Sharp XV-Z201E Operation Manual page 21

Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust the projection height to match the setup configuration.
• The screen can be moved maximum the length of one screen vertically using the lens shift.
Note
Attaching the Swivel
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
Stand
Tilting or angling the projector will reduce the effectiveness of the lens shift function.
Screen size: 254 cm
1
trolling the Projector by a Computer
Align the tabs on the front bot-
Aspect ratio: 16:9
tom of the projector (• ).
Screen
2
While holding down the button
ng to a Computer
rolling the
( ), place the projector onto
90
the Swivel Stand ( ) to attach.
ector Using an
32C Cable
g to a Computer 3
he RS-232C terminal on the projector
Press the projector down
ected to a computer with an RS-232C
DVI to 15-pin
firmly to attach it to the Swivel
RGB
null modem, cross type, commercially
90
Stand to make sure it is se-
ptor and the
e), the computer can be used to con-
nt Using
curely attached to the Swivel
projector and check the status of the
(INPUT 2)
Lower edge of screen (White portion) =
in D-sub
or. See page 65 for details.
Stand.
Standard (0) point
VD Player and DTV Decoder
e RGB
a DVI to 15-pin D-sub
onnect an RS-232C cable to
2)
to the projector.
e projector.
b adaptor and the
Upper and Lower Lens Shift Position (Ceiling Mount)
Focusing and Zooming
RGB video equip-
the above adaptor to
When the projector is in the inverted position, use the upper edge of the screen as the base line,
nd DTV decoders
onnect the above cable to the
The picture can be focused and zoomed in or
cable.
and exchange the lower and upper lens shift values.
out by using the Focus ring and the Zoom
omputer.
knob.
Screen size: 254 cm
the above cable to the
15-pin D-sub
Aspect ratio: 16:9
1
Rotate the Focus ring until the
er.
ojector.
te
image on the screen comes
Screen
nectors by tightening the
ot connect or disconnect an RS-232C
into focus.
ve adaptor to to or from the computer while it is
ng com-
his may damage your computer.
players
2
90
Slide the Zoom knob. The im-
RS-232C function may not operate if
s.
computer terminal is not correctly set
age can be adjusted to the de-
uter Compatibility Chart" on
e cable to the
efer to the operation manual of the
sired size within the zoom
list of computer signals
uter for details.
ble to
range.
h the projector. Use with
to "Computer Compatibility Chart"
by tightening the s other than those listed may
ge 66 for a list of computer signals
he functions not to work.
atible with the projector. Use with
g the projector to a computer
90
uter signals other than those listed
to the
t "RGB" for "Signal Type" on
cause some of the functions not to
ment.
Using the Lens Shift
or press on the remote
jector to DVI out-
ge 52.)
The picture can be adjusted within the shift
select "RGB" for
ptor may be required for use
range of the lens by rotating the lens shift dial
D menu or press
osh computers. Contact your
on the top of the projector using your finger.
or and
l. (See page 52.)
uthorised Projector Dealer or
nnect-
e computer you are using, an
e projected unless the signal
the computer is switched to
ut. Refer to the computer op-
or switching the computer sig-
Downloaded From projector-manual.com Sharp Manuals
gs.
Lens centre
Optional
accessory
Optional
accessory
S-video cable
To INPUT 2 terminal
(commercially available)
To INPUT 3 terminal
To INPUT 1 terminals
To RGB output terminal
Component cable
(commercially available)
To analog component
To S-video output terminal
output terminal
1
DVI to 15-pin D-sub adaptor
Lens centre
Type: AN-A1DV (20 cm)
DVI to 15-pin D-sub adaptor
Type: AN-A1DV (20 cm)
To RS-232C terminal
RS-232C cable
(commercially available)
To INPUT 2 terminal
DVI to 15-pin D-sub adaptor
(sold separately)
Projected Image
DVI to 15-pin
D-sub adaptor
RGB cable
(sold separately)
(commercially available)
To RS-232C terminal
RGB cable
(commercially
Notebook computer
available)
3
Lower lens shift position
(High mount setup)
2
Upper lens shift position
(Desktop setup)
Zoom knob
Focus ring
Lens shift dial
UP
DOWN
Desktop computer
-27