Table of Contents
Advertisement
Quick Links
Instruction Manual
ERT1S ERT2S ERT3S ERT4S
Ebbert Rivet Tools
Disassembly and Assembly
Instructions ERT1S & ERT2S
Disassembly and Assembly
Instructions ERT3S & ERT4S
Makers of Huck
December 9, 2016
Brand Fasteners, Tools & Accessories
HK1038
Components Drawings
, Marson
, Recoil
®
®
3-4
5
5
6-7
8-9
9-10
11
11
12-15
16-17
18
18
®
Advertisement
Table of Contents
Related Manuals for Arconic ERT1S
Summary of Contents for Arconic ERT1S
-
Page 1: Table Of Contents
Safety Instructions Instruction Manual ERT1S ERT2S ERT3S ERT4S General Information Ebbert Rivet Tools Principle of Operation Specifications Disassembly and Assembly Instructions ERT1S & ERT2S Disassembly and Assembly Instructions ERT3S & ERT4S 9-10 Rivet Tool Handle Function Air Bleeding Instructions Components Drawings... - Page 2 ERT_S series Ebbert Rivet Tools (HK1038)
-
Page 3: Safety Instructions
ERT_S series Ebbert Rivet Tools (HK1038) Safety Instructions 15. Check clearance between trigger and work piece to ensure GLOSSARY OF TERMS AND SYMBOLS: there is no pinch point when tool is activated. Remote - Product complies with requirements set forth by triggers are available for hydraulic tooling if pinch point is the relevant European directives. - Page 4 ERT_S series Ebbert Rivet Tools (HK1038) Safety Instructions (continued) IV. REPETITIVE MOTION HAZARDS: VIII. VIBRATION HAZARDS: 1. When using assembly power tool, the operator can 1. Exposure to vibration can cause disabling damage to the experience discomfort in the hands, arms, shoulders, neck nerves and blood supply to the hands and arms.
-
Page 5: General Information
This manual contains operating and service procedures Specific instructions for each tool are given under that for the Ebbert Rivet Tool models ERT1S, ERT2S, tool model number heading. While they may appear to ERT3S, ERT4S, and their optional tool configurations. -
Page 6: Specifications
ERT_S series Ebbert Rivet Tools (HK1038) Specifications igure nches ERT1S WEIGHT: 3 lbs. (1.36 kg) STROKE: 0.75 in (19.05 mm) RATED PULL FORCE: 1,992 lbs. FASTENER SIZES: 3/32” through 3/16” igure nches ERT2S WEIGHT: 3.25 lbs. (1.47 kg) STROKE: 0.9375 in. (23.81 mm) RATED PULL FORCE: 4,330 lbs. - Page 7 ERT_S series Ebbert Rivet Tools (HK1038) Specifications (continued) igure ERT3S WEIGHT: 3.5 lbs. (1.58 kg) STROKE: 0.75 in (19.05 mm) RATED PULL FORCE: 1,992 lbs. FASTENER SIZES: 3/32” through 3/16” nches igure ERT4S WEIGHT: 3.5 lbs. (1.58 kg) STROKE: 0.9375 in. (23.81 mm) RATED PULL FORCE: 4,330 lbs.
- Page 8 “V” groove is open. igure Assembly ERT1S & ERT2S This procedure is for the re-assembly of the ERT1S & ERT1S: With piston forward stop placed on the piston ERT2S tools. shaft, insert end cap assembly into piston, then slide 1.
- Page 9 Use option “a” or “b” to fill tool wrench flats carefully to prevent nicking seal edges. with hydraulic fluid: 7. ERT1S: Insert piston rod guide and wiper assembly, a) Gravity fill: Connect hydraulic line to power unit pushing the hydraulic seal down into cylinder. Secure and allow hydraulic fluid to flow from the higher piston rod guide with two screws.
- Page 10 ERT_S series Ebbert Rivet Tools (HK1038) Assembly ERT3S & ERT4S This procedure is for reassembly of ERT3S & ERT4S. 6. Slide hydraulic seal down over piston threads and wrench 1. When replacing seals, make sure they are correctly flats carefully to prevent nicking seal edges, and position positioned as shown on the Tool Schematic.
-
Page 11: Rivet Tool Handle Function
It is easy to remedy the problem. Remove the trigger pin, trigger, and valve plunger for Quad-ring replacement. On models ERT1S and ERT2S, the handle is adjustable through a 20-degree arc. This patented design allows relief to the wrist &... - Page 12 ERT_S series Ebbert Rivet Tools (HK1038) Components Drawing ERT1S igure...
- Page 13 ERT_S series Ebbert Rivet Tools (HK1038) Components Drawing ERT2S igure...
- Page 14 ERT_S series Ebbert Rivet Tools (HK1038) Components Drawing ERT3S igure...
- Page 15 ERT_S series Ebbert Rivet Tools (HK1038) Components Drawing ERT4S igure...
-
Page 16: Optional Tool Configurations
ERT_S series Ebbert Rivet Tools (HK1038) Optional Tool Configurations Figures 9–13 show the five optional ERT1S and ERT2S configurations that are available from Huck. Based on the application needed, the optional-configuration tools may ship: • Without Handle (L series) •... - Page 17 ERT_S series Ebbert Rivet Tools (HK1038) Optional Tool Configurations (continued) igure Refer to ERT2S Parts List (Figure 6) igure Refer to ERT1S Parts List (Figure 5)
-
Page 18: Kits And Accessories
Energized Seal Service Kit - 300473 Piston Assembly Bullet - 300072 Filler / Bleed Pump Assembly (for ERT2SLE) - 300509 Service Kit ERT1S, 1SL, 1SMQ - 300467 (also fits ERT3S) Service Kit ERT2S, 2SL, 2SMQ - 300466 (also fits ERT4S) Troubleshooting Always check the simplest possible cause (such as a disconnected air hose) of a malfunction first. - Page 19 ERT_S series Ebbert Rivet Tools (HK1038) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after 12/1/2016 HUCK makes no warranty with respect to the tooling, part(s), or other items manufactured by third parties.
- Page 20 Arconic Fastening Systems and Rings world-wide locations: AMERICAS EUROPE AUSTRALIA Kingston Operations...
Need help?
Do you have a question about the ERT1S and is the answer not in the manual?
Questions and answers