LED Par 56 Short Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................6 Claims ....................................6 Description of the device ..............................7 Frontside..................................7 Backside ..................................
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec LED Par 56 Short with 0,5m power cable 1 x color frame ...
Page 4
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
LED Par 56 Short • The user is responsible for correct positioning and operating of the LED Par 56 Short. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. • This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
LED Par 56 Short The LED Par 56 Short can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug.
LED Par 56 Short Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
LED Par 56 Short Description of the device Features The LED Par 56 Short is a LED parcan fixture, with high output and great effects. Compact size Never change lamps again! Sound Control Low power consumption, long lifetime ...
LED Par 56 Short Backside Fig. 02 05) Mode LED (LED will blink in DMX-mode, in other modes it will light up) 06) DMX Dipswitches 07) 3-pin DMX signal connector IN 08) Ground/Earth connection 09) Power cable 10) 3-pin DMX signal connector OUT 11) Audio Sensitivity Installation Remove all packing materials from the LED Par 56 Short.
LED Par 56 Short Color frame retaining clip 01) Press and hold down the color frame retaining clip. 02) Insert the color frame into the bracket. 03) Release the color frame retaining clip in order to secure the color frame in position. Fig.
LED Par 56 Short One LED Par 56 Short (Sound-controlled) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket.
LED Par 56 Short Multiple LED Pars (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) When all dipswitches are turned off, the LED Par is in DMX Mode. 04) Use a 3-pin XLR cable to connect the LED Pars and other devices.
Page 13
Addresses on the controller are set by flipping the appropriate DMX dipswitches. You need to know that DMX address settings are the sum of the dip switch values. A standard DMX address for a Showtec LED Par 56, which has 6 channels is as follow:...
LED Par 56 Short Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
LED Par 56 Short DMX Channels 6 channels Channel 1 – Red 0-255 Gradual adjustment Red, from 0-100% Channel 2 – Green 0-255 Gradual adjustment Green, from 0-100% Channel 3 – Blue 0-255 Gradual adjustment Blue, from 0-100% Channel 4 – Macro colors No function 8-255 Gradual adjustment colors, from 0-100%...
01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the LED Par to your Showtec dealer. 03) The internal fuse. Return the LED Par to your Showtec dealer. 04) If all of the above appears to be O.K., plug the unit in again.
Page 18
Check if power is switched on and One or more cables are plugged in fixtures do not function at all Internal fuse blown • Return the Par 56 to your Showtec dealer Fixtures reset The controller is not connected. • Connect controller. correctly, but all 3-pin XLR Out of the controller •...
LED Par 56 Short Product Specifications Model: Showtec LED Par 56 Short Input Voltage: 240V-50Hz (CE) Power consumption: DMX linking: 30pcs Dimensions: 210 x 200 x 260 mm (LxWxH) Weight: 0,78 kg Operating and Programming: Signal pin OUT: Pin 1 (earth), pin 2 (-), pin 3 (+)