Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec TD200
Summary of Contents for Trotec TD200
- Page 1 TD200 OPERATING MANUAL LASER DISTANCE MEASURING DEVICE...
-
Page 2: Table Of Contents
Keep all safety signs, stickers and labels in legible operating manual must be observed. condition. • Do not open the device. • Avoid looking directly into the laser beam. • Never point the laser beam at people or animals. laser distance measuring device TD200... - Page 3 To use the device for its intended use, only use accessories and Examining the laser output aperture by use of optical spare parts which have been approved by Trotec. instruments (e.g. magnifying glass, magnifiers and the like) entails the risk of eye damage.
-
Page 4: Information About The Device
(e.g. water), dust-free glass, styrofoam or other semi-permeable materials. The measurement result may also be falsified if the laser encounters a high-gloss surface and is deflected by it. Non-glossy, non-reflective or dark surfaces can extend the measurement duration. laser distance measuring device TD200... - Page 5 Press for a long time: opens the memory mode Press briefly: opens the measuring menu when in memory mode: changes between data values and photos when in settings menu: changes the submenu Press and hold: time-delayed measurement (5 s) laser distance measuring device TD200...
-
Page 6: Transport And Storage
5 V, 1 A/5 A Scope of delivery • 1 x Device TD200 • 3 x rechargeable batteries 1.2 V AAA • 1 x Wrist strap • 1 x Bag/holster • 1 x USB cable • 1 x screwdriver • 1 x Quick guide laser distance measuring device TD200... -
Page 7: Operation
ð The selected option is adopted and displayed in the menu item on the right. 4. Press the button (15) to exit the settings menu and return to the measuring menu. laser distance measuring device TD200... - Page 8 Measuring partial heights over three points (Pythagoras 2, 3-point) Measuring heights over three points (Pythagoras 1, 3-point) Measuring heights over two points (Pythagoras 2-point) By pressing the button (15) you can exit the measuring function and return to the individual measurement mode. laser distance measuring device TD200...
- Page 9 (e.g. in the corner of a room). 3. Briefly press the button to terminate the non-stop measurement. ð The maximum, minimum and last measured value are indicated on the display. laser distance measuring device TD200...
- Page 10 A and B appears. The following buttons are available for entering the values: Button Function navigate to the left navigate to the right increase the value reduce the value save displayed value Exit menu laser distance measuring device TD200...
- Page 11 ð The length of the distance is indicated on the display. ð The device automatically calculates the length (L) and the angle (α) between the diagonal and the baseline of the trapezoidal area and indicates the values on the display. laser distance measuring device TD200...
- Page 12 ð The length of the distance is indicated on the display. indicates this value on the display. ð The device automatically calculates the height (H) and indicates this value on the display. laser distance measuring device TD200...
- Page 13 90 ° angle to the height) and press the button (13) briefly to determine the distance to the lower endpoint. ð The length of the distance is indicated on the display. ð The device automatically calculates the height (H) and indicates this value on the display. laser distance measuring device TD200...
-
Page 14: Maintenance And Repair
1. Press the button (15) for a long time. batteries for a short time for technical reasons, it is ð The display is switched off. mandatory to remove the non-rechargeable batteries from the device before connecting it to a computer or a charger! laser distance measuring device TD200... -
Page 15: Errors And Faults
Range exceeded Observe the range values specified in the Technical data chapter. Hardware fault Repeatedly switch the device on and off. If the indication continues to appear, please contact the Trotec customer service. laser distance measuring device TD200... -
Page 16: Declaration Of Conformity
Applied national standards and technical specifications: Declaration of conformity • Regulation (EC) 1907/2006 We – Trotec GmbH – declare in sole responsibility that the • EN 301 489-1 V2.2.3:2019-11 product designated below was developed, constructed and • EN 301 489-3 V2.1.1 produced in compliance with the requirements of the EU Radio •... - Page 17 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...