceiling Fan: Step 1: Make sure power is restored to the fan unit as during installation it was most likely turned off at the wall switch or breaker box. Note: The fan is controlled by the remote system only. - Page 11 Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans and so on. NOTE: To operate the reverse function on this fan, press the reverse button while the fan is Warm weather - (Forward) A downward airflow creates a cooling effect as shown in Fig.
-
Page 12: Care Of Your Fan
15. CARE OF YOUR FAN Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. -
Page 13: Troubleshooting
16. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. 3. Turn power off at the wall for 20 seconds and then turn power back on to reset system.