Related Manuals for Sony WRT-8P
Summary of Contents for Sony WRT-8P
- Page 1 DRAFT UHF Synthesized Transmitter Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. WRT-8P ©2006 Sony Corporation...
- Page 2 The model number plate is located on the side and the serial number is located inside the battery compartment. Record the model and serial numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.
- Page 3 Notice for customers in Canada: Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123. A license is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the license is issued on no- interference, no-protection basis with respect to broadcast signals.
-
Page 4: Table Of Contents
Table of Contents • Overview (Features) ---- 5 • Precautions ---- 5 • Parts Identifications ---- 6 • Power Supply ---- 9 • Settings ---- 10 Initialing setting mode Setting the transmission channel Setting the attenuation level of the audio input Setting the RF output power Setting the +48V power supply •... -
Page 5: Overview (Features)
Overview Precautions The WRT-8P is a plug-on transmitter • The unit is designed for use in for a UHF synthesized wireless ambient temperature range of microphone system to be used for 0°C to 50°C (32°F to broadcast or movie production purpose. -
Page 6: Parts Identifications
Parts Identification Audio input connector AF/PEAK indicator (Audio input LEVEL) +48V indicator Display section SET button - , + buttons POWER switch AF LEVEL control MIC / LINE selector Battery lid... - Page 7 Display section Audio input connector Connect the following Sony’s microphones: F112, ECM-678, ECM- 674 or a line output cable from Sony’s portable mixer DMX-P01. Caution When connecting a microphone or a cable to the unit, be sure to turn the unit off.
- Page 8 Parts identification AF LEVEL control Adjusts the audio input level from the audio input connector . MIC/LINE select switch Set this switch to MIC when a microphone is connected to the audio input connector; set it to LINE when an audio mixer, etc. is connected to the audio input connector.
-
Page 9: Power Supply
Power Supply WRT-8P can be powered by one 6LR61 (9V) alkaline battery for about five hours of continuous operation (at 25°C, 77° F) . The battery condition Indication are given below: Battery indication When you turn the power on, the battery condition is shown by the BATT indication in the display section. -
Page 10: Settings
MIC or LINE in Setting mode. Wait for a few seconds before turning the power on again. • The channel numbers and frequencies of your transmitter are shown on the “Sony Wireless Microphone System Frequency List” supplied with the manual. - Page 11 Pressing the + button cycles the indication in the order shown in the 3 Press the + or – button to select the tables in the “Sony Wireless setting: H (250mW) or L (50 mW). Microphone System Frequency List” supplied with the manual. Pressing the –...
-
Page 12: Setting The +48V Power Supply
Settings Adjusting the Audio Input Setting the +48V power supply Level You can change the audio input level in You can set the +48V power supply for a range of -60 dBV to –40 dBV (when the electric condenser microphone in the MIC/LINE selector is at MIC Setting mode. -
Page 13: Attachment And Installation Procedures
Inserting into the supplied a cable soft case 1 Turn the connector ring left. Insert the WRT-8P into the supplied soft case with the rear side up, and close the flap. 2 Insert to the connector of a microphone or a cable plug until the end. -
Page 14: Notes On Microphone System Operations
Notes on microphone system operations • To operate with two or more • To prevent noise generation, set the channels, maintain a distance of at RF power output to L (50 mW) least 30 cm (one ft.) between each when multiple channels are used pair of transmitters. -
Page 15: System Configurations
System Configurations Example of typical system Microphone F-112 Portable mixer Microphone DMX-P01 ECM-678 ECM-674 Plug-on transmitter WER-8P Portable tuner WRR-855B WRR-861B WRR-862B Portable tuner WRR-861B Portable mixer Camcorder WRR-862B DMX-P01 PDW-530/530P/510/510P... -
Page 16: Error Messages
When a problem occurs, one of the following error message may appear on the display. -
Page 17: Specifications
Power requirements 9.0 V DC (one 6LR61, alkaline battery) Battery life Approx. 2.5 hours at 25°C(77° F ) with Sony 6LR61 alkaline battery (250 mW) Approx. 4 hours at 25°C(77° F ) with Sony 6LR61 alkaline battery (50 mW) General 0 C to 50 °C (32 °... - Page 18 Specifications Dimensions Name plate Design and specifications are subject to change without notice. Unit: mm...
- Page 19 Printed in Japan...