Table of Contents
Advertisement
Quick Links
The Embedded I/O Company
Transition Module for TIP866/TIP867
TEWS TECHNOLOGIES GmbH
Am Bahnhof 7
Phone: +49-(0)4101-4058-0
e-mail: info@tews.com
TIP866-TM-20
with 8 RJ45 Connectors
Version 1.0
User Manual
Issue 1.3
April 2003
D75866871
25469 Halstenbek / Germany
Fax: +49-(0)4101-4058-19
www.tews.com
TEWS TECHNOLOGIES LLC
1 E. Liberty Street, Sixth Floor
Phone: +1 (775) 686 6077
e-mail: usasales@tews.com
Reno, Nevada 89504 / USA
Fax: +1 (775) 686 6024
www.tews.com
Advertisement
Table of Contents
Related Manuals for Tews Technologies TIP866-TM-20
Summary of Contents for Tews Technologies TIP866-TM-20
- Page 1 Transition Module for TIP866/TIP867 with 8 RJ45 Connectors Version 1.0 User Manual Issue 1.3 April 2003 D75866871 TEWS TECHNOLOGIES GmbH TEWS TECHNOLOGIES LLC Am Bahnhof 7 25469 Halstenbek / Germany 1 E. Liberty Street, Sixth Floor Reno, Nevada 89504 / USA Phone: +49-(0)4101-4058-0...
- Page 2 However TEWS TECHNOLOGIES GmbH reserves the right to change the product described in this document at any time without notice. TEWS TECHNOLOGIES GmbH is not liable for any damage arising out of the application or use of the device described herein.
-
Page 3: Table Of Contents
Table of Contents PRODUCT DESCRIPTION ..................5 TECHNICAL SPECIFICATION................... 6 CONNECTOR X1 PIN ASSIGNMENT................ 7 RJ45 PIN ASSIGNMENT.................... 9 ASSEMBLY DRAWING.................... 10 TIP866-TM-20 User Manual Issue 1.3 Page 3 of 10... - Page 4 FIGURE 3-1 : CONNECTOR X1 PIN ASSIGNMENT ..................8 FIGURE 4-1 : PIN ASSIGNMENT OF RJ45 CONNECTOR TIP866-TM-20 CHANNEL 1 AND 2....9 FIGURE 4-2 : PIN ASSIGNMENT OF RJ45 CONNECTOR TIP866-TM-20 CHANNEL 3 TO 8 ......9 FIGURE 4-3 : RJ45 PINNING ...........................9 FIGURE 5-1 : ASSEMBLY DRAWING......................10...
-
Page 5: Product Description
TIP867-10 (RS485). This transition module can also be used with the IP-Octals. If the TIP866-TM-20 is used with the IP- Octal RS232: do not connect jumpers on J11, J12, J21, J22: 9-10 and 11-12 because the IP-Octal RS232 does not support DCD and DTR on serial channel 1 and 2. -
Page 6: Technical Specification
Power only required to supply on board termination or to provide +5V to pin 1 of the RJ45 connectors of channel 3 to 8. Fuse protected by a 1A Multifuse. MTBF 377345h Figure 2-1 : Technical Specification TIP866-TM-20 User Manual Issue 1.3 Page 6 of 10... -
Page 7: Connector X1 Pin Assignment
RXD5- CTS5 RXD5+ TXD6 TXD6- DX6- RXD6 TXD6+ DX6+ RTS6 RXD6- CTS6 RXD6+ TXD7 TXD7- DX7- RXD7 TXD7+ DX7+ RTS7 RXD7- CTS7 RXD7+ TXD8 TXD8- DX8- RXD8 TXD8+ DX8+ RTS8 RXD8- TIP866-TM-20 User Manual Issue 1.3 Page 7 of 10... -
Page 8: Figure 3-1 : Connector X1 Pin Assignment
TIP866-10 TIP866-20 TIP867-10 ( RS232 ) ( RS422 ) ( RS485) CTS8 RXD8+ DCD1 DTR1 DCD2 DTR2 nc = not connected on the TIP866-TM-20 Figure 3-1 : Connector X1 Pin Assignment TIP866-TM-20 User Manual Issue 1.3 Page 8 of 10... -
Page 9: Rj45 Pin Assignment
Default configuration for TIP866-TM-20: jumper installed on Jn1 => RS232 DTE. Channel 1 and 2 of the TIP866-TM-20 additionally support DCD and DTR for the TIP866-10. Support of +5V on pin 1 of the RJ45 connector for channel 3 to 8 is jumper selectable (Jn5: 9- 10) and requires +5V connected to connector X9 (2 pin screw terminal). -
Page 10: Assembly Drawing
5 Assembly Drawing Figure 5-1 : Assembly Drawing TIP866-TM-20 User Manual Issue 1.3 Page 10 of 10...
Need help?
Do you have a question about the TIP866-TM-20 and is the answer not in the manual?
Questions and answers