Hide thumbs Also See for RoofTop R240:
Table of Contents

Advertisement

The device incorporates a host control device manufactured by Nokia into which a
Symbol PCMCI radio LAN card is installed.
The following Users Manuals are included:
1) Manual from Nokia for End User
2) Manual from Nokia for Professional Installation
3) Manual from Nokia for User Installation
Users Manual For Nokia
FCC ID: NPD-R240-V01

Advertisement

Table of Contents
loading

Summary of Contents for Nokia RoofTop R240

  • Page 1 Users Manual For Nokia FCC ID: NPD-R240-V01 The device incorporates a host control device manufactured by Nokia into which a Symbol PCMCI radio LAN card is installed. The following Users Manuals are included: 1) Manual from Nokia for End User...
  • Page 2 Wireless Router User Guide...
  • Page 3 2.4 BHz radio spectrum. Your Nokia RoofTop Wireless Router not only provides you with fast “always-on” internet access, but is also an integral part of the network infrastructure. Some routers may rely on others to reach the internet. For this reason it is very important that you always keep your router powered ON, even if you are not using it.Your router may be forwarding and...
  • Page 4 4. Ethernet cable 5. Network/Power Unit...
  • Page 5 Warnings and Safety Instructions Important User Information The Nokia RoofTop Wireless Router was designed and manufactured to meet strict quality and safety standards. It complies with the FCC rules, Part 15, Part 68 and with 21 CFR 1040.10 and 1040.11.
  • Page 6 Instructions • Read and follow all safety and operating instructions • Heed all precautions and warnings in the instructions and on the equipment • Keep instructions for future use Hazard Warnings Environment - Do not place the Network/Power Unit in a very cold, The unit should be dusty, wet or high humidity environment.
  • Page 7 All grounding should be performed by a professional. Accessories ? ? Use only Nokia approved accessories for all installations. Cleaning the Unit ? ? Clean the Network/Power Unit with a dry cloth or paper towel. Do not use any liquids to clean the unit.
  • Page 8 Network/Power Unit Front Panel Your Network/Power Unit has LEDs which indicate the functioning of your unit. If you are experiencing problems with your wireless router, call your Internet Service Provider’ s service desk. The service personnel may ask you to refer to the LEDs on the Network/Power Unit. When you call, make sure you can see the LEDs to be able to give the information to the service personnel.
  • Page 9 3. Network Bottom Panel Connections Bottom Panel Connections 1. HomePNA 2.0 interface: A standard phone jack (RJ-11) 2. Ethernet interface: A standard 10/100 BaseT Ethernet jack (RJ-45) 3. Router outdoor unit connection : This connector connects directly to your outdoor wireless router. Connecting the Wireless Router to Your PC, LAN or Home PNA Your wireless router is capable of providing internet access for a single PC via a direct connection or to multiple PCs via Local Area Network (LAN) or via Home PNA.
  • Page 10 Nokia provides technical support only for network operators and authorized resellers. Your Internet Service Provider (ISP) provides technical support for subscribers to a Nokia network. If you experience problems with your service or have any questions regarding the performance of your wireless router, please contact the ISP that is...
  • Page 11 Disclaimer Nokia is the manufacturer of the wireless router and provides no warranty service and repair. Nokia RoofTop wireless routers are provided "AS IS" with no warranty. NOKIA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE.
  • Page 12 Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013. TRADEMARKS Nokia and Nokia RoofTop are registered trademarks of Nokia Corporation. Other products mentioned in this document are trademarks or registered trademarks of their respective holders. REGULATORY INFORMATION...
  • Page 13 functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. Compliance in Canada Emission Standards Canadian compliance (Industry Canada) When tested with at least one intended host: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference-causing equipment entitled "Digital Apparatus", ICES-003 of the Canadian Department of Communications.
  • Page 14 Wireless Router User Guide...
  • Page 15 2.4 BHz radio spectrum. Your Nokia RoofTop Wireless Router not only provides you with fast “always-on” internet access, but is also an integral part of the network infrastructure. Some routers may rely on others to reach the internet. For this reason it is very important that you always keep your router powered ON, even if you are not using it.Your router may be forwarding and...
  • Page 16 4. Ethernet cable 5. Network interface and power supply unit...
  • Page 17 Warnings and Safety Instructions Important User Information The Nokia RoofTop Wireless Router was designed and manufactured to meet strict quality and safety standards. It complies with the FCC rules, Part 15, Part 68 and with 21 CFR 1040.10 and 1040.11.
  • Page 18 Instructions • Read and follow all safety and operating instructions • Heed all precautions and warnings in the instructions and on the equipment • Keep instructions for future use Hazard Warnings Environment - Do not place the network interface and power supply The unit unit in a very cold, dusty, wet or high humidity environment.
  • Page 19 All grounding should be performed by a professional. Accessories ? ? Use only Nokia approved accessories for all installations. Cleaning the Unit ? ? Clean the network interface and power supply unit with a dry cloth or paper towel.
  • Page 20 Network Interface & Power Supply Unit Front Panel Your network interface and power supply unit has LEDs which indicate the functioning of your unit. If you are experiencing problems with your wireless router, call your Internet Service Provider’ s (ISP’ s) service desk. The service personnel may ask you to refer to the LEDs on the network interface and power supply unit.
  • Page 21 3. Network Bottom Panel Connections Bottom Panel Connections 1. HomePNA 2.0 interface: A standard phone jack (RJ-11) 2. Ethernet interface: A standard 10/100 BaseT Ethernet jack (RJ-45) 3. Router outdoor unit connection : This connector connects directly to your outdoor wireless router. Connecting the Wireless Router to Your PC, LAN or Home PNA Your wireless router is capable of providing internet access for a single PC via a direct connection or to multiple PCs via Local Area Network (LAN) or via Home PNA.
  • Page 22 Nokia provides technical support only for network operators and authorized resellers. Your Internet Service Provider (ISP) provides technical support for subscribers to a Nokia network. If you experience problems with your service or have any questions regarding the performance of your wireless router, please contact the ISP that installed...
  • Page 23 Disclaimer Nokia is the manufacturer of the wireless router and provides no warranty service and repair. Nokia RoofTop wireless routers are provided "AS IS" with no warranty. NOKIA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE.
  • Page 24 Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013. TRADEMARKS Nokia and Nokia RoofTop are registered trademarks of Nokia Corporation. Other products mentioned in this document are trademarks or registered trademarks of their respective holders. REGULATORY INFORMATION...
  • Page 25 functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. Compliance in Canada Emission Standards Canadian compliance (Industry Canada) When tested with at least one intended host: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference-causing equipment entitled "Digital Apparatus", ICES-003 of the Canadian Department of Communications.
  • Page 26 Manual – Professional Installation...
  • Page 27 Nokia RoofTop Wireless Router ™ (R240/ R240A) Hardware Installation Guide DN00290079 - 2nd Draft December, 2000...
  • Page 28 —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Any modifications made to the unit, unless expressly approved by Nokia could void the user’s authority to operate the equip- ment.
  • Page 29 FCC Rules and Regulations - Part 68 This equipment complies with Part 68 of the FCC Rules. The FCC Part 68 Label is located on the rear panel of the Network/ Power Unit unit. This label contains, among other information, the FCC Registration Number and Ringer Equivalency Number (REN) for this equipment.
  • Page 30 Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by a user to this equipment, or equipment malfunctions, may give the telephone communications companu cause to request the user to disconnect the equipment. Notice: The Ringer Equivalent Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.
  • Page 31 POSE OR INFRINGEMENT, INCLUDING ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADEMARKS OR OTHER RIGHTS. THERE IS NO WARRANTY BY NOKIA THAT THE INSTRUCTIONS CONTAINED IN THE GUIDE WILL MEET YOUR REQUIREMENTS. THERE IS NO WARRANTY BY NOKIA THAT THE INSTRUCTIONS AND STATEMENTS CONTAINED IN THE GUIDE OR ITS CONTENT ARE TRUE, ACCURATE OR COMPLETE.
  • Page 33: Table Of Contents

    5.2.1 Directional antenna..... . . 37 5.2.2 To prepare and install grounding ... . 41 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 34 ..... . 61 Regulatory safety requirements APPENDIX C ....63 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 35 Contents Tool requirements APPENDIX D ......65 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 36 Contents Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 37: About This Document

    About this document CHAPTER 1 1.1 Introduction This document explains the procedures necessary to install the Nokia Rooftop Wireless Router. In addition to the installation instructions, this document also describes the tasks required prior to installation. The actual instructions for installation commence in Chapter 5.0...
  • Page 38 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 39 Introduction Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 40 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 41: Safety Issues

    CHAPTER 2 2.1 Introduction It is important, when installing the Nokia Wireless Router, that the unit is not installed where it could be either damaged by its environment, or pose a hazard for the user. In this respect, when installing the unit be aware of the following Hazard Warnings and Regulatory Safety Requirements Nokia RoofTop™...
  • Page 42: Hazard Warnings

    • Because antennas and wireless routers are elevated metal objects with connections to ground, they attract lightning. Attach an effective ground to the antenna and router to provide a safe path for the lightning. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 43: Regulatory Safety Requirements

    Co-location - In order to avoid degradation of performance, it is recommended that the antennas be placed at least one meter (3 feet) apart. • The Nokia RoofTop™ Wireless Router and its associated components must be installed and configured by a trained professional. Awaiting table from Nokia SMEs NOTE: Nokia RoofTop™...
  • Page 44 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 45: Site Survey

    For a directional link with a single antenna, there is only one RF path. For an omnidirectional antenna, determine all RF paths. The RF path can be determined by knowing the relative bearing from the current site to adjacent sites. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 46 Select the antenna type to be used The wireless router is supplied with an omnidirectional antenna, but on rare occasions a directional antenna may need to be used, depending on area and topography. (See also Section 3.1.2 Antenna selection, below) Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 47: Line Of Sight Analysis

    Visual line of sight exists when an imaginary straight line can be drawn between two antennas without passing through any physical obstructions. Verifying visual line of sight is the first step in planning the Nokia Wireless Router System installation. Observation points must be high enough to allow the viewer to see over ground based obstructions.
  • Page 48: Antenna Selection

    3.1.2 Antenna selection 3.1.2.1 General In most installations, it is not necessary to be concerned about antenna selection. The Nokia Wireless Router is supplied with an omnidirectional antenna which is good for most installations. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 49 Directional antennas are useful for long distance or point-to-point NOTE: contacts, but prevent future growth of the network, by preventing the wireless router from repeating signals to other units. They should be used only when where an omnidirectional antenna will not work. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 50 Directional antennas - radiation pattern side view In Nokia Wireless Router Networks, use a directional antenna only if: • There are numerous obstructions in the area • The nearest router is a considerable distance away • The router is in a location where it does not need to route traffic for other subscribers and itself requires a maximum link distance to the neighboring router.
  • Page 51: Planning The Installation

    The Multiwire connection (between the router and the Network/ Power Unit) The Network/ Power Unit The grounding (where required) The indoor connections between the Network/Power Unit and the computer(s) in the property. NOTE: Digital picture of components to be inserted here Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 52: To Find A Location For The Router

    It is acceptable to use the TV antenna pole already installed. If the TV antenna is used, be sure to loosen the antenna mounting, slide the TV antenna down the pole leaving sufficient room to mount the router at the top of the pole. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 53: To Plan The Network/Power Unit Location

    Test the existing grounding system at the property. Where the existing grounding is not acceptable, consider... • Route of the grounding cable from the router, avoiding other pipes, down spouts etc • Location for the grounding rod Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 54 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 55: Outdoor Installation

    • A shielded multiwire cable containing 7 twisted pairs of wires. This is used to connect the wireless router with the NPU. Nokia provides several different lengths of cable with D-Connectors already installed to the end of the cable. The multiwire cable must be Cat-5 cable, size AWG 22 or 24.
  • Page 56 “Wall plate” for cable feed-through into house. - Check with Petri 5.1.1.1 RF-cable for non-integral antenna Nokia provides a flexible jumper cable for the connection between a router and a directional antenna. NOTE: When using an RF cable instead of the integral antenna, a special RF adapter must be used (Nokia Code: WR 468993A).
  • Page 57: To Install The Router

    Where the installation is for a directional antenna, mount the router bracket approximately 18 inches below the top of the mast. NOTE: For directional antenna information, see Section 5.2.1 Directional antenna. Router bracket fixed to mast Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 58 Attach the omnidirectional antenna by screwing it into the top of the wireless router. Carefully guide the antenna down onto the RF pin to prevent the pin being bent out of shape.Ensure secure connection, but do not overtighten (Definition of “overtighten”). Attach the omni-directional antenna Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 59 Use ties/ tape about every two feet down the length of the mast. Always cover the cable ties with electrical tape to prevent excess pressure on the D-connector should the cable tie fail. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 60 Attach mounting bracket to back of router. Ensure that the bolt fits correctly and is not cross threaded. There is no need to tighten the bolt, play is required to attach the router to the mast mounting bracket. Attach mounting bracket to router Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 61 To install the router Attach the front panel of the wireless router. Attach front panel of wireless router Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 62 Be careful not to overtighten the bolt. Overtightening of the bolt will strip the thread in the back of the aluminum casting of the wireless router. Slide the router mount onto the mast bracket Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 63: Directional Antenna

    Using the Jumper Cable (pigtail), connect the wireless router to the directional antenna ensuring that the connections are properly tight, but do not overtighten. Connect the wireless router to the directional antenna with the jumper cable Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 64 Remove plastic backing from the tape Stretch and apply the tape in the direction of the connector thread to ensure that the connector does not come loose during the weatherproofing process. Stretching tape Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 65 Covering the directional antenna connection with weatherproof tape NOTE: Squeeze the tape against the antenna and connector to remove any air gaps and apply the tape so that it overlaps half of the width of the tape. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 66 Attach the mast (where applicable) to the property securely and as appropriate to the requirements of the site. Ensure that direction of the antenna and its’ polarization are correct aligned. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 67: To Prepare And Install Grounding

    Locate the lightning arrestor close to the point of entry to the home. Provide a good, very low resistance wire connection from the wireless router to the ground. Use #12 copper wire connected to the router grounding clamp and a ground rod next to the building. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 68 Grounding of router and NPU Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 69: Routing The Cable Into The Property

    18 to 24 inch intervals and are not unsightly. Make sure that there is a “drip loop” at the point of entry to prevent water ingress into the property. Seal any drilled holes using silicon sealant. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 70 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 71: Indoor Installation

    Indoor installation CHAPTER 7 7.1 Introduction 7.1.1 Components to be installed The Indoor portion of the Nokia Wireless Router System consists of: • Network Power Unit (NPU) • Ethernet or home PNA connection cable Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 72: Network/ Power Unit (Npu)

    HomePNA 2.0 interface, a standard phone jack (RJ-11) Ethernet interface, a standard 10/100 BaseT Ethernet jack (RJ-45) Router outdoor unit connection: A multiwire cable from Router unit is connected to this. The connector is a punch down connector inside the unit. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 73: To Install The Network/ Power Unit

    7.3 To install the Network/ Power Unit This chapter is incomplete. Awaiting further technical NOTE: information and illustrations from Nokia SMEs Trim back the multiwire cable insulation taking care not to cut any of the smaller wires in the cable.
  • Page 74 Power on, but no ethernet packets seen Slow Flash Waiting for the router to complete boot cycle Intermittent Flash Off during packet transmit or receive. Otherwise ON No power or the router is not functioning (IROS is off) Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 75 Head and the AirHead is less than, or equal to 3 Hops Fast Flash The unit has 1 neighbor with a 2 Mbps path to the AirHead and the AirHead is less than, or equal to 3 Hops None of the above Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 76: Connection Options

    All these options are described in more detail below. 7.3.2 Network Use a standard Ethernet Cable with an RJ45 connector at the Wireless Router and the appropriate connector at the LAN Ethernet connection. Network Connection Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 77: Direct Personal Computer Connection

    PC. Direct PC connection Changing the Ethernet configuration from a LAN connection to a NOTE: direct PC connection requires changing from a standard Ethernet cable to a crossover cable. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 78: Home Pna Connection

    7.3.4 Home PNA connection • Connect the phone cable between a Network/ Power Unit HomePNA connection and RJ11 phone jack or directly to the PC- HomePNA adapter. • Connect PC to adapter according to manufacturers instructions. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 79: Configuring The End User Pc

    8.1 Introduction After the router installation is complete, the customers PC needs to be configured for use with the Nokia Wireless Router system. The customer may carry out the configuration themselves, or the installer may be required to carry out the configuration for the customer. This depends upon the agreement with the Internet Service Provider.
  • Page 80: To Configure The Customer's Personal Computer

    Address and Subnet Mask in accordance with information provided by the ISP. 3. In the Default Gateway field, enter the IP address of the default gateway, provided by the ISP. 8.1.2 To configure the customer’s Macintosh Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 81: Post Installation Testing

    2. Turn on the customer's PC. Wait for 3-5 minutes to allow the router to anchor to the network. Check the LEDs to indicate active internet connection, according to Chapter 7- Indoor installation. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 82 6. Where there are problems with download or speed of connection, check the installation first. If this does not solve the problem, then contact the ISP. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 83 Introduction Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 84 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 85 The wiring for an Ethernet Crossover cable for 10Base-T is as follows: RJ45 Plug Pin 1 (Tx+) to Pin 3 (Rx+) Pin 2 (Tx-) to Pin 6 (Rx-) Pin 3 (Rx+) to Pin 1 (Tx+) Pin 6 (Rx-) to Pin 2 (Tx-) Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 86 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 87: Technical Specifications

    Technical specifications APPENDIX B This appendix describes technical specifications for Nokia RoofTop™ Wireless Router Models R240 & 240A Outdoor-Mounted Unit. Data Capacity per Cell 12 Mbps (6x2 Mbps per channel) AirHeads per Cell Up to 6 Routers per Cell Up to 240...
  • Page 88 " Diameter Power Consumption 16 Watts @ 120 VAC External Power Supply Management Nokia Wireless Router Manager, SNMP MIB II, Telnet Internet Protocols IP, TCP, UDP, ICMP, RIPv1, RIPv2, SNMP, TFTP, IGMP, ARP, Proxy-ARP, Telnet, DHCP Relay, DHCP Server, NAT.
  • Page 89: Regulatory Safety Requirements

    1 meter apart horizontally, unless more than 1 meter vertical separation is used. Antennas 16 cm 22 cm 27 cm 31 cm 35 cm 38 cm Distance Inches 7 inches 9 inches 11 inches 13 inches 14 inches 15 inches Nokia RoofTop™ Wireless Routing Installation Guide...
  • Page 90 Nokia RoofTop™ Wireless Routing Installation Guide...
  • Page 91: Tool Requirements

    Tool requirements APPENDIX D Nokia RoofTop™ Wireless Routing Installation Guide...
  • Page 92 Nokia RoofTop™ Wireless Routing Installation Guide...
  • Page 93 Manual – User Installation...
  • Page 94 Nokia RoofTop Wireless Router ™ (R240/ R240A) Hardware Installation Guide (self-install)
  • Page 95 —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Any modifications made to the unit, unless expressly approved by Nokia could void the user’s authority to operate the equip- ment.
  • Page 96 FCC Rules and Regulations - Part 68 This equipment complies with Part 68 of the FCC Rules. The FCC Part 68 Label is located on the rear panel of the Network/ Power Unit. This label contains, among other information, the FCC Registration Number and Ringer Equivalency Number (REN) for this equipment.
  • Page 97 Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by a user to this equipment, or equipment malfunctions, may give the telephone communications company cause to request the user to disconnect the equipment. Notice: The Ringer Equivalent Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.
  • Page 98 LAR PURPOSE OR INFRINGEMENT, INCLUDING ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADEMARKS OR OTHER RIGHTS. THERE IS NO WARRANTY BY NOKIA THAT THE INSTRUCTIONS CONTAINED IN THE GUIDE WILL MEET YOUR REQUIREMENTS. THERE IS NO WARRANTY BY NOKIA THAT THE INSTRUCTIONS AND STATEMENTS CONTAINED IN THE GUIDE OR ITS CONTENT ARE TRUE, ACCURATE OR COMPLETE.
  • Page 100 6.1.1 Components to be installed ....33 6.2 Network/ Power Unit (NPU) ....34 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 101 ......... 45 Technical Specifications APPENDIX B ..... 47 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 102: About This Document

    About this document CHAPTER 1 1.1 Introduction This document explains the procedures necessary to install the Nokia Rooftop Wireless Router. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 103 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 104: Safety Issues

    CHAPTER 2 2.1 Introduction It is important, when installing the Nokia Wireless Router, that the unit is not installed where it could be either damaged by its environment, or pose a hazard for the user. In this respect, when installing the unit be aware of the following Hazard Warnings and Regulatory Safety Requirements Nokia RoofTop™...
  • Page 105: Hazard Warnings

    • Persons with pacemakers should not go close to the router on the roof. If you have any reason to suspect that interference is taking place with a pacemaker, switch off the router immediately. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 106: Regulatory Safety Requirements

    Regulatory safety requirements 2.3 Regulatory safety requirements • RF exposure - When the Network/Power Unit is plugged in, do not go closer than 7 inches (17 cm) of the antenna on the roof Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 107 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 108: Planning The Installation

    The Nokia roofTop Wireless Router The Multiwire connection (between the router and the Network/ Power Unit) The Network/ Power Unit The grounding (where required) The indoor connections between the Network/Power Unit and the computer(s) in the property. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 109: To Find A Location For The Router

    It is acceptable to use the TV antenna pole already installed. If the TV antenna is used, be sure to loosen the antenna mounting, slide the TV antenna down the pole leaving sufficient room to mount the router at the top of the pole. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 110: To Plan The Network/Power Unit Location

    Test the existing grounding system at the property. Where the existing grounding is not acceptable, consider: • Route of the grounding cable from the router, avoiding other pipes, down spouts etc • Location for the grounding rod Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 111 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 112: Outdoor Installation

    Router mounting hardware • A shielded multiwire cable containing 7 twisted pairs of wires. This is used to connect the wireless router with the NPU. Nokia provides several different lengths of cable with D-Connectors already installed on the end of the cable.
  • Page 113: To Install The Router

    4.2 To install the router Mount the wireless router bracket to the mounting point, ensuring that the bracket is fixed securely. Router bracket fixed to mast Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 114 Attach the antenna by screwing it into the top of the wireless router. Carefully guide the antenna down onto the RF pin to prevent the pin being bent out of shape. Ensure secure connection, but do not overtighten. Attach the omni-directional antenna Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 115 Attach mounting bracket to back of router. Ensure that the bolt fits correctly and is not cross threaded. There is no need to tighten the bolt, play is required to attach the router to the mast mounting bracket. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 116 To install the router Attach mounting bracket to router Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 117 Attach the front panel of the wireless router. Attach front panel of wireless router Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 118 Be careful not to overtighten the bolt. Overtightening of the bolt will strip the thread in the back of the aluminum casting of the wireless router. Slide the router mount onto the mast bracket Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 119: To Prepare And Install Grounding

    Locate the lightning arrestor close to the point of entry to the home. Provide a good, very low resistance wire connection from the wireless router to the ground. Use #12 copper wire connected to the router grounding clamp and a ground rod next to the building. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 120 To install the router Grounding of router and NPU Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 121 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 122: Routing The Cable Into The Property

    18 to 24 inch intervals and are not unsightly. Make sure that there is a “drip loop” at the point of entry to prevent water ingress into the property. Seal any drilled holes using silicone sealant. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 123 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 124: Indoor Installation

    Indoor installation CHAPTER 6 6.1 Introduction 6.1.1 Components to be installed The Indoor portion of the Nokia Wireless Router System consists of: • Network Power Unit (NPU) • Ethernet or home PNA connection cable Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 125: Network/ Power Unit (Npu)

    HomePNA 2.0 interface, a standard phone jack (RJ-11) Ethernet interface, a standard 10/100 BaseT Ethernet jack (RJ-45) Router outdoor unit connection: A multiwire cable from Router unit is connected to this. The connector is a punch down connector inside the unit. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 126: To Install The Network/ Power Unit

    Replace the Network/Power Unit cover and replace the screws. Do not overtighten the screws. Plug the Network/Power Unit into the wall AC outlet. The LEDs on the unit should flash three times to indicate that the unit is connected to the router. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 127 Power on, but no ethernet packets seen Slow Flash Waiting for the router to complete boot cycle Intermittent Flash Off during packet transmit or receive. Otherwise ON No power or the router is not functioning (IROS is off) Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 128 Head and the AirHead is less than, or equal to 3 Hops Fast Flash The unit has 1 neighbor with a 2 Mbps path to the AirHead and the AirHead is less than, or equal to 3 Hops None of the above Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 129: Connection Options

    All these options are described in more detail below. 6.3.2 Network Use a standard Ethernet Cable with an RJ45 connector at the Wireless Router and the appropriate connector at the LAN Ethernet connection. Network Connection Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 130: Direct Personal Computer Connection

    PC. Direct PC connection Changing the Ethernet configuration from a LAN connection to a NOTE: direct PC connection requires changing from a standard Ethernet cable to a crossover cable. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 131: Home Pna Connection

    6.3.4 Home PNA connection • Connect the phone cable between a Network/ Power Unit HomePNA connection and RJ11 phone jack or directly to the PC- HomePNA adapter. • Connect PC to adapter according to manufacturers instructions. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 132: Configuring The End User Pc

    CHAPTER 7 7.1 Introduction After the router installation is complete, your PC needs to be configured for use with the Nokia Wireless Router system. The ISP provides all the information required prior to installation. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 133: To Configure The Your Personal Computer

    "Obtain IP Address Automatically" or enter the IP Address and Subnet Mask in accordance with information provided by the ISP. 3. In the Default Gateway field, enter the IP address of the default gateway, provided by the ISP. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 134: Post Installation Testing

    2. Turn on your PC. Wait for 3-5 minutes to allow the router to anchor to the network. Check that the LEDs indicate an active internet connection (according to Chapter 6 - Indoor installation). Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 135 5. Check the data speed by placing a “throughput test” to www.2wire.com. Generally, speeds of 200kb are acceptable. 6. Where there are problems with download or speed of connection, check the installation first. If this does not solve the problem, then contact the ISP. Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 136 The wiring for an Ethernet Crossover cable for 10Base-T is as follows: RJ45 Plug Pin 1 (Tx+) to Pin 3 (Rx+) Pin 2 (Tx-) to Pin 6 (Rx-) Pin 3 (Rx+) to Pin 1 (Tx+) Pin 6 (Rx-) to Pin 2 (Tx-) Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 137 Nokia RoofTop™ Wireless Router Installation Guide...
  • Page 138: Technical Specifications

    Technical Specifications APPENDIX B This appendix describes technical specifications for Nokia RoofTop™ Wireless Router Models R240 & 240A Outdoor-Mounted Unit. Data Capacity per Cell 12 Mbps (6x2 Mbps per channel) AirHeads per Cell Up to 6 Routers per Cell Up to 240...
  • Page 139 Antenna (8dBi) "H x " Diameter Power Consumption 16 Watts @ 120 VAC Management Nokia Wireless Router Manager, SNMP MIB II, Telnet Internet Protocols IP, TCP, UDP, ICMP, RIPv1, RIPv2, SNMP, TFTP, IGMP, ARP, Proxy-ARP, Telnet, DHCP Relay, DHCP Server, NAT.

This manual is also suitable for:

Rooftop r240a

Table of Contents