Sharp XV-Z201E Operation Manual page 19

Upper and Lower Lens Shift Position
• This projector is equipped with a lens shift function that lets you adjust the projection height.
• Adjust the projection height to match the setup configuration.
• The screen can be moved maximum the length of one screen vertically using the lens shift.
Note
Attaching the Swivel
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
Stand
Tilting or angling the projector will reduce the effectiveness of the lens shift function.
Screen size: 254 cm
1
trolling the Projector by a Computer
Align the tabs on the front bot-
Aspect ratio: 16:9
tom of the projector (• ).
Screen
2
While holding down the button
rolling the
( ), place the projector onto
90
the Swivel Stand ( ) to attach.
ector Using an
32C Cable
g to a Computer 3
he RS-232C terminal on the projector
Press the projector down
ected to a computer with an RS-232C
DVI to 15-pin
firmly to attach it to the Swivel
RGB
null modem, cross type, commercially
90
Stand to make sure it is se-
ptor and the
e), the computer can be used to con-
nt Using
curely attached to the Swivel
projector and check the status of the
(INPUT 2)
Lower edge of screen (White portion) =
in D-sub
or. See page 65 for details.
Stand.
Standard (0) point
VD Player and DTV Decoder
e RGB
a DVI to 15-pin D-sub
onnect an RS-232C cable to
2)
to the projector.
e projector.
b adaptor and the
Upper and Lower Lens Shift Position (Ceiling Mount)
Focusing and Zooming
RGB video equip-
the above adaptor to
When the projector is in the inverted position, use the upper edge of the screen as the base line,
nd DTV decoders
onnect the above cable to the
The picture can be focused and zoomed in or
cable.
and exchange the lower and upper lens shift values.
out by using the Focus ring and the Zoom
omputer.
knob.
Screen size: 254 cm
the above cable to the
15-pin D-sub
Aspect ratio: 16:9
1
Rotate the Focus ring until the
er.
ojector.
ote
image on the screen comes
Screen
into focus.
ve adaptor to
ng com-
players
2
90
Slide the Zoom knob. The im-
s.
age can be adjusted to the de-
uter Compatibility Chart" on
e cable to the
sired size within the zoom
list of computer signals
ble to
range.
h the projector. Use with
"Computer Compatibility Chart"
s other than those listed may
ge 66 for a list of computer signals
he functions not to work.
atible with the projector. Use with
90
uter signals other than those listed
to the
"RGB" for "Signal Type" on
cause some of the functions not to
ment.
Using the Lens Shift
or press on the remote
ge 52.)
The picture can be adjusted within the shift
"RGB" for
range of the lens by rotating the lens shift dial
D menu or press
on the top of the projector using your finger.
or and
l. (See page 52.)
nnect-
Downloaded From projector-manual.com Sharp Manuals
Lens centre
Optional
accessory
Optional
accessory
S-video cable
To INPUT 2 terminal
(commercially available)
To INPUT 3 terminal
To INPUT 1 terminals
To RGB outp
Component cable
(commercially available)
To analog component
To S-video output terminal
output terminal
1
DVI to 1
Type: AN
DVI to 15
Type: AN
Lens centre
To RS-232C terminal
To INPUT
RS-232C cable
(commercially available)
DVI to 15-pi
(sold separa
RGB cable
(commerciall
Projected Image
DVI to 15-pin
D-sub adaptor
(sold separately)
To RS-232C terminal
Notebook co
RGB cable
(commercially
available)
3
Lower lens shift position
(High mount setup)
2
Upper lens shift position
(Desktop setup)
Zoom knob
Focus ring
Lens shift dial
UP
DOWN
Desktop computer
-27