Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the operating manual must be observed. multifunction measuring meter T3000...
Page 3
– excessively dry or damp materials • leak detection with trace gas To use the device for its intended use, only use accessories and spare parts which have been approved by Trotec. Improper use Do not use the device in potentially explosive atmospheres, when whet or for measurements in liquids.
USB connection cable. Then you can extract and analyse your Battery compartment with cover measured results with the optional MultiMeasure Studio "Power" button Standard or MultiMeasure Studio Professional software. Contact your Trotec customer service. USB port multifunction measuring meter T3000...
Page 5
Ambient temperature Operation 0 °C to +50 °C 10 °C to +60 °C Storage -20 °C to +50 °C -20 °C to +50 °C Relative humidity < 95 % (non-condensing) < 95 % (non-condensing) * Data changes reserved. multifunction measuring meter T3000...
Transport To safely transport the multifunction measuring meter and accessories, use the optional MultiMeasure transport case (12) recommended by Trotec. Otherwise, protect the device during use and transport with an optional device bag (13). Contact your Trotec customer service. 1. Remove the cover of the battery compartment (9).
Page 7
"OK" key (5). For safety reasons, some options can only be selected and configured by using the cross control and the "OK" key (5) (e.g. date and time in the Settings screen). multifunction measuring meter T3000...
Page 8
(with SDI sensor) Hydrogen measure hydrogen content (trace gas; with SDI sensor) "Measuring mode – Wood moisture" screen Submenu Function Measuring mode Carrying out measurements Archive open archived measured values Settings make any device settings multifunction measuring meter T3000...
Page 9
3. Press the "OK" button (5) or the button (34) to measurement). confirm the selected grid measuring spot. => The dimensionless measured value is recorded. 4. Use the keys of the cross control to select the next grid measuring spot and repeat the process. multifunction measuring meter T3000...
Page 10
PC software after grid measurement. Specifies the temperature value (FIX) for the temperature compensation which is necessary for accurate wood moisture calculation if the integrated sensor is not being used. Saves the settings. multifunction measuring meter T3000...
Page 11
BNC electrode): M%: indicates the measured value as a mass percentage (with SDI sensor TS 660 SDI only) CM%: indicates the measured value according to the calcium carbide method Resets the measured values shown in item 53 to zero. multifunction measuring meter T3000...
Page 12
Skips to the start of the next column. Info Saves the measured values in the archive. The settings saved here are also used for all following measurements, unless they are deactivated (in the corresponding menu item)! multifunction measuring meter T3000...
Page 13
(edge lengths) as well as the form of the object to be measured (e.g. pipe or shaft) for the volumetric flow measurement (see section Measuring mode flowrate – Measuring range). Saves the measured values in the archive. multifunction measuring meter T3000...
Page 14
Press this key or key 89 again to continue recording. move on to the next field. Saves the settings. Info The settings saved here are also used for all following measurements, unless they are deactivated (in the corresponding menu item)! multifunction measuring meter T3000...
Page 15
100 Shows the measured values according to the specifications in item 98. 101 Opens the menu for setting a fixed recording duration for an automatic measurement (see section Measuring mode humidity – Automatic measurement). 102 Saves the measured values in the archive. multifunction measuring meter T3000...
Page 16
112 Shows the measured values according to the specifications in item 110. 113 Opens the menu for setting a fixed recording duration for an automatic measurement (see section Measuring mode temperature – Automatic measurement). 114 Saves the measured values in the archive. multifunction measuring meter T3000...
Page 17
So, only use the Measuring mode – Hydrogen for locating leaks. 126 Deletes all entries from the archive. Then, a safety prompt opens. Confirm it by pressing the "OK" key if you want to delete all entries. Otherwise, touch the "Cancel" key. multifunction measuring meter T3000...
Page 18
Confirm it by pressing the "OK" key (5) if you ð The row is deselected. want to delete the entry. Otherwise, touch the "Cancel" 134 Opens the next screen. key. 129 Closes this screen and returns to the list view of the archive entries. multifunction measuring meter T3000...
Page 19
100 % RH, where condensation actually occurs! Knowing the critical dew point is particularly important when carrying out measurements e.g. behind picture frames, closets or wardrobes in environments with otherwise inconspicuous room climate values. multifunction measuring meter T3000...
Page 20
NTC sensor. The set offset value will be accordingly saved in the device, not in the sensor. This means that all connected sensors of the same type also work with this adjusted offset! multifunction measuring meter T3000...
Page 21
1. Switch off the device by pressing the "Power" button (see section "Switching the device off"). 2. Detach connecting cables and sensors. 3. Clean the device according to the "Maintenance" chapter. 4. Store the device according to the "Storage" chapter. multifunction measuring meter T3000...
You can only use all configuration, visualisation and functional options of ® the device when using this PC software and a TROTEC dongle (professional). Installation requirements Ensure that the following minimum requirements for installing...
For maintenance or repair work which requires the The device runs but no measured values are shown: housing to be opened, contact the Trotec customer • Check whether the multifunction measuring meter is in the service. Devices which have been opened correct sensor mode.
If the lead battery is discharged, a three-beep signal sounds Due to its high resolution accuracy, the trace gas sensor every 10 seconds. The colour display of the T3000 multifunction TS 800 SDI already detects low concentrations of hydrogen from measuring meter displays the flashing value "-1000.0" (battery 1 ppm.
Page 25
151 Connection for charger Preparing for measurement with trace gas sensor (heating phase) 1. Ensure that the trace gas sensor and the T3000 multifunction measuring meter are properly connected to each other. 2. Ensure that the T3000 multifunction measuring meter is switched on.
Page 26
During heating, the "Hydrogen 2" value on the colour display or display shows two different measured values in the the T3000 multifunction measuring meter drops from 50 to 0. "Measuring mode – hydrogen" screen at the same time. Upon reaching zero, the trace gas sensor is ready for operation.
Page 27
Because both the base value and the reference value were It is thus possible to locate very high H2 concentrations in specified in this environment, both measured value displays surroundings already enriched with trace gas. show the value 0 in this environment. multifunction measuring meter T3000...
Do not use this trace gas to calibrate the trace gas sensor. The • Due to the physical principle of the detection process, the calibration gas must contain oxygen. Trotec recommends trace gas sensor does not only react to hydrogen, but also 50 ppm of hydrogen in synthetic air as calibration gas.
Page 29
TS 810 SD I Preparing for measurement with trace gas sensor (heating phase) 1. Ensure that the trace gas sensor and the T3000 multifunction measuring meter are properly connected to each other. 2. Ensure that the T3000 multifunction measuring meter is Item Operating element switched on.
Page 30
During heating, the "Hydrogen 2" value on the colour display of For the differentiated indication measurement, the trace gas the T3000 multifunction measuring meter drops from approx. sensor also reacts to minimal changes in the hydrogen -50 to 0 (countdown). The duration of the heating phase...
Page 31
• Use the differentiated indication measurement to bypass existing, permanent sources of interference on a case by case basis (see chapter "Differentiated indication measurement"). This lowers the sensitivity to sources of interference and raises the sensitivity for detecting hydrogen. multifunction measuring meter T3000...
SDI H2 sensor of recovery of waste equipment as well as to prevent negative Display protection film for T3000 / T210 / 3.510.200.220 effects for the environment and human health caused by the...