Table of Contents
Advertisement
Quick Links
Instruction Manual
2015
Pneudraulic Installation Tools
Patent Pending
series
February 8, 2017
Declaration of Conformity
Disassembly Instructions
Assembly Instructions
Components Drawings
Makers of Huck
Brand Fasteners, Tools & Accessories
HK958
4-6
10-11
13-14
16-20
Troubleshooting
Kits and Accessories
21-22
, Marson
, Recoil
®
®
®
2
3
4
4
7
8
9
12
15
21
Advertisement
Table of Contents
Related Manuals for Arconic 2015 series
Summary of Contents for Arconic 2015 series
-
Page 1: Table Of Contents
Declaration of Conformity Safety Instructions Description Instruction Manual Principle of Operation 2015 series Pneudraulic Installation Tools Specifications Patent Pending Preparation for Use Operating Instructions Maintenance Disassembly Instructions 10-11 Assembly Instructions Fill and Bleed 13-14 Measuring Tool Stroke Components Drawings 16-20 Troubleshooting Kits and Accessories 21-22... - Page 2 2015 series Pneudraulic Installation Tools (HK958)
-
Page 3: Safety Instructions
2015 series Pneudraulic Installation Tools (HK958) Safety Instructions III. OPERATING HAZARDS: GLOSSARY OF TERMS AND SYMBOLS: 1. Use of tool can expose the operator’s hands to hazards including: crushing, impacts, cuts, abrasions and heat. Wear suitable gloves to protect hands. -
Page 4: Description
2015 series Pneudraulic Installation Tools (HK958) Description The 2015 series tools are lightweight, high-speed production When the tool is not in use, the OFF position (slider forward) tools that install 3/32” and 1/4” nail-type blind fasteners. An will prevent air loss. See Figure 5 for the location of this integral nose assembly increases reliability and simplifies use of assembly (pictured in the ON position) on the tool. - Page 5 2015 series Pneudraulic Installation Tools (HK958) pecificationS continued Models 2015 & 2015B...
- Page 6 2015 series Pneudraulic Installation Tools (HK958) pecificationS continued Model 2015V (8.8) (2.8) (4.0) Ø (1.9) (2.0) 10° Ø INCHES (cm) 12.0 (30.5) (12.4) Ø (8.8)
-
Page 7: Preparation For Use
2015 series Pneudraulic Installation Tools (HK958) reparation for WARNING: WARNING: As applicable, do not use without To avoid pinch points, be sure there is deflectors or pintail bottles. adequate clearance for tool and operator’s hands before proceeding. Tool moving If deflectors are removed or damaged,... -
Page 8: Operating Instructions
2015 series Pneudraulic Installation Tools (HK958) perating nStructionS Read all of these instructions in order to ensure the safe operation of this equipment. This section details installing Huck Blind Fasteners. WARNINGS: Review all CAUTIONs and WARNINGs prior to installing • Wear approved eye and hearing these fasteners. -
Page 9: Maintenance
2015 series Pneudraulic Installation Tools (HK958) aintenance GENERAL DAILY The operating efficiency of the tool is directly related to • Huck recommends using a filter-regulator-lubricator the performance of the entire system. Regular inspection unit. If one is not being used, uncouple the air... - Page 10 2015 series Pneudraulic Installation Tools (HK958) iSaSSeMbly This procedure is for complete disassembly of the tool. 13. Model 2013V: (Figure 5) Press the ring on the tube Disassemble only those components necessary to connector downward to release the tube. replace damaged O-rings, Quad-rings, Back-up rings, 14.
- Page 11 2015 series Pneudraulic Installation Tools (HK958) iSaSSeMbly continued 2015b 2015V & pecial iSaSSeMbly nStructionS for igure 1. Secure the head/handle in a vise. Remove the vacuum tube from the cylinder. (2015V only) 2. Rotate the pintail bottle until the retaining-ring holes are visible. Reach...
- Page 12 2015 series Pneudraulic Installation Tools (HK958) SSeMbly This procedure is for the assembly of the tool. For the dowel pin through holes in trigger and cable component identification, see Figures 4–7. assembly. Position assembled trigger in handle and drive roll pin through holes in handle and trigger.
- Page 13 2015 series Pneudraulic Installation Tools (HK958) ill and leed This section documents the “bleed-&-fill” procedure. For NOTE: Rock the tool to free trapped air. Do not component identification, see Figures 2–2 allow air to re-enter the tool. Always hold the fill...
-
Page 14: Fill And Bleed
2015 series Pneudraulic Installation Tools (HK958) ill and leed continued BLEED PROCEDURE FOR PARTIALLY FILLED Carefully add fluid to “top off” the fluid in the fill port. TOOL IN FIELD USE Insert and tighten the bleed plug. 1. Disconnect the tool from the air supply. Lay tool on 9. -
Page 15: Measuring Tool Stroke
2015 series Pneudraulic Installation Tools (HK958) eaSuring troke NOTE: Remove the Nose Assembly from the tool for both of the following procedures. WITH A STALL NUT 1. Disconnect the tool from the air-line and remove the igure nose assembly. 2. Reconnect the tool to the air-line. Press and hold the trigger to cycle the piston fully to the rear of the tool (the end of the PULL stroke). - Page 16 2015 series Pneudraulic Installation Tools (HK958) 2015 2015b & andle igure NOTES: Piston Assembly 125156 includes: Piston (not sold separately) ---- 506160 Polyseal 506653 Retaining Ring 506654 Washer Front Gland Assembly 123775 includes: Front Gland (not sold separately) ---- 122432 Gland Cap...
- Page 17 2015 series Pneudraulic Installation Tools (HK958) 2015V andle igure...
- Page 18 2015 series Pneudraulic Installation Tools (HK958) all ModelS igure Tighten and torque to 36–66 ft.-lbs. 130727 NOTES: Cylinder Head Assembly 123778-1 includes: ---- Cylinder Head (not sold separately) 500864 O-Ring Throttle Valve Assembly 125472-2 includes: Throttle Valve (not sold separately) ---- 507396 O-Ring (qty.
- Page 19 2015 series Pneudraulic Installation Tools (HK958) igure 506576 Plug & Gasket Assembly 104293 Bleed Plug Assembly 125116 Guard 505438 O-ring...
- Page 20 2015 series Pneudraulic Installation Tools (HK958) iSton and ront land SSeMblieS igure iSton and ront land SSeMblieS eMoVal igure iSton and ront land SSeMblieS nStallation...
- Page 21 2015 series Pneudraulic Installation Tools (HK958) roubleSHooting Always check the simplest possible cause (such as a loose or disconnected trigger line) of a malfunction first. Then proceed logically, eliminating other possible causes until the cause is discovered. Where possible, substitute known good parts for suspected defective parts.
- Page 22 2015 series Pneudraulic Installation Tools (HK958) & cceSSorieS continued igure 2015 i odel nSert NOTE: Pintail Tube (P/N 125135-1), supplied with the tool, must be used with all -06 products. intail ollection 244bt pictured on tool igure...
- Page 23 2015 series Pneudraulic Installation Tools (HK958) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after 12/1/2016 HUCK makes no warranty with respect to the tooling, part(s), or other items manufactured by third parties.
- Page 24 Arconic Fastening Systems and Rings world-wide locations: AMERICAS EUROPE FAR EAST Kingston Operations...
Need help?
Do you have a question about the 2015 series and is the answer not in the manual?
Questions and answers