Table of Contents
Advertisement
HOW TO USE BLUE LIGHT
When the product is powered on, the blue light at the middle panel will be on. In order to turn
off the blue light, you should keep the lamp buton pushed for 5 seconds. When the light is off,
if you push lamp buton for 5 seconds, blue light will be on. During that position, blue light will
be always on, when the product is off.
5 Speed LCD Control Usage
On/Off Button: (
) This button starts and stops the motor. Starting speed of the motor is 2nd
speed.
–Button: Decreases speed. Speed can be reduced till 1st speed. When you press this button
longer, 1 speed level is decreased each half seconds.
+ Button: Increases speed. Speed can be increased up to 5th Speed. When you press this button
longer, 1 speed level is increased each half seconds. When the cooker hood is set to 5th speed,
motor will operate at 5th speed for 15 minutes then will continue operating at 2nd speed. 5th
speed is turbo speed.
Timer - Button: (
) It is used for setting the time that timer will start operating decreasing the
time. Timer decreases 1 level at each press; if the button is pushed longer level will decrease fast.
Timer + Button:( ) It is used for setting the time that timer will start operating increasing the time.
Timer increases 1 level at each press; if the button is pushed longer level will increase fast.
Cooker-hood has timer function for two different
usages:
1-Timer for stopping the cooker-hood: If the timer is set when the motor is operating, cooker-hood
will stop, lamp will be off and buzzer will ring for 5 seconds when timer period is over.
2-Timer for alarm: If the timer is set when the motor is not operating, alarm timer will have been
started. When the timer is over, buzzer will ring for 15 seconds; even though motor is operated or
the lamps are set to on position when the timer is operating, motor will not stop operating and lamp
will not be off. When timer is not set, timer clock shows the real time.
Clock: Clock on LCD screen shows actual time. Two points between the hour and the minute
flashes each 1 second. In order to set hour, Tmr+ ( ) and Tmr- buttons are pushed at the same
time. Hour and minute flashe for 5 seconds. During flashing, pressing Tmr+ (
button minute will operate changing clock. During flashing, hour can be set using Tmr- or Tmr+
buttons, time can be set. (Settings will be reset in case of electricity cut or failure)
Filter Cleaning Warning : Filter cleaning icon appear on the screen after the cooker hood is
operated for 60 hours and it flashes each second to remind to wash aluminum filter. Pressing
on/off button for 3 seconds, filter time can be reset and filter icon can be removed.
Motor
on/off
) or Tmr- (
Timer
Lamp
step
on/off
-14-
Chimney Fixing Bar Screws;
Drill holes on the wall via Ø6 mm driller. Fix the chimney fixing
bar via 3,9 x 22 Ysb screws on Ø6 mm plastic dowels.
Drill holes on the wall via Ø10 mm driller. Fix 2 pcs of 5,5 x 60
Ysb screws on A,B points on Ø10 mm plastic dowels.
The distance between the wall and screw top should be 5mm.
Figure 6
Placing Range Hood on The Wall
Hang L shaped hanging bars on A and B points (Figure 7)
)
Tighten the Hanging Screws:
Tighten screws after hanging to fix your product via
screwdriver. You may use the M5x40Ysb screws to have fine
tune parallelism of hood. Figure 8
Note: You may fine tune parallelism by easing M5 screws on
the top.
5,5 x 60 Ysb
3,9 x 22 Ysb
Screw
Screw
Figure 7
Figure 8
-7-
D
E
A
B
G
C
H
Figure 6
Advertisement
Table of Contents
