Table of Contents
Advertisement
Radio Operations
the remote control to seek a higher / lower
station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station
in memory.
1. Press the [SCN/PS/AS] button on the
remote control.
2. When a desired station is tuned in, press
the [SCN/PS/AS] button on the remote
controlagain to continue receiving that
station.
Note:
Be careful not to press and hold the [SCN/
PS/AS] button, otherwise the auto store
function is engaged and the unit starts
storing stations.
Auto store
Only stations with sufficient signal strength
will be detected and stored in the memory.
Press and hold the [SCN/PS/AS] button on
the remote control to start automatic station
Satellite Radio Mode
®
Listeners can subscribe to SIRIUS
Radio on the
Web by visiting www.sirius.com, or by calling (888)
539-SIRIUS. Customers should have their SIRIUS
ID ready (SIRIUS ID is located on the SC-C1
SIRIUS Connect Vehicle Tuner, solid separately).
Customers can listen to music samples by tuning
to channel 184.
Accessing satellite radio mode
Press the [CONTROL] knob or [SRC /
]
button on the remote control to switch to the
SAT source.
search.
To stop auto store, press other buttons
having radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 4 bands, such as FM1, FM2,
FM3 and AM. FM3 and AM can store
by AS function. Each bands can store 6
stations, FZ501 can store 24 stations in
total.
Manual store
When one expected radio station has been
detected, press and hold number button
on the remote control 1-6 to store it in the
memory.
Recall the stored stations
Press one numeric button among 1 to 6 on
the remote control or on the panel to select
the corresponding stored station.
Local seeking
When LOCAL seeking is on, only those
radio stations with strong radio signal could
be received.
Refer to System Setup page 9.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is on.
Displaying the Identification (ID) Code
Before you listen to satellite radio, you must
subscribe to the service using your radio's
identification number. To display the radio
ID, use the [CONTROL] knob (left) or [
]
tuning button on the remote control to tune to
channel "0". The screen displays the radio ID
where the channel name is usually displayed.
Check SC-C1 SIRIUS Connect
Vehicle Tuner
Satellite Radio Mode
If SIRIUS tuner is not connected, "NO
TUNER" will appear on the LCD.
Select a band
Press the the [CONTROL] knob (up long
press) on the panel or [BAND/TOP] button
on the remote control to change between
three SAT bands (SR1, SR2 and SR3). Each
band stores up to six preset stations.
Select a station
Press the [CONTROL] knob (left / right) on
the panel or [
,
] buttons on the remote
control to tune to another station.
Preset mode
Six numbered preset buttons on the remote
control store and recall stations for each
band.
Preset scan
Short press the [SCN/PS/AS] button on the
remote control to start category scanning.
Long press the [SCN/PS/AS] button on
the remote control to start preset station
scanning for 10 seconds each.
Storing a station
1. Select a band (if needed), then select a
station.
2. Press and hold a preset button (numbers
1-6) on the remote control.
3. T h e p r e s e t n u m b e r a n d s t a t i o n i s
displayed and highlighted.
Recalling a station
1. Select a band (if needed).
2. Press a remote control preset button
(numbers 1-6) to select the corresponding
stored station.
Category and Channel search
To access Category and Channel Search
mode, press the [CONTROL] knob (up long
press) on the panel or [BAND/TOP] button
on the remote control long press.
1. Rotate the rotary knob on the panel to
select the desired category.
2. Press the [CONTROL] knob (left / right)
on the panel or [
,
] buttons on
the remote control to select the channel
name.
Direct search
To access Direct Search mode, press the
[CONTROL] knob button on the front panel.
1. Rotate the [CONTROL] knob on the
panel to select the desired direct, and
press the [CONTROL] knob to confirm
the selection.
2. Rotate the [CONTROL] knob on the
panel or press the [
] or [
] button
on the remote control to select the direct
name, and press the knob to confirm the
selection.
PASSWORD
Refer to System Setup page 9.
LOCK
Refer to System Setup page 9.
UNLOCK
Refer to System Setup page 9.
UNSKIP
Refer to System Setup page 9.
FZ502
6
Advertisement
Table of Contents
