Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Magician LED IEC Power cable (1,5 m) ...
Page 4
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly fastened. • Only operate the device after having familiarized with its functions. • Avoid flames and do not put close to flammable liquids or gases. Ordercode: 43161...
Page 5
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
The Galactic is a Class 3B laser product. Laser Safety and Compliance Information The Galactic is manufactured to comply with the IEC 60825-1 and in accordance with U.S. Food and Drug Administration (FDA) Standards Listed under FDA Document 21 CFR 1040 and subsequent laser notices. Ordercode: 43161...
Page 7
Combo label with the Product Model Number, Serial Number, Date of Manufacturing, Laser Light Warning Label, Warranty Void Label and Interlocked Housing Label Proper Usage Safety and Compliance Information According to FDA Regulations you should operate this product as stated on the left. Ordercode: 43161...
Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE BLACK SILVER NEUTRAL YELLOW/GREEN GREEN GREEN PROTECTIVE GROUND Ordercode: 43161...
After this period, complaints will not be handled anymore. Complaints will only be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting. Ordercode: 43161...
04) 9 x 4W RGB-UV Wash LEDs 05) 3 x Beam LEDs (8 x 0,75W Red, 6 x 0,75W Green, 6 x 0,75W Blue, 8 x 0,75W Amber) 06) IR sensor 07) 12 x 0,5W White 5730 LEDs 08) Laser lens Ordercode: 43161...
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa. Connect the device to the main power supply. The device can be sound-controlled as it is equipped with a built-in microphone. Ordercode: 43161...
Page 13
Be aware that in some countries, there are additional regulations, regarding the use of laser devices. Therefore, we strongly advise you to verify your national laws with your authorities: We do not take any responsibility for eventual discrepancies, changes or adaptions regarding lawful use of laser devices. Fig. 04 Ordercode: 43161...
18 and 19 (Auto, Static color). This means you can set your desired operation mode on the master device and all slave devices will react the same as the master device. Multiple Magicians (Master/Slave control) Fig. 05 Ordercode: 43161...
Do not supply power before the whole system is set up and connected properly. Multiple Magicians DMX Set Up Fig. 06 Note: Link all cables before connecting electric power Ordercode: 43161...
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m). • DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30. The Magician LED can be operated with a controller in control mode or without the controller in stand- alone mode. Ordercode: 43161...
When no button is pressed for 60 seconds, the display will turn off. To light up the display, you have to press the Mode, Enter, Up or Down button. Once you have pressed the button, the display will light up. Ordercode: 43161...
Magician LED Menu Overview The Magician LED will only show its version number at start-up ! Main Menu Options Auto Run Programs Sound-controlled Mode Static Color Mode Slave Mode DMX Channels / DMX Address System Settings Ordercode: 43161...
04) Choose the desired type and press the Enter button again to open the submenu. 05) Press the Up and Down buttons to choose between: mix programs wash programs beam programs laser programs strobe programs 06) Turn on the music and the Magician will immediately start the desired Sound-controlled program. Ordercode: 43161...
04) Once you have chosen the desired DMX configuration press the Enter button to set the DMX address. 05) Press the Up and Down buttons to select the required address. 06) Each DMX configuration has a different maximum number of DMX addresses. Ordercode: 43161...
10) If you have chosen , press the Enter button to reset to default settings. 11) The display will show its version and the device settings have been reset. 12) The device will start up in the Auto Run Programs mode. Ordercode: 43161...
0 = slow, 9 = fast Color settings Press one of the two buttons to choose the desired built-in color of the Wash LEDs Press the button to change the programs Wash /Beam Auto/Sound mode switch /Laser into Auto or Sound mode Ordercode: 43161...
Channel 2 – Built-in programs Laser (CH1 must be set between 106-155 and CH3 between 0-250 for Auto programs (AL) or 251-255 for Sound programs (SL) No function 6-46 AL1/SL1 47-88 AL2/SL2 89-130 AL3/SL3 131-172 AL4/SL4 173-214 AL5/SL5 215-255 AL6/SL6 Ordercode: 43161...
Page 24
No function 6-85 AM1/SM1 86-170 AM2/SM2 171-255 AM3/SM3 Channel 3 – Speed Auto built-in programs/ Sound mode (CH2 must be set between 6-255 0-250 Gradual speed adjustment Auto programs, from slow to fast 251-255 Activate Sound built-in programs Ordercode: 43161...
193-224 AF7/SF7 225-255 AF8/SF8 Channel 5 – Speed Auto built-in programs/ Sound mode (CH1, CH2, CH3 or CH4 must be set between 6-255 0-250 Gradual speed adjustment Auto programs, from slow to fast 251-255 Activate Sound built-in programs Ordercode: 43161...
Strobe flash frequency, from slow to fast (0-20 Hz) 251-255 Sound-activated strobe Channel 7 – Speed Color change / Sound mode Beam LEDs (CH6 must be set between 215-255 0-250 Gradual speed adjustment Color change programs, from slow to fast 251-255 Activate Sound Color change programs Ordercode: 43161...
Channel 2 – Green Dimmer intensity Wash LED 1 (CH5 must be set between 1-100 0-255 Gradual adjustment Green from 0 – 100% Channel 3 – Blue Dimmer intensity Wash LED 1 (CH5 must be set between 1-100 0-255 Gradual adjustment Blue from 0 – 100% Ordercode: 43161...
Page 28
Channel 8 – Blue Dimmer intensity Wash LED 2 (CH10 must be set between 1-100 0-255 Gradual adjustment Blue from 0 – 100% Channel 9 – UV Dimmer intensity Wash LED 2 (CH10 must be set between 1-100 0-255 Gradual adjustment UV from 0 – 100% Ordercode: 43161...
Page 29
Channel 15 – Master Dimmer intensity/Strobe Wash LED 3 (CH11, CH12, CH13 or CH14 must be set between 1-255 0-100 Dimmer intensity, from dark to brightest 101-250 Strobe flash frequency, from slow to fast (0-20 Hz) 251-255 Sound-activated strobe Ordercode: 43161...
Page 30
Amber 61-74 Red+Green 75-88 Red+Blue 89-102 Red+Amber 103-116 Green+Blue 117-130 Green+Amber 131-144 Blue+Amber 145-158 Red+Green+Blue 159-172 Red+Green+Amber 173-186 Red+Blue+Amber 187-200 Green+Blue+Amber 201-214 Red+Green+Blue+Amber 215-228 Color change program 1 229-242 Color change program 2 243-255 Color change program 3 Ordercode: 43161...
Page 31
Red laser on + Green laser flashes 216-255 Red + Green laser flash Channel 23 – Strobe Laser (CH22 must be set between 6-255 No function 6-250 Strobe flash frequency, from slow to fast (0-20 Hz) 251-255 Sound-activated strobe Ordercode: 43161...
Page 32
Channel 27 – Built-in programs Laser (CH26 must be set between 106-155 and CH28 between 0-250 for Auto programs (AL) or 251-255 for Sound programs (SL) No function 6-46 AL1/SL1 47-88 AL2/SL2 89-130 AL3/SL3 131-172 AL4/SL4 173-214 AL5/SL5 215-255 AL6/SL6 Ordercode: 43161...
03) Remove the used fuse. If brown or unclear, it is burned out. 04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the same type and specification. See the product specification label for details. Ordercode: 43161...
02) The laser. Return the Magician to your Showtec dealer. 03) The Wash LEDs, Strobe LEDs and the Beam LEDs. Return the Magician to your Showtec dealer. 04) The fuse. Replace the fuse. See page 32 for replacing the fuse.
Page 35
Turn up the air conditioning • Disconnect the fixture and return it LEDs or Laser damaged to your dealer The power supply settings do not • Disconnect fixture. Check settings match local AC voltage and and correct if necessary frequency Ordercode: 43161...