Table of Contents
Advertisement
Contents:
How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Quick Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing the Outside Antenna . . . . . . . . . . . . . . . . . . . . . . 2
Installing the Low-Profile Antenna . . . . . . . . . . . . . . . . . . . 3
Installing a Wilson Electronics Signal Booster . . . . . . . . . . 3
Powering Up a Wilson Electronics Signal Booster . . . . . . 3
Understanding the Signal Booster Lights . . . . . . . . . . . . . 4
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . 4
Guarantee and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Appearance of device and accessories may vary .
Note: This manual contains important safety and operating information .
Please read and follow the instructions in this manual . Failure to
do so could be hazardous and result in damage to your Signal
Booster .
Mobile 4G
Smart Technology
Signal Booster
™
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wilson Electronics 460008
Summary of Contents for Wilson Electronics 460008
- Page 1 Installing the Low-Profile Antenna . . . . . . . . . . . . . . . . . . . 3 Installing a Wilson Electronics Signal Booster . . . . . . . . . . 3 Powering Up a Wilson Electronics Signal Booster .
- Page 2 Model # 460008 FCC ID: PWO460008 KIT CONFIGURATION Wilson Electronics manufactures a wide variety of antennas to help you customize your Signal Booster for your specific application . See your dealer or visit www.WilsonElectronics.com . INSIDE ANTENNA OPTIONS DC power supply 5V / 2 .5A (859948)
- Page 3 Before Getting Started This guide will help you properly install your Wilson Electronics Five Band Mobile Wireless Signal Booster . It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment .
- Page 4 ON/OFF SWITCH IMPORTANT: Do not power up the Signal Booster unless antenna cables are attached to Signal Booster . Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7am to 6 pm MST.
- Page 5 (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment . Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com...
- Page 6 Signal Boosters improve network cell phone areas without compromising carrier systems . All products are engineered and assembled in the company’s 100,000 square-foot headquarters in St . George, Utah . Wilson Electronics has product dealers in all 50 states as well as in countries around the world .
- Page 7 Returned Material Authorization (RMA) number supplied by Wilson Electronics . Wilson Electronics shall, at its option, either repair or replace the product . Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer within the continental U .S .
- Page 8 . After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. Wilson Electronics, LLC 3301 East Deseret Drive, St . George, UT 84790 For additional Technical Support visit www .WilsonElectronics .com...
Need help?
Do you have a question about the 460008 and is the answer not in the manual?
Questions and answers