Supero 8047R-7JRFT User Manual
  1. Manuals
  2. Brands
  3. Supero Manuals
  4. Server
  5. 8047R-7JRFT
  6. User manual

Supero 8047R-7JRFT User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Проконсультироваться и купить данное оборудование вы можете в компании «АНД-Системс»
адрес: 125480, г.Москва, ул.Туристская, д.33/1; site: https://andpro.ru тел: +7 (495) 545-4870 email: info@andpro.ru
При обращении используйте промокод AND-PDF и получите скидку.
S
®
UPER
S
S
UPER
ERVER
8047R-7JRFT
USER'S MANUAL
Revision 1.0

Advertisement

Table of Contents
loading

Related Manuals for Supero 8047R-7JRFT

Summary of Contents for Supero 8047R-7JRFT

  • Page 1 Проконсультироваться и купить данное оборудование вы можете в компании «АНД-Системс» адрес: 125480, г.Москва, ул.Туристская, д.33/1; site: https://andpro.ru тел: +7 (495) 545-4870 email: info@andpro.ru При обращении используйте промокод AND-PDF и получите скидку. ® UPER UPER ERVER 8047R-7JRFT USER'S MANUAL Revision 1.0...
  • Page 2 The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.

  • Page 3: About This Manual

    About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 8047R-7JRFT. Installation and maintainance should be performed by experienced technicians only. The SuperServer 8047R-7JRFT is a high-end server based on the SC848E16- R1K62B 4U rackmount chassis and the quad processor X9QR7-TF-JBOD serverboard.
  • Page 4 SUPERSERVER 8047R-7JRFT USER'S MANUAL Refer to Chapter 6 for detailed information on the SC848E16-R1K62B server chassis. You should follow the procedures given in this chapter when installing, removing or reconfi guring SATA or peripheral drives and when replacing system power supply units and cooling fans.
  • Page 5 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes...

  • Page 6: Table Of Contents

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Table of Contents Chapter 1 Introduction Overview ......................1-1 Serverboard Features ..................1-2 Processors ...................... 1-2 Memory ......................1-2 Serial ATA ....................... 1-2 SAS ......................... 1-2 PCI Expansion Slots ..................1-3 Onboard Controllers/Ports ................1-3 Graphics Controller ..................1-3 Other Features ....................
  • Page 7 Table of Contents Reliable Ground ..................2-3 Rack Mounting Instructions ................2-4 Identifying the Sections of the Rack Rails ............2-4 Locking Tabs ....................2-5 Releasing the Inner Rail ................. 2-5 Installing The Inner Rails on the Chassis ............2-6 Installing the Outer Rails on the Rack ............
  • Page 8 SUPERSERVER 8047R-7JRFT USER'S MANUAL Connecting the Control Panel ................. 5-4 Processor and Heatsink Installation..............5-5 Installing the LGA2011 Processor ..............5-5 Installing a Passive CPU Heatsink ............... 5-10 Removing the Heatsink ..................5-11 Installing Memory ..................5-12 Installing Memory ..................5-12 Memory Support ....................
  • Page 9 Table of Contents IPMI ....................... 7-28 Boot ....................... 7-30 Security ......................7-31 Save & Exit ....................7-32 Appendix A BIOS Error Beep Codes Appendix B System Specifi cations...
  • Page 10 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes...

  • Page 11: Chapter 1 Introduction

    Chapter 1 Introduction Overview The SuperServer 8047R-7JRFT is a high-end server comprised of two main subsystems: the SC848E16-R1K62B 4U server chassis and the X9QR7-TF-JBOD quad processor serverboard. Please refer to our web site for information on operating systems that have been certifi ed for use with the system (www.supermicro.com).

  • Page 12: Serverboard Features

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Serverboard Features At the heart of the SuperServer 8047R-7JRFT lies the X9QR7-TF-JBOD, a quad processor serverboard based on the Intel® C602 chipset and designed to provide maximum performance, mounted in the SC848E16-R1K62B chassis. The sections below cover the main features of the X9QR7-TF-JBOD serverboard (see Figure 1-1 for a block diagram of the chipset).

  • Page 13: Pci Expansion Slots

    Chapter 1: Introduction PCI Expansion Slots The SuperServer 8047R-7JRFT has seven (7) PCI Express 3.0 x16 slots (CPU1_ Slot1, CPU4_Slots3/4, CPU3_Slots5/6, CPU2_Slots7/8) and one (1) PCI Express 3.0 x8 in x16 slot (CPU1_Slot1) on the X9QR7-TF-JBOD serverboard. Onboard Controllers/Ports Two Fast UART 16550 serial ports and an Intel X540 10G Ethernet Dual-Channel Controller for two TLAN (TLAN 1/TLAN 2) ports are located on the serverboard.

  • Page 14: Sata Subsystem

    Front Control Panel The SC848E16-R1K62B chassis includes a front control panel on the chassis which controls the system. This control panel on the SuperServer 8047R-7JRFT provides you with system monitoring and control. LEDs indicate system power, HDD activity, network activity, system overheat and power supply failure. A main power button and a system reset button are also included.

  • Page 15: Advanced Power Management

    Chapter 1: Introduction Advanced Power Management Intel® Intelligent Power Node Manager (NM) The Intel® Intelligent Power Node Manager (IPNM) provides your system with real-time thermal control and power management for maximum energy effi ciency. Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard Management Controller), your system must also have IPNM-compatible Manageability Engine (ME) fi...

  • Page 16: System Block Diagram

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Figure 1-1. Intel C602 Chipset: System Block Diagram Note: This is a general block diagram and may not exactly repre- sent the features on your serverboard. See the previous pages for the actual specifi cations of your serverboard. This block diagram is intended for your reference only.

  • Page 17: Contacting Supermicro

    Chapter 1: Introduction Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel:...
  • Page 18 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes...

  • Page 19: Chapter 2 Rack Installation

    Chapter 2: Server Installation Chapter 2 Rack Installation Overview This chapter provides a quick setup checklist to get your chassis up and running. Following these steps in the order given should enable you to have the system operational within a minimal amount of time. Unpacking the System You should inspect the box which the chassis was shipped in and note if it was damaged in any way.

  • Page 20: Warnings And Precautions

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Warnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the fl oor with the full weight of the rack resting on them. • In single rack installations, stabilizers should be attached to the rack.

  • Page 21: Rack Mounting Considerations

    Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera- ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient tempera- ture (TMRA).

  • Page 22: Rack Mounting Instructions

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Rack Mounting Instructions This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. You should also refer to the installation instructions that came with the rack unit you are using.

  • Page 23: Locking Tabs

    Chapter 2: Server Installation Locking Tabs Each inner rail has a locking tab. This tab locks the chassis into place when installed and pushed fully into the rack. These tabs also lock the chassis in place when fully extended from the rack. This prevents the server from coming completely out of the rack when when the chassis is pulled out for servicing.

  • Page 24: Installing The Inner Rails On The Chassis

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Inner Rails Figure 2-3. Installing the Inner Rails Installing The Inner Rails on the Chassis Installing the Inner Rails 1. Confi rm that the left and right inner rails have been correctly identifi ed. Place the inner rail fi rmly against the side of the chassis, aligning the hooks on the side of the chassis with the holes in the inner rail.

  • Page 25: Installing The Outer Rails On The Rack

    Chapter 2: Server Installation Figure 2-4. Extending and Releasing the Outer Rails Installing the Outer Rails on the Rack Installing the Outer Rails 1. Press upward on the locking tab at the rear end of the middle rail. 2. Push the middle rail back into the outer rail. 3.
  • Page 26 SUPERSERVER 8047R-7JRFT USER'S MANUAL Figure 2-5. Installing into a Rack Note: fi gures are for illustrative purposes only. Always install servers into racks from the bottom up. Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the fl oor before you slide the unit out for servicing.

  • Page 27: Standard Chassis Installation

    Chapter 2: Server Installation Standard Chassis Installation Installing the Chassis into a Rack 1. Confi rm that the inner rails are properly installed on the chassis. 2. Confi rm that the outer rails are correctly installed on the rack. 3. Pull the middle rail out from the front of the outer rail and make sure that the ball-bearing shuttle is at the front locking position of the middle rail.
  • Page 28 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes 2-10...

  • Page 29: Chapter 3 System Interface

    Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the control panel as well as others on the drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specifi...

  • Page 30: Control Panel Buttons

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Control Panel Buttons There are two push-buttons located on the left handle of the chassis. These are (in order from top to bottom) a power on/off button and a reset button. Power: The main power button is used to apply or remove power from the power supply to the server system.
  • Page 31 Chapter 3: System Interface NIC1: Indicates network activity on GLAN1 when fl ashing. NIC2: Indicates network activity on GLAN2 when fl ashing. Overheat/Fan Fail: When this LED fl ashes, it indicates a fan failure. When continuously on (not fl ashing) it indicates an overheat condition, which may be caused by cables obstructing the airfl...

  • Page 32: Drive Carrier Leds

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Drive Carrier LEDs Your system supports SAS/SATA drives. SAS/SATA Drives Each SAS/SATA drive carrier has two LEDs. • Blue: Solid on = Drive is present and available. Blinking = Drive is actively being accessed. Each Serial ATA drive carrier has a blue LED. When illuminated in a solid on state, this blue LED (on the front of the SAS/SATA drive carrier) indicates drive activity.

  • Page 33: About Standardized Warning Statements

    Chapter 4: Warning Statements for AC Systems Chapter 4 Standardized Warning Statements for AC Systems About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance.
  • Page 34 SUPERSERVER 8047R-7JRFT USER'S MANUAL Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
  • Page 35 Warning Statements for AC Systems ‫ﺟﺴﺪﻳﺔ‬ ‫ﺍﺻﺎﺑﺔ‬ ‫ﺗﺘﺴﺒﺐ ﻓﻲ‬ ‫ﺣﺎﻟﺔ ﻳﻤﻜﻦ ﺃﻥ‬ ‫ﺍﻧﻚ ﻓﻲ‬ ‫ﺧﻄﺮ‬ ‫ﻳﻌﻨﻲ‬ ‫ﻫﺬﺍ ﺍﻟﺮﻣﺰ‬ !‫ﺗﺤﺬﻳﺮ‬ ‫ﺍﻟﺪﻭﺍﺋﺮ‬ ‫ﺑﺎﻟﻤﺨﺎﻁﺮ ﺍﻟﻨﺎﺟﻤﺔ ﻋﻦ‬ ‫ﻦ ﻋﻠﻰ ﻋﻠﻢ‬ ، ‫ﻛ‬ ‫ﻣﻌﺪﺍﺕ‬ ‫ﺗﻌﻤﻞ ﻋﻠﻰ ﺃﻱ‬ ‫ﻗﺒﻞ ﺃﻥ‬ ‫ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬ ‫ﺣﻮﺍﺩﺙ‬ ‫ﺃﻱ‬ ‫ﻭﻗﻮﻉ‬ ‫ﻤﻨﻊ‬ ‫ﻟ‬ ‫ﺍﻟﻮﻗﺎﺋﻴﺔ‬...

  • Page 36: Installation Instructions

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、 設置手順書をお読み下さい。 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

  • Page 37: Circuit Breaker

    Chapter 4: Warning Statements for AC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. サーキッ ト ・ ブレーカー この製品は、 短絡 （過電流） 保護装置がある建物での設置を前提としています。 保護装置の定格が250 V、...

  • Page 38: Power Disconnection Warning

    SUPERSERVER 8047R-7JRFT USER'S MANUAL 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.
  • Page 39 Chapter 4: Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché...

  • Page 40: Equipment Installation

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Equipment Installation Warning! Only trained and qualifi ed personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、 交換、 またはサービスを許可 されています。 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifi...

  • Page 41: Restricted Area

    Chapter 4: Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalifi ceerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

  • Page 42: Battery Handling

    SUPERSERVER 8047R-7JRFT USER'S MANUAL ‫אזור עם גישה מוגבלת‬ !‫אזהרה‬ ‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה. הגישה ניתנת בעזרת‬ .('‫כלי אבטחה בלבד )מפתח, מנעול וכד‬ ‫ﻣﺤﻈﻮﺭﺓ‬ ‫ﻣﻨﺎﻁﻖ‬ ‫ﻟﺘﺮﻛﻴﺒﻬﺎ ﻓﻲ‬ ‫ﻫﺬﻩ ﺍﻟﻮﺣﺪﺓ‬ ‫ﺗﺨﺼﻴﺺ‬ ‫ﺗﻢ‬ ،‫ﺃﺩﺍﺓ ﺧﺎﺻﺔ‬ ‫ﻣﻦ ﺧﻼﻝ ﺍﺳﺘﺨﺪﺍﻡ‬...
  • Page 43 Chapter 4: Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.

  • Page 44: Redundant Power Supplies

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニッ トは複数の電源装置が接続されている場合があります。 ユニッ トの電源を切るためには、 すべての接続を取り外さなければなりません。 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

  • Page 45: Backplane Voltage

    Chapter 4: Warning Statements for AC Systems ‫ﺍﻣﺪﺍﺩ ﺍﻟﻄﺎﻗﺔ‬ ‫ﺑﻮﺣﺪﺍﺕ‬ ‫ﻋﺪﺓ ﺍﺗﺼﺎﻻﺕ‬ ‫ﺠﻬﺎﺯ‬ ‫ﺍﻟ‬ ‫ﻳﻜﻮﻥ ﻟﻬﺬﺍ‬ ‫ﻗﺪ‬ ‫ﺍﻟﻜﻬﺮﺑﺎء‬ ‫ﻋﻦ‬ ‫ﻮﺣﺪﺓ‬ ‫ﺍﻟ‬ ‫ﻟﻌﺰﻝ‬ ‫ﻛﺎﻓﺔ ﺍﻻﺗﺼﺎﻻﺕ‬ ‫ﻳﺠﺐ ﺇﺯﺍﻟﺔ‬ 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을...

  • Page 46: Comply With Local And National Electrical Codes

    SUPERSERVER 8047R-7JRFT USER'S MANUAL ‫מתח בפנל האחורי‬ !‫הרה‬ ‫אז‬ ‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת. יש להיזהר במהלך‬ .‫העבודה‬ ‫ﺍﻟﻠﻮﺣﺔ‬ ‫ﺃﻭﺍﻟﻄﺎﻗﺔ ﺍﻟﻤﻮﺟﻮﺩﺓ ﻋﻠﻰ‬ ‫ﺍﻟﺘﻴﺎﺭ ﺍﻟﻜﻬﺮﺑﺎﺋﻲ‬ ‫ﻣﻦ‬ ‫ﺧﻄﺮ‬ ‫ﻫﻨﺎﻙ‬ ‫ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ‬ ‫ﺧﺪﻣﺔ‬ ‫ﻛﻦ ﺣﺬﺭﺍ ﻋﻨﺪ‬ ‫ﻳﻌﻤﻞ‬ ‫ﺍﻟﻨﻈﺎﻡ‬ ‫ﻋﻨﺪﻣﺎ ﻳﻜﻮﻥ‬...

  • Page 47: Product Disposal

    Chapter 4: Warning Statements for AC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. ‫תיאום חוקי החשמל הארצי‬ !‫אזהרה‬ ‫הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬ ‫התקנת‬ ‫ﺍﻟﻤﺘﻌﻠﻘﺔ‬ ‫ﺍﻟﻤﺤﻠﻴﺔ ﻭﺍﻟﻮﻁﻨﻴﺔ‬ ‫ﻘﻮﺍﻧﻴﻦ‬ ‫ﻳﺠﺐ ﺃﻥ ﻳﻤﺘﺜﻞ ﻟﻠ‬ ‫ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬...

  • Page 48: Hot Swap Fan Warning

    SUPERSERVER 8047R-7JRFT USER'S MANUAL ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
  • Page 49 Chapter 4: Warning Statements for AC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.

  • Page 50: Power Cable And Ac Adapter

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Power Cable and AC Adapter Warning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certifi...
  • Page 51 Chapter 4: Warning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifi...
  • Page 52 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes 4-20...

  • Page 53: Chapter 5 Advanced Serverboard Setup

    Chapter 5: Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install the X9QR7-TF-JBOD serverboard into the chassis, connect the data and power cables and install add-on cards. All serverboard jumpers and connections are also described. A layout and quick reference chart are included in this chapter for your reference.

  • Page 54: Connecting Cables

    (make sure the red wires connect to the pin 1 locations). If you are confi guring the system, keep the airfl ow in mind when routing the cables. The following cables need to be connected for the SuperServer 8047R-7JRFT system: •...

  • Page 55: Control Panel Connectors And I/O Ports

    Chapter 5: Advanced Serverboard Setup Control Panel Connectors and I/O Ports The rear I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-1 below for the colors and locations of the various I/O ports. Figure 5-1.

  • Page 56: Connecting The Control Panel

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Connecting the Control Panel JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indicators. Even and odd numbered pins are on opposite sides of each header.

  • Page 57: Processor And Heatsink Installation

    Chapter 5: Advanced Serverboard Setup Processor and Heatsink Installation Caution! When handling the processor package, avoid placing direct pressure on the label area. Note: Always connect the power cord last, and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink.
  • Page 58 SUPERSERVER 8047R-7JRFT USER'S MANUAL 2. Press the second load lever labeled 'Close 1st' to release the load plate that covers the CPU socket from its locking position. Press down on the load Pull the lever away lever labeled 'Close 1st' from the socket 3.
  • Page 59 Chapter 5: Advanced Serverboard Setup 4. Use your index fi ngers to loosen the lever and open the load plate. 5. Use your thumb and index fi nger to hold the CPU on its edges. Align the CPU keys, which are semi-circle cutouts, against the socket keys. Socket Keys CPU Keys...
  • Page 60 SUPERSERVER 8047R-7JRFT USER'S MANUAL 6. Once they are aligned, carefully lower the CPU straight down into the socket. (Do not drop the CPU on the socket. Do not move the CPU horizontally or vertically. Do not rub the CPU against the surface or against any pins of the socket to avoid damaging the CPU or the socket.)
  • Page 61 Chapter 5: Advanced Serverboard Setup 7. With the CPU inside the socket, inspect the four corners of the CPU to make sure that the CPU is properly installed. 8. Close the load plate with the CPU inside the socket. Lock the lever labeled 'Close 1st' fi...

  • Page 62: Installing A Passive Cpu Heatsink

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Installing a Passive CPU Heatsink 1. Do not apply any thermal grease to the heatsink or the CPU die -- the required amount has already been applied. 2. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the Serverboard's and the Heatsink Bracket underneath.

  • Page 63: Removing The Heatsink

    Chapter 5: Advanced Serverboard Setup Removing the Heatsink Caution: We do not recommend that the CPU or the heatsink be removed. However, if you do need to uninstall the heatsink, please follow the instructions below to uninstall the heatsink to prevent damage done to the CPU or the CPU socket. 1.

  • Page 64: Installing Memory

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Installing Memory Caution: exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Installing Memory Installing & Removing DIMMs 1. Insert the desired number of DIMMs into the memory slots, starting with P1- DIMM #1A.
  • Page 65 Chapter 5: Advanced Serverboard Setup Figure 5-3. Installing DIMM into Slot To Install: Insert Notch Notch module vertically and press down until it snaps into place. Front View Pay attention to the alignment notch at the bottom. Note: Notch should align with To Remove: Use the receptive key point on the slot.

  • Page 66: Dimm Module Population Confi Guration

    SUPERSERVER 8047R-7JRFT USER'S MANUAL CPU1/CPU2 2 CPUs & P1-DIMMA1/P1-DIMMA2, P1-DIMMB1/P1-DIMMB2, P1-DIMMC1/P1-DIMMC2, P1- 16 DIMMs DIMMD1/P1-DIMMD2, P2-DIMME1/P2-DIMME2, P2-DIMMF1/P2-DIMMF2, P2-DIMMG1/ P2-DIMMG2, P2-DIMMH1/P2-DIMMH2 CPU1/CPU2/CPU3/CPU4 4 CPUs & P1-DIMMA1/P1-DIMMA2/P1-DIMMB1/P1-DIMMB2, P2-DIMME1/P2-DIMME2/P2-DIMMF1/ 18~32 DIMMs P2-DIMMF2, P3-DIMMJ1/P3-DIMMK1, P4-DIMMN1/P4-DIMMP1+ any DIMM pairs in the available DIMM slots DIMM Module Population Confi guration Note 1: For the memory modules to work properly, please install DIMM modules of the same type, same speed and same operating frequency on the serverboard.
  • Page 67 Chapter 5: Advanced Serverboard Setup Populating RDIMM (ECC) Memory Modules Intel E5-4600 Series Processor RDIMM Memory Support Ranks Memory Capacity Speed (MT/s) and Voltage Validated by Slot Per DIMM Per DIMM per Channel (SPC) and DIMM Per Channel & Data (DPC) Width (See the Note Below)

  • Page 68: Adding Pci Expansion Cards

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Adding PCI Expansion Cards The 8047R-7JRFT includes one preinstalled riser cards designed specifi cally for use in the SC848E16-R1K628 4U rackmount chassis. These riser cards support one low-profi le PCI Express x16 cards to fi t inside the chassis for each node.

  • Page 69: Serverboard Details

    Chapter 5: Advanced Serverboard Setup Serverboard Details Figure 5-4. X9QR7-TF-JBOD Serverboard Layout (not drawn to scale) USB0/1 USB2/3 COM1 JUIDB1 LAN CTRL FAN4 KB/MOUSE IPMI_LAN LAN2 LAN1 CPU3 CPU2 CPU4 CPU2 X9QR7-F/-TF/-JTF Rev. 1.01 CPU1 CPU2 CPU2 CPU2 LEDS3 LEDS4 LEDS5 Notes: 1.
  • Page 70 SUPERSERVER 8047R-7JRFT USER'S MANUAL X9QR7-TF-JBOD Quick Reference Jumper Description Default Setting JBT1 Clear CMOS See Section 5-9 2 C1/JI SMB to PCI-E Slots Off (Disabled) JPB1 BMC Enable Pins 1-2 (Enabled) JPG1 VGA Enable Pins 1-2 (Enabled) JPS1 SAS Enable for SAS 0~3, SAS...
  • Page 71 Chapter 5: Advanced Serverboard Setup (CPU4) Slots 3/4 PCI-Express 3.0 x16 Slots (Available w/CPU4 installed) (CPU3) Slots 5/6 PCI-Express 3.0 x16 Slots (Available w/CPU3 installed) (CPU2) Slots 7/8 PCI-Express 3.0 x16 Slots (Available w/CPU2 installed) Internal Speaker/Buzzer T-SGPIO 1/2/3 Serial_Link General Purpose I/O Headers Unit Identifi...

  • Page 72: Connector Defi Nitions

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Connector Defi nitions Power Connectors ATX Power 24-pin Connector Pin Defi nitions A 2 4 - p i n m a i n p o w e r s u p p l y Pin# Defi nition Pin # Defi...
  • Page 73 Chapter 5: Advanced Serverboard Setup Reset Connector Reset Button Pin Defi nitions The reset connector is located on pins 3 (JF1) and 4 of JF1 and attaches to the reset Pin# Defi nition switch on the computer chassis. See the Reset table on the right for pin defi...
  • Page 74 SUPERSERVER 8047R-7JRFT USER'S MANUAL HDD LED HDD LED Pin Defi nitions The HDD LED connection is located (JF1) on pins 13 and 14 of JF1. Attach the Pin# Defi nition hard drive LED cable here to display 3.3V Standby disk activity (for any hard drives on the...
  • Page 75 Chapter 5: Advanced Serverboard Setup Universal Serial Bus (USB) Type A USB (USB 8/9) Four Universal Serial Bus ports (USB Pin Defi nitions 2/3, USB 0/1) are located on the I/O back Pin# Defi nition panel. Four USB headers (USB 4/5 and USB 6/7) provide front-accessible USB connections.

  • Page 76: System Management Bus Header

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Ethernet LAN Ports 10 Gb LAN Ports (LAN1/2) Pin Defi nition Two 10 Gigabit Ethernet ports (LAN1/2) Pin# Defi nition Pin# Defi nition are located on the I/O backplane on the serverboard. In addition, an IPMI...
  • Page 77 Chapter 5: Advanced Serverboard Setup Unit Identifi er Switch UID Switch A Unit Identifier Switch (UIDB1) and Pin# Defi nition two LED Indicators are located on the Ground serverboard. The UID Switch is located Ground next to the LAN ports on the backplane. Button In The Rear UID LED (LED11) is located Ground...
  • Page 78 SUPERSERVER 8047R-7JRFT USER'S MANUAL Power SMB (I2C) Connector PWR SMB (JPI Pin Defi nitions Power System Management Bus (I Pin# Defi nition Connector (JPI C1) monitors power Clock supply, fan and system temperatures. Data See the table on the right for pin defi...
  • Page 79 Chapter 5: Advanced Serverboard Setup Internal Speaker Internal Buzzer Pin Defi nition The Internal Speaker, located at SP1, can Pin# Defi nitions be used to provide audible indications Pin 1 Pos. (+) Beep In for various beep codes. See the table Pin 2 Neg.

  • Page 80: Jumper Settings

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Jumper Settings Connector Pins Explanation of Jumpers To modify the operation of the serverboard, Jumper jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function Setting of the connector. Pin 1 is identifi ed with a square solder pad on the printed circuit board.
  • Page 81 Chapter 5: Advanced Serverboard Setup BMC Enable BMC Enable (JPB1) Jumper Settings Jumper JPB1 allows you to enable the Jumper Setting Defi nition onboard BMC (Baseboard Management) Pins 1-2 BMC Enable (Default) Controller to provide IPMI 2.O/KVM Pins 2-3 Normal support on the serverboard.

  • Page 82: 5-10 Onboard Indicators

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Watch Dog Enable/Disable Watch Dog (JWD1) Jumper Settings Watch Dog (JWD1) is a system monitor Jumper Setting Defi nition that can reboot the system when a Pins 1-2 Reset (default) software application hangs. Close Pins Pins 2-3...
  • Page 83 Chapter 5: Advanced Serverboard Setup GLAN LEDs There are two ethernet LAN ports on Link Speed Activity the serverboard. Each Ethernet LAN port has two LEDs. The Yellow LED on the right indicates connection and GLAN Activity Indicator activity. The Link LED on the left side (Right) LED Settings may be green, amber or off to indicate...

  • Page 84: 5-11 Sas/Serial Ata Ports

    SUPERSERVER 8047R-7JRFT USER'S MANUAL 5-11 SAS/Serial ATA Ports SAS Port Pin Defi nitions SAS2 Ports Pin # Defi nition Two sets of eight Serial Attached Ground SCSI ports (SAS 3.0 0~3, 4~7) are located at JS1/JS2 and JS14/JS15 on the serverboard to provide serial link Ground connections.

  • Page 85: 5-12 Installing Drivers

    Chapter 5: Advanced Serverboard Setup 5-12 Installing Drivers The CD that came bundled with the system contains drivers, some of which must be installed, such as the chipset driver. After inserting this CD into your CD-ROM drive, the display shown in Figure 5-6 should appear. (If this display does not appear, click on the My Computer icon and then on the icon representing your CD-ROM drive.

  • Page 86: Supero Doctor Iii

    SuperDoctor, as the SuperDoctor settings override the BIOS settings. To set the BIOS temperature threshold settings again, you would fi rst need to uninstall SuperDoctor. Figure 5-7. Supero Doctor III Interface Display Screen (Health Information) 5-34...
  • Page 87 Chapter 5: Advanced Serverboard Setup Figure 5-8. Supero Doctor III Interface Display Screen (Remote Control) Note: The SuperDoctor III program and User’s Manual can be downloaded from the Supermicro web site at http://www.supermicro.com/products/accessories/software/ SuperDoctorIII.cfm. For Linux, we recommend that you use the SuperoDoctor II application instead.

  • Page 88: 5-13 Onboard Battery

    SUPERSERVER 8047R-7JRFT USER'S MANUAL 5-13 Onboard Battery Caution: There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarites (see Figure 5-9). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032).

  • Page 89: Chapter 6 Chassis Setup And Maintenance

    Chapter 6: Advanced Chassis Setup Chapter 6 Chassis Setup and Maintenance Overview This chapter covers the steps required to install components and perform mainte- nance on the chassis. The only tool you will need to install components and perform maintenance is a Phillips screwdriver. Print this chapter to use as a reference while setting up your chassis.

  • Page 90: Installing And Removing Hard Drives

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Installing and Removing Hard Drives Figure 6-1. Removing a Hard Drive Removing Hard Drive Trays from the Chassis 1. Press the release button on the drive tray. This extends the drive bay handle. 2. Use the handle to pull the drive out of the chassis.
  • Page 91 Chapter 6: Advanced Chassis Setup Figure 6-2. Chassis Drive Tray The drives are mounted in drive trays to simplify their installation and removal from the chassis. These trays also help promote proper airfl ow for the drive bays. Warning: Except for short periods of time (swapping hard drives), do not operate the server with the hard drives empty.
  • Page 92 SUPERSERVER 8047R-7JRFT USER'S MANUAL Figure 6-3. Installing a Hard Drive into the Tray Figure 6-4. Installing the Hard Drive...

  • Page 93: Accessing The Inside Of The System

    Chapter 6: Advanced Chassis Setup Accessing the Inside of the System Removing the Chassis Cover Remove this screw (If necessary) Figure 6-5. Removing the Chassis Cover Removing the Chassis Cover 1. Press the release tabs to remove the cover from the locked position. Press both tabs at the same time.

  • Page 94: Add-On Card/Expansion Slot Setup

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Add-on Card/Expansion Slot Setup The SC848 chassis includes I/O slots for add-on cards and expansion cards. Installing Add-on and Expansion Cards in the SC848 Chassis 1. Disconnect the power supply, lay the chassis on a fl at surface, and open the chassis cover.

  • Page 95: Installing The Air Shroud

    Air Shroud Part No. Description MCP-310-84805-0B Mylar air shroud for 8047R-7JRFT server system Installing the Air Shroud 1. Place the air shroud in the chassis, fi tting the air shroud between the middle bracket and the rear window.

  • Page 96: System Fans

    SUPERSERVER 8047R-7JRFT USER'S MANUAL System Fans Six heavy duty fans provide cooling for the chassis. These fans circulate air through the chassis as a means of lowering the chassis internal temperature. Release Tab Figure 6-8. Front System Fan Release Tab Release Tab Figure 6-9.
  • Page 97 Chapter 6: Advanced Chassis Setup Replacing a System Fan 1. If necessary, open the chassis while the power is running to determine which fan has failed. (Never run the server for an extended period of time with the chassis open.) 2.

  • Page 98: Power Supply

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Power Supply The SC848 chassis includes two 1620 Watt (1+1 redundant for a total of 3240 Watts) high-effi ciency, power supplies. These power supplies are auto-switching capable. This enables it to automatically sense and operate at a 100v to 240v input voltage.
  • Page 99 Chapter 6: Advanced Chassis Setup Changing the Power Supply 1. With the system running, unplug the AC power cord from the failed power supply module. 2. Push and hold the release tab on the back of the power supply. 3. Grasp the handle and pull the power supply out of its bay. 4.
  • Page 100 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes 6-12...

  • Page 101: Chapter 7 Bios

    Chapter 7: BIOS Chapter 7 BIOS Introduction This chapter describes the AMI BIOS Setup utility for the X9QRiF/X9QR7-TF/ X9QR7-JTF. It also provides the instructions on how to navigate the AMI BIOS Setup utility screens. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated.

  • Page 102: How To Change The Confi Guration Data

    SUPERSERVER 8047R-7JRFT USER'S MANUAL How To Change the Confi guration Data The confi guration data that determines the system parameters may be changed by entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing <Delete> at the appropriate time during system boot.
  • Page 103 Chapter 7: BIOS The AMI BIOS main menu displays the following information: System Date This item displays the system date in Day MM/DD/YY format (e.g. Wed 10/12/2012). System Time This item displays the system time in HH:MM:SS format (e.g. 15:32:52). Supermicro X9QR7-TF Version This item displays the SMC version of the BIOS ROM used in this system.

  • Page 104: Advanced Setup Confi Gurations

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Advanced Setup Confi gurations Use the arrow keys to select Advanced Setup and press <Enter> to access the following submenu items. Boot Features Quiet Boot This feature allows the user to select bootup screen display between POST mes- sages and the OEM logo.
  • Page 105 Chapter 7: BIOS Interrupt 19 Capture Interrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Immediate, the ROM BIOS of the host adaptors will immediately "capture" Interrupt 19 at bootup and allow the drives that are attached to these host adaptors to function as bootable disks.
  • Page 106 SUPERSERVER 8047R-7JRFT USER'S MANUAL • Microcode Patch • CPU Stepping • Maximum CPU Speed • Minimum CPU Speed • Processor Cores • Intel HT (Hyper-Threading) Technology • Intel VT-x Technology • Intel SMX Technology • L1 Data Cache • L1 Code Cache •...
  • Page 107 Chapter 7: BIOS Active Processor Cores Set to Enabled to use a processor's second core and above. (Please refer to Intel's website for more information.) The options are All, 1, 2, and 4. Limit CPUID Maximum This feature allows the user to set the maximum CPU ID value. Enable this function to boot the legacy operating systems that cannot support processors with extended CPUID functions.
  • Page 108 SUPERSERVER 8047R-7JRFT USER'S MANUAL Intel ® Virtualization Technology (Available when supported by the CPU) Select Enabled to support Intel Virtualization Technology, which will allow one platform to run multiple operating systems and applications in independent parti- tions, creating multiple "virtual" systems in one physical computer. The options are Enabled and Disabled.
  • Page 109 Chapter 7: BIOS CPU C6 Report (Available when Power Technology is set to Custom) Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to the operating system. During the CPU C6 State, the power to all cache is turned off.

  • Page 110: North Bridge

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Short Duration Power Limit This item displays the time period during which short duration power (in watts) is maintained. The default setting is 0. Chipset Confi guration North Bridge This feature allows the user to confi gure the settings for the Intel North Bridge.
  • Page 111 Chapter 7: BIOS CPU2 Slot8 PCI-E Link Speed Select GEN1 to enable PCI-Exp Generation 1 support for Slot 8. Select GEN2 to enable PCI-Exp Generation 2 support for Slot 8. Select GEN3 to enable PCI-Exp Generation 3 support for Slot 8. The options are GEN1, GEN2, and GEN3. CPU2 Slot7 PCI-E Link Width This feature allows the user to set the PCI-Exp bus speed between CPU2 and the PCI-e port.
  • Page 112 SUPERSERVER 8047R-7JRFT USER'S MANUAL CPU3 Slot5 PCI-E Link Width This feature allows the user to set the PCI-Exp bus speed between CPU2 and the PCI-e port. The options are x4, x8, and x16. CPU3 Slot5 PCI-E Link Speed Select GEN1 to enable PCI-Exp Generation 1 support for Slot 7. Select GEN2 to enable PCI-Exp Generation 2 support for Slot 7.
  • Page 113 Chapter 7: BIOS QPI (Quick Path Interconnect) Link Speed Mode Use this feature to select data transfer speed for QPI Link connections. The options are Fast and Slow. QPI Link Frequency Select Use this feature to select the desired QPI frequency. The options are Auto, 6.4 GT/s, 7.2 GT/s, 8.0 GT/s, and 16.0 GT/s.
  • Page 114 SUPERSERVER 8047R-7JRFT USER'S MANUAL DDR Speed Use this feature to force a DDR3 memory module to run at a frequency other than what is specifi ed by the manufacturer. The options are Auto, Force DDR3- 800, Force DDR3-1066, Force DDR3-1333, Force DDR3-1600 and Force SPD.
  • Page 115 Chapter 7: BIOS South Bridge Confi guration This feature allows the user to confi gure the settings for the Intel PCH chip. PCH Information This feature displays the following PCH information. Name: This item displays the name of the PCH chip. Stepping: This item displays the PCH stepping.
  • Page 116 SUPERSERVER 8047R-7JRFT USER'S MANUAL SATA Mode Use this feature to confi gure SATA mode for a selected SATA port. The options are Disabled, IDE Mode, AHCI Mode and RAID Mode. The following are displayed depending on your selection: IDE Mode...
  • Page 117 Chapter 7: BIOS SCU (Storage Control Unit) Confi guration Storage Controller Unit Select Enabled to enable PCH SCU storage devices. The options are Disabled and Enabled. OnChip SCU Option ROM Select Enabled to support the onboard SCU Option ROM to boot up the system via a storage device.
  • Page 118 SUPERSERVER 8047R-7JRFT USER'S MANUAL Maximum Read Request Select Auto to allow the system BIOS to automatically set the maximum Read Request size for a PCI-E device to enhance system performance. The options are Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
  • Page 119 Chapter 7: BIOS Network Stack Select Enabled enable PXE (Preboot Execution Environment) or UEFI (Unifi ed Extensible Firmware Interface) for network stack support. The options are Enabled and Disabled. IPv4 PXE Support (Available when Network Stack is set to Enabled) Set this item to Enabled to activate IPv4 PXE Support.

  • Page 120: Serial Port Console Redirection

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Serial Port 2 Confi guration Serial Port Select Enabled to enable a serial port specifi ed by the user. The options are En- abled and Disabled. Device Settings This item displays the settings of Serial Port 2.
  • Page 121 Chapter 7: BIOS Terminal Type This feature allows the user to select the target terminal emulation type for Con- sole Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key support. Select ANSI to use the Extended ASCII Char- acter Set.
  • Page 122 SUPERSERVER 8047R-7JRFT USER'S MANUAL Recorder Mode Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server. The options are Disabled and Enabled. Resolution 100x31 Select Enabled for extended-terminal resolution support. The options are Dis- abled and Enabled.

  • Page 123: Acpi Settings

    Chapter 7: BIOS Bits Per Second This item sets the transmission speed for a serial port used in Console Redirec- tion. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 57600, and 115200 (bits per second).
  • Page 124 SUPERSERVER 8047R-7JRFT USER'S MANUAL Trusted Computing (Available when a TPM device is detected by the BIOS) Confi guration TPM Support Select Enabled on this item and enable the TPM jumper on the serverboard to enable TPM support to improve data integrity and network security. The options are Enabled and Disabled.
  • Page 125 Chapter 7: BIOS Intel TXT (LT-SX) Confi guration This feature displays the following TXT confi guration setting. TXT Support: This item indicates if the Intel TXT support is enabled or disabled. The default setting is Disabled. Intel TXT (LT-SX) Dependencies This feature displays the features that need to be enabled for the Intel Trusted Execution Technology to work properly in the system.

  • Page 126: Event Logs

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Event Logs Use this feature to confi gure Event Log settings.  Change SMBIOS Event Log Settings This feature allows the user to confi gure SMBIOS Event settings. Enabling/Disabling Options SMBIOS Event Log Select Enabled to enable SMBIOS (System Management BIOS) Event Logging during system boot.
  • Page 127 Chapter 7: BIOS Erasing Settings Erase Event Log Select Enabled to erase the SMBIOS (System Management BIOS) Event Log, which is completed before an event logging is initialized upon system reboot. The options are No, Yes, next reset, and Yes, every reset. When Log is Full Select Erase Immediately to immediately erase SMBIOS error event logs that ex- ceed the limit when the SMBIOS event log is full.

  • Page 128: Ipmi

    SUPERSERVER 8047R-7JRFT USER'S MANUAL IPMI Use this feature to confi gure Intelligent Platform Management Interface (IPMI) settings. IPMI Firmware Revision This item indicates the IPMI fi rmware revision used in your system. Status of BMC This item indicates the status of the IPMI fi rmware installed in your system.
  • Page 129 Chapter 7: BIOS When SEL is Full This feature allows the user to decide what the BIOS should do when the system event log is full. Select Erase Immediately to erase all events in the log when the system event log is full. The options are Do Nothing and Erase Immediately. Custom EFI Logging Options Log EFI Status Codes Select Enabled to log EFI (Extensible Firmware Interface) Status Codes, Error...

  • Page 130: Boot

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Gateway IP Address This item displays the Gateway IP address for this computer. This should be in decimal and in dotted quad form (i.e., 192.168.10.253). Boot This submenu allows the user to confi gure the following boot settings for the system.

  • Page 131: Security

    Chapter 7: BIOS Security This menu allows the user to confi gure the following security settings for the system. Administrator Password Use this feature to set the Administrator Password which is required to enter the BIOS setup utility. The length of the password should be from 3 characters to 20 characters long.

  • Page 132: Save & Exit

    SUPERSERVER 8047R-7JRFT USER'S MANUAL Save & Exit This submenu allows the user to confi gure the Save and Exit settings for the system. Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system confi...
  • Page 133 Chapter 7: BIOS Discard Changes Select this feature and press <Enter> to discard all the changes and return to the BIOS setup. When the dialog box appears, asking you if you want to load previ- ous values, select Yes to load the values previous saved, or select No to keep the changes you've made so far.
  • Page 134 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes 7-34...

  • Page 135: Appendix A Bios Error Beep Codes

    Appendix A: BIOS Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed at each system boot, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue to boot.
  • Page 136 SUPERSERVER 8047R-7JRFT USER'S MANUAL Notes...

  • Page 137: Appendix B System Specifi Cations

    Hard Drive Bays The SuperServer 8047R-7JRFT contains twenty-four hot-swap drive bays. PCI Expansion The SuperServer 8047R-7JRFT has eight PCI Express 3.0 x16 slots available. Serverboard X9QR7-TF-JBOD serverboard (proprietary form factor) Dimensions: (LxW) 17 x 17 in. (432 mm x 432 mm)
  • Page 138 SUPERSERVER 8047R-7JRFT USER'S MANUAL Weight Gross (Bare Bone): 100 lbs. (45.4 kg.) System Cooling The system has two 8-cm PWM system cooling fans and four 9-cm colling fans. System Input Requirements AC Input Voltage: 100-240V AC auto-range (1000W Output @ 100-120V, 12- 10A, 1200W Output @ 120-140V, 12-10A, 1620W Output @ 180-240V, 10.5-8A)
  • Page 139 Appendix B: System Specifi cations Notes...
  • Page 140 SUPERSERVER 8047R-7JRFT USER'S MANUAL (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in signifi...

Table of Contents