Specifications - Sharp XV-Z201E Operation Manual

Glossar
Aspect Ratio

Specifications

Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
Product type
of 16:9 and 21:9.
Model
Video system
Auto Sync
Optimizes projected computer images by auto-
Display method
matically adjusting certain characteristics.
DLP panel
Background
Initial setting image projected when no signal is
being output. Lens
Projection lamp
Clock
Video input signal
Clock adjustment is used to adjust vertical noise
S-video input signal
when clock level is incorrect.
CLR Temp (Colour temperature)
Component input signal
Function that can be used to adjust the colour tem-
(INPUT 1)
perature to suit the type of image input to the pro-
jector. Decrease the colour temperature to create
Component input signal
warmer, reddish images for natural flesh tones,
(INPUT 2)
or increase to create cooler, bluish images for a
brighter picture.
Composite sync
Signal combining horizontal and vertical sync
Horizontal resolution
pulses.
RGB input signal
Digital keystone correction
Function to digitally correct a distorted image when
the projector is set up at an angle, smoothes out
jaggies on keystone images and compresses the
image not only horizontally but vertically keeping
the 16 : 9 aspect ratio.
DVI (Digital Visual Interface)
Display digital interface that also supports analog
interfaces.
Pixel clock
Vertical frequency
Horizontal frequency
Computer control signal
Rated voltage
Input current
Rated frequency
Power consumption
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Downloaded From projector-manual.com Sharp Manuals
This SHARP projector uses a DMD chip. This very sophisticated chip contains 589,824 pixels. As with any high
Projector
XV-Z201E
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
I I
DTV 480 /480P/720P/1080
DLP chip, RGB optical shutter method
Panel size: 0.6
Display method: Single Panel Digital Micromirror Device (DMDª) by Texas Instruments
Drive method: Digital Light Processing (DLPª)
No. of dots: 589,824 dots (1,024 [H] 576 [V])
1Ð 1 .2 zoom lens, F2.0Ð 2 .4 f=16.9Ð 2 0.2 mm
210 W/168 W SHP lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75
P : 0.7 Vp-p, 75 terminated
B
P : 0.7 Vp-p, 75 terminated
R
29-pin connector
DVI input signal: Digital 250Ð 1 ,000 mV 50
Analog 0.7 Vp-p 75
Y: 1.0 Vp-p, sync negative, 75 terminated
P : 0.7 Vp-p, 75 terminated
B
P : 0.7 Vp-p, 75 terminated
R
520 TV lines (NTSC 3.58 input)
DVI-I terminal
<Digital>
Input impedance 50
Input level 250-1000 mV
<Analog>
Input impedance 75
Input level 0.7 Vp-p
<Synchronization signal>
Separate sync/Composite sync
Input level TTL level
Input impedance 1 K
Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75
12Ð 8 0 MHz
43Ð 7 5 Hz
15Ð 7 0 kHz
9-pin D-sub connector (RS-232C Port)
AC 100Ð 2 40 V
3.2 A
50/60 Hz
285 W
1,070 BTU/hour
5¡C to 35¡C
20¡C to 60¡C
Plastic
38 kHz
368 (W) 153.8 (H) 327 (D) mm (including swivel stand)
368 (W) 118 (H) 327 (D) mm (main body only)
4.6 kg (including swivel stand)
4.1 kg (main body only)
Remote control, Two AA size batteries, Power cord, 21 pin RCA conversion adaptor,
Video cable, Terminal cover, Screws for terminal cover, Lens cap (attached on the
body), Operation manual
Lamp unit (Lamp/cage module) (BQC-XVZ200++1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord for Europe except U.K.
(QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore
(QACCBA012WJPZ), Power cord for Australia and New Zealand (QACCLA018WJPZ),
21 pin RCA conversion adaptor (QSOCZ0361CEZZ), Video cable (QCNWGA001WJZZ),
Terminal cover (GCOVAA116WJKB), Screws for terminal cover (XBBSN40P10000), Lens
cap (CCAPHA004WJ01), Operation manuals; for European 7 languages (TINS-
B009WJZZ) / for Chinese, Korean and Arabic (TINS-B010WJZZ)
Gamma
Image quality enhancement function that offers a
richer image by brightening the darker portions of
the image without altering the brightness of the
brighter portions. You can select from four differ-
ent modes: Standard, Cinema 1, Cinema 2 and
Cinema 3.
Intelligent compression and expansion
High quality resizing of lower and higher resolu-
tion images to fit the projector's native resolution.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase level
is incorrect, the projected image typically displays
horizontal flicker.
Resize
terminated
Allows you to modify or customize the picture dis-
play mode to enhance the input image. You can
select from four different modes: SIDE BAR,
SMART STRETCH, CINEMA ZOOM and
STRETCH.
RS-232C
Function to control the projector from the com-
puter by using the RS-232C ports on the projec-
tor and computer.
Stretch
Mode that stretches the 4:3 image horizontally to
display it on the wide screen.
Sync on green
Video signal mode of a computer which overlaps
horizontal and vertical sync signal to green colour
signal pin.
-6