Related Manuals for Sony WRT-8P
Summary of Contents for Sony WRT-8P
- Page 1 2-693-883-02(1) UHF Synthesized Transmitter DRAFT version Operating Instructions U3032/U4244 WRT-8P ©2006 Sony Corporation...
- Page 2 RF exposures have not found any below. Refer to these numbers whenever biological effects. Some studies have you call upon your Sony dealer regarding suggested that some biological effects this product. might occur, but such findings have not been confirmed by additional research.
-
Page 3: Table Of Contents
Table of Contents Overview ..................4 Precautions ................4 Parts Identification ..............5 Power Supply ................7 Inserting the battery ............8 Settings ..................9 Entering setting mode ............9 Setting the transmission channel ........9 Resetting the accumulated battery use time indication ...10 Setting the RF output power level ........10 Setting the audio input level ...........11 Setting the +48 V power supply ........11 Attachment and Insertion Procedures ........12... -
Page 4: Overview
Overview Precautions The WRT-8P is a plug-on transmitter for a • The unit is designed for use in ambient UHF synthesized wireless microphone temperature range of 0°C to 50°C (32°F system to be used for broadcast or movie to 122°F). -
Page 5: Parts Identification
Parts Identification 1 Audio input connector 2 AF/PEAK indicator 3 +48V indicator 4 Display section 5 SET button 6 +/– buttons 7 POWER switch 8 LEVEL control 9 INPUT selector 0 Battery lid a Audio input connector Caution Connects a microphone with an XLR-3- When connecting a microphone or a cable 12C type output connector or an audio cable to the unit, be sure to turn the unit off. -
Page 6: Power Switch
b AF/PEAK (audio input/peak level) Transmission indicator channnel Lights up green or red to indicate the strength of the audio input signal level. Transmission Press frequency c +48V indicator Lights up when the INPUT selector is set to MIC position and the +48 V power supply Accumulated button. -
Page 7: Power Supply
MIC: Select when a microphone is connected. LINE: Select when an audio mixer, etc. is The WRT-8P can be powered by one connected to the audio input 6LR61 (9 V) alkaline battery for about 1.5 connector. -
Page 8: Inserting The Battery
Leakage left in the compartment and the unit may cause poor battery contact. If there seems to be poor battery contact, consult your Sony dealer. Inserting the battery Slide the battery lid to release the lock (1), and open the battery compartment (2). -
Page 9: Settings
Channel/frequency indications show again. those of the U66 model. • The channel numbers and frequencies of your transmitter are shown on the “Sony Wireless Microphone System Frequency Setting the transmission List” supplied with this Operating channel Instructions. -
Page 10: Resetting The Accumulated Battery Use Time Indication
Pressing the + button cycles the Press the – button. indications in the order shown in the The time indication resets to “00:00.” tables in the pdf files “Sony Wireless While “00:00” is still displayed, Microphone System Frequency List” previous value can be resumed by supplied with this Operating pressing the + button. -
Page 11: Setting The Audio Input Level
enters transmit mode with the selected RF Occasional lighting of the AF/PEAK output power level. indicator in red is acceptable. Setting the audio input Setting the +48 V power level supply You can adjust the audio input level, You can set the +48 V power supply for the regardless of the INPUT selector position. -
Page 12: Attachment And Insertion Procedures
Note Attachment and +48 V power supply setting can be performed when the INPUT selector is set Insertion to either LINE or MIC. However, +48 V Procedures power supply takes place when next time the transmitter is turned on and the INPUT selector is set to MIC. -
Page 13: Inserting Into The Supplied Soft Case
Detaching a microphone or a Notes on cable Turn the connector ring clockwise to loosen Microphone the latch, then pull out the microphone or System cable connector. Operations • To operate with two or more channels, maintain a distance of at least 30 cm (one ft.) between each pair of transmitters. -
Page 14: System Configuration
The illustration below shows the typical system configuration. F-112 Dynamic Microphone ECM-674/678 Electret Condenser Microphone DMX-P01 Digital Portable Mixer XLR type audio cable (not supplied) WRT-8P WRR-855B/861B/862B UHF Synthesized Output cable Diversity Tuner (supplied with the WRR- 861B/862B) WRR-861B/862B UHF PDW-510/510P/530/ DMX-P01 Digital Synthesized Diversity 530P XDCAM... -
Page 15: Error Messages
When a problem occurs, one of the following error messages may appear on the display. Messages Meanings Remedy ERROR 11 An error has occurred in the Contact your Sony dealer. backup memory data. ERROR 21 The PLL synthesized circuit Turn off the unit and turn it is abnormal. -
Page 16: Specifications
Specifications Power requirements 9.0 V DC (one 6LR61 alkaline battery) Transmitter and modulator Battery life (at 25°C (77°F ) with a Sony section 6LR61 alkaline battery) Approx. 1.5 hours (250 mW, +48 V Oscillator Approx. 2.5 hours (50 mW, +48 V... -
Page 17: Supplied Accessories
44 × 106 × 44 mm (1 × 4 × inches) (w/h/d) Mass Approx. 230 g (8 oz) (including battery) Supplied accessories Operating Instructions (1) Sony Wireless Microphone System Frequency List (1) Soft case (1) Design and specifications are subject to change without notice. Specifications... - Page 18 Sony Corporation Printed in Japan...
Need help?
Do you have a question about the WRT-8P and is the answer not in the manual?
Questions and answers