IPC Eagle 1050 Operation Manual
  1. Manuals
  2. Brands
  3. IPC Eagle Manuals
  4. Floor Machine
  5. 1050
  6. Operation manual

IPC Eagle 1050 Operation Manual

Hide thumbs

Advertisement

Table of Contents

OPERATIONS
MANUAL
1050

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1050 and is the answer not in the manual?

Questions and answers

Related Manuals for IPC Eagle 1050

Summary of Contents for IPC Eagle 1050

  • Page 1 OPERATIONS MANUAL 1050...

  • Page 2: Introduction / General Warnings

    English (Translation of original instructions) English (Translation of original instructions) is not your case, contact an authorised service centre. INTRODUCTION / GENERAL WARNINGS · Always use ORIGINAL spare parts. You can purchase these from a dealer or authorised retailer. Welcome on board! Disconnect the machine from the mains before carrying out any We thank you for choosing IPC and congratulate you for purchasing maintenance operation.

  • Page 3: Preparing The Machine

    English (Translation of original instructions) UNPACKING Unpack your machine with great care, avoiding any manoeuvre that could lead to damage. Once you have unpacked it, make sure all parts are in a good condition. If you notice any damage, DO NOT use the machine and contact your retailer immediately.
  • Page 4 English (Translation of original instructions) English (Translation of original instructions)  - If the batteries are already filled: 3- If the machine has been supplied without batteries, these must be purchased and installed accordingly. a) Check the level of electrolyte and top up if necessary (use only Competent battery specialists should preferably be contacted to distilled water).

  • Page 5: Removing The Batteries

    English (Translation of original instructions) REMOVING THE BATTERIES When removing the batteries, the operator must be equipped with suitable personal protection devices (gloves, goggles, overalls, safety shoes, etc) to reduce the risk of accidents. Make sure the switches on the control panel are in the “0” position (off) and the machine is turned off.
  • Page 6 English (Translation of original instructions) English (Translation of original instructions) BUTTON  (Light cleaning, indoors, concrete, quartz, smooth floors, FURTHER PERFORMANCES OF THE MACHINE FEATURING AN etc.) ENGINE BUTTON 2 (Medium cleaning, carpet or other surfaces) The version featuring an engine can guarantee the same working BUTTON 3 (Heavy duty cleaning, outdoors, asphalt or rough surfaces efficiency even when the motor is off, for instance when the fuel has with rubble, etc.).

  • Page 7: Emptying The Waste Bin

    English (Translation of original instructions) intervals. EMPTYING THE WASTE BIN 2) by means of an electric filter shaker that is manually started Just a simple command is needed to keep the filter in perfect working order: press the button marked ‘F’ and hold it down for a few seconds.

  • Page 8: Replacing The Centre Brush

    English (Translation of original instructions) English (Translation of original instructions) REPLACING THE CENTRE BRUSH Caution: this operation must be carried out with the machine off and the key removed. Remove the worn brush. This machine features a system for automatically adjusting the pressure exerted and compensating for wear.

  • Page 9: Adjusting The Brake

    English (Translation of original instructions) Refit the cover of the brush compartment and tighten the knobs by following the disassembly instructions in reverse order. · The battery must be recharged in a sufficiently ventilated area · Open up all the caps of the battery cells. ·...

  • Page 10: Engine Maintenance

    English (Translation of original instructions) English (Translation of original instructions) AIR FILTER OF THE ENGINE ENGINE MAINTENANCE Check the state of the engine’s air filter regularly. Take into account that it is necessary to carefully read the use and If necessary, wash the sponge (pre-filter) with water and soap or a maintenance handbook of the engine.

  • Page 11: Summary Table

    English (Translation of original instructions) SUMMARY TABLE MAINTENANCE OF THE BATTERY VERSION IMPORTANT: these operations must be carried out with the machine off and the key removed. All routine and corrective maintenance operations must be effected by competent personnel or at an authorised service centre. NOTE: the life of the battery strictly relates to regular periodic maintenance (checking the level and density of the electrolyte).
  • Page 12 English (Translation of original instructions) SUMMARY TABLE MAINTENANCE OF THE DUAL POW ER - PETROL VERSION IMPORTANT: these operations must be carried out with the machine off and the key removed. All routine and corrective maintenance operations must be effected by competent personnel or at an authorised service centre. As far as maintenance work on the engine is concerned, refer to the relevant handbook.

  • Page 13: Troubleshooting Table

    English (Translation of original instructions) TROUBLESHOOTING TABLE POSSIBLE INTERVENTION ERROR DESCRIPTION MACHINE BEHAVIOUR SECURITY CODE HAVING GONE UP A STEEP SLOPE, THIS MAY BE NORMAL. LEAVE THE ENGINE TO TRACTION ENGINE OVERHEATS TO 95°C OR MOTOR PAUSE THE TRACTION IS BLOCKED COOL DOWN FOR 20 MINUTES.

  • Page 14: Led Codes

    English (Translation of original instructions) Drive board alarms If the machine drive is interrupted, the error code should be identified by means of the status LED. In the absence of malfunctions, the status LED is steadily on while the machine is in operation. If a malfunction is detected, the status LED provides two types of information, a slow flash (2 Hz) or a rapid flash (4 Hz) to indicate the severity of the malfunction.

Table of Contents