Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec T510
Summary of Contents for Trotec T510
- Page 1 T510 OPERATING MANUAL MATERIAL MOISTURE MEASURING DEVICE...
-
Page 2: Table Of Contents
Further, ® TROTEC accepts no liability whatsoever for possible mistakes or damage which have been caused by utilising the determined ® measured results. © TROTEC Operating manual – Material moisture measuring device T510... -
Page 3: Information About The Device
Cross control Information about the device Description of the device The material moisture measuring device T510 enables the deter- mination of the moisture content in wood and other soft building materials (e.g. gypsum, plaster) according to the resistance measurement method. -
Page 4: Technical Data
0.1 M% Intended use Operating temperature 0 °C to +50 °C with Only use the material moisture measuring device T510 to < 90 % or < 20 g/m (non-condensing) measure the moisture content of wood and other soft building Storage temperature -20 °C to +60 °C with... -
Page 5: Transport And Storage
• When storing the device for a long time, remove the batteries. Accessories Optionally, the following accessories are available for transport and storage: ® • TROTEC Holster 3 ® For further information please contact your TROTEC customer Operating manual – Material moisture measuring device T510... - Page 6 Wait a few minutes until the device has become adjusted to the changed conditions before carrying out a measurement. Operating manual – Material moisture measuring device T510...
- Page 7 – Lower measurement value display: preset material tem- perature in °C or °F. • Building moisture: – Upper measurement value display: no indication. – Lower measurement value display: measured material moisture in digits. Operating manual – Material moisture measuring device T510...
- Page 8 6. Press the OK button (10) for approx. 2 seconds. – With activated alarm function the indication ALARM (18) – The wood temperature is set. continues to be displayed. – The device switches to measuring mode. Operating manual – Material moisture measuring device T510...
- Page 9 1. Press the Up key (7) to switch between °C and °F. – The temperature will be displayed in the selected unit. – The unit (15) will be indicated on the display (1). Operating manual – Material moisture measuring device T510...
-
Page 10: Measuring Principle
– Observe the condition of the external electrodes and pre- pare these for the measurement, if required. – For further information on suitable electrodes please ® contact the TROTEC customer service. Operating manual – Material moisture measuring device T510... - Page 11 The conductivity transverse to the wood fibre direction is low- basis by means of the Darr test. er than that in line with it. Depending on the type of wood it varies by the factor 2.3 to 8. Operating manual – Material moisture measuring device T510...
- Page 12 Especially in case of insulation materials with metal lamination, measured values are often misinterpreted during the resistance measurement. Operating manual – Material moisture measuring device T510...
- Page 13 – no drying required threshold – drying may be required after evaluation of the damage characteristics thorough moisture penetration – drying by use of technical means required All values are approximations and without warranty. Operating manual – Material moisture measuring device T510...
-
Page 14: Table Of Wood Types
American 1. Download the current PC software from the Internet. To do cocus wood (granadillo) so, visit the website www.trotec.de. First click on Service, bamboo dark, melamine-faced chipboard doussie (Afzelia) followed by Downloads and then Software. Select the iroko (African teak);... -
Page 15: Errors And Faults
• Check that the batteries are properly positioned. Check the such as pliers when doing so. polarity is correct. • Never carry out an electrical check yourself; instead, contact ® your TROTEC customer service. Operating manual – Material moisture measuring device T510... -
Page 16: Disposal
Directive compatibility. 2002/96/EC of the European Parliament and Council of Herewith, we declare that the T510 material moisture measuring 27th January 2003 concerning old electrical and electronic device was developed, constructed and produced in compliance equipment. After the end of its use, please dispose of this device with the named EC directives.