Table of Contents
Advertisement
Entry Phone Specifications
Power: Telephone line powered. Minimum 18V DC talk
battery voltage with a minimum loop current of 20mA. Loop
current may be boosted on low current lines with a Viking
model TBB-1B Talk Battery Booster (see DOD 632).
Dimensions: Faceplate: 123.8mm x 125.4mm x 4.3mm
(4.875" x 4.938" x 0.17"), Phone: 72mm x 46mm x 42mm
(2.84" x 1.8" x 1.65")
Shipping Weight: 0.55 kg (1.2 lbs)
Speaker Volume: Approximately 62db maximum @ 1m
Ring Voltage: 25V AC RMS minimum (for auto answer)
CPC Disconnect Time: 300ms minimum
REN: 0.8A
Operating Temperature: -34°C to 65°C (-30°F to 150°F)
Humidity: Standard model: 5% to 95% non-condensing,
EWP model: Up to 100%
Connections: (5) gel-filled butt connectors (3M Scotchlok
UR2)
Recommended Electrical Box for Flush Mounting:
Double gang with minimum inside dimensions of 2.25" deep
x 3.65" wide x 2.84" tall (Carlon BH234R or equivalent)
Recommended Surface Mount Box: Viking model VE-5x5
(DOD# 424)
WARNING: Do NOT use a typical "wet location box" as not
all styles seal properly with the E-70 faceplate.
Faceplate:
18 guage 304 stainless steel
faceplate with super durable UV stable powder
paint to prevent fading and resist scratching.
Proximity Card Reader:
26-bit Wiegand,
125KHz, red LED turns off and transducer will
beep during card read. Fully potted EWP. Read
range
1.25"
to
2.0".
Impact
polycarbonate lens with water-tight gasket.
Mounting Screws: 6-32 x 1.25" long flathead
with 5/64" hexdrive, 18-8 stainless steel to
prevent corrosion.
Entry Phone Board: Compact analog speaker
phone with call progress detection for automatic
disconnect.
Microphone Volume
Speaker Volume
Earth Ground: To increase surge protection,
loosen the screw labeled
fasten a wire with ring terminal (included) from
the mounting screw to Earth Ground (grounding
rod, water pipe, etc.)
2
Features Overview
resistant
VIKING
VIKING
(as shown) and
Specifications
Proximity Card Reader Specifications
Power: 5 to 14V DC @ 60mA maximum
Maximum Cable Length: 500 ft 24 Awg stranded shielded
(Belden 9537)
Frequency: 125KHz
Format: 26 bit Wiegand
Read Range: 1.25" to 2.0"
Technologies Supported: Viking PRX-C, PRX-C-ISO,
PRX-FOB, certain legacy HID® proximity protocols* and
certain AWID 125Khz proximity protocols**
Transducer: Beeps during card read
LED: Red, turns off during card read
Humidity: Up to 100% (fully potted EWP)
Operating Temperature: -34° C to 65° C (-30° F to 150°
F)
* HID and the HID logo are registered trademarks of HID
Global Corporation, an ASSA ABLOY company. All other
trademarks are the property of their respective owners.
** AWID is a trademark of Applied Wireless Identification
Group.
Speaker Screen: Fiberglass Reinforced Plastic
speaker screen with 0.028" slots to prevent
punctures from paperclips, etc.
Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.
Blue LED:
Helps locate the push button,
indicate ringing and off-hook conditions.
Push Button Switch:
Push to initiate call,
push again to disconnect. Solid 304 stainless
steel internally sealed per IP67.
Microphone:
Omni-directional microphone
with protective water-resistant cloth.
Faceplate Gasket: 1/8" thick closed cell PVC
to provide a water-tight seal.
DIP Switches (see page 6):
1: Auto Answer Feature (on/off)
2: Dial Tone Detection (on/off)
3: Programming Switch (normal/programming)
4: LED (on/off)
Advertisement
Table of Contents
